Question about Cars & Trucks

Open Question

Replace door lock xh falcon

Need to replace internal door latch xh falcon

Posted by Anonymous on


5 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: I need to remove the drivers internal door panel

Remove plastic studs from door closer. Unscrew three retaining screws. remove grab.
Unhook window winder retaining clip. Best done with small long-nose pliers. window winder retaining clip located inside plastic winder handle section. Will need to prise away winder handle from door slightly to expose clip. locate and gently pull clip from winder shaft.
unscrew door opener / lock assembly retaining screw.
gently prise lower trim retaining press studs from door. remove lower trim.
gently , from rear of door, pull upper trim from door and similtaniously prise upper trim press studs from door.
gently giggle door opener / lock assembly through upper trim . remove trim
gently with flat blade, peel off plastic dust sheeting.
access to inside off door is now possible.
Reassembly reverse of above

Cheers !


Posted on Feb 22, 2009

  • 532 Answers

SOURCE: How do you replace the front door latch assy on

You will have to cut the rivet holding the lock solenoid,you will need to move the solenoid around to un-hook it from the rod.Be careful because the part the rod hooks to is plastic and i already broke mine on my 1994 Bronco.while replacing the latch,consider replacing the cable for the inside handle-they stretch and makes you pull harder on the handle until it breaks the handle off.I got tired of replacing the plastic handle so i made one out of steel at my work.

Posted on Feb 26, 2010

  • 10515 Answers

SOURCE: washed my xh falcon its


There could be few reasons for the same. You might have covered all the basic troubleshooting steps.You may have water in the distributer cap, remove the cap and clean out with water dispersing agent such as WD40.It may be a faulty MAP sensor or if the coil could be giving a weak spark, if the spark cannot jump at least a 1.5cm gap then replace the coil.Check the injectors and the fuse links to make sure there is nothing wrong with them.

Let me know,once you check all the above.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Dec 24, 2010

  • 2418 Answers

SOURCE: Hi I have got a

I did my best to research this problem back the first time I saw it posted. What I came up with is use the computer from the donor engine/car. Your Neutral switch should also come from the donor in respect this switch is found on the clutch in a manual car not on the trans itself as in a auto. The reverse light will also come from the manual trans, and to find which wire is which in transplant car. Use a jumper wire and probe the harness till the reverse lights come on. I can not find a schematic for these cars on the net. Your best bet will be to get a shop manual for both and find the wires there. I hope to have been some help to you.

Posted on Jan 15, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Drivers door latch won't catch. most cold mornings when the latch doe's work i cant open the door

door lock may be sticking due to water ingress and maybe sticking due to frost. spray plenty water displacement fluid in /around locking mechanism. you may also need to remove door card and access internals of latch to spray also.

Jan 12, 2016 | 2000 Mercury Sable

1 Answer

How to replace a heater hose on XH falcon ute

Drain the coolant, remove the clamps, remove and replace the hose, replace the clamps and refill the coolant

Oct 12, 2014 | Cars & Trucks

1 Answer

Bmw troubleshoot

Has anyone been inside the door panel recently? If so it is possible they did not plug the actuator connector back up. using a pencil, try to engage the latch and lock it. Does it lock? Does it release when you pull the inside or outside handle? The latches can internally fail without notice. It is possible the actuator is frozen. If it is it will need to be replaced.

Sep 03, 2014 | 2006 BMW 750Li

1 Answer

Xh fuel pump cuts out

Are you refer at Falcon XH ? Are you check fuses and wires and volateg at/from fuel pump ?

Jun 27, 2012 | Ford Falcon Cars & Trucks

1 Answer

Ba falcon door won't close

check that the lock mechanism is not already in the closed position
use a round bar under the latch and pull it into the open position as you press the door handle

Apr 28, 2012 | Ford Cars & Trucks

1 Answer

Front passenger door won't shut, i tried rotating the latch and it moves to the position but the it wont latch what do i do?

If the door hinges are in good condition and the latch still aligns properly with the striker, good chance that the latch mechanism has broken internally. It's not a difficult repair. You can get a replacement at most local scrapyards for around $10.00 and you only need to change the mechanism, not the lock.
Just remove the inner door panel, disconnect the control rods and remove the fasteners for the latch.
Reverse procedure to install.
Before going out and replacing it, spray the latch with wd40 or other solvent just to make sure it isn't internally binding. If it works, then don't bother with the replacement.

Feb 10, 2011 | 1993 Jeep Grand Cherokee

2 Answers

My driver side door wont close. the handles seem to do nothing. any advice?

the door lock mechanism has a broken spring internally .door lock has to be replaced.

Jan 15, 2010 | 1998 Ford Windstar

2 Answers

2000 au ford falcon sedan door locks chatter when unlocking (3 clicks()

If they aren't locking and unlocking properly, or are jumping, it is probably a broken worm gear in the door lock. You can buy new ones on ebay.

Jan 08, 2010 | Ford Futura Cars & Trucks

1 Answer

I have a 98 jeep grand cherokee, and my driver side door lock is in the lock position and I can not shut my door. How do I release the lock?

Have you tried unlocking it with the key? If that does not work, try moving the latch with a scredriver, back into the open position. If the latch has broken internally you will need to remove the inner door panel and remove the latch assembly for visual inspection and replacement. You can get another latch at just about any scrapyard and key will not need to be changed to do this.

Oct 21, 2009 | 1998 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides