Question about Ford Mondeo

Open Question

How tu instal taxi meter in ford mondeo

Can anyone tell me how to install a taxi meter in mondeo 2011 i cant find a information plz help me

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 172 Answers

SOURCE: 2001 Ford Mondeo 1.8 petrol. engine went in the

Check ECM (aka) Electronic Control Module (COMPUTER)

Posted on Aug 11, 2009

  • 4970 Answers


Leave SWITCHED ON...UNDISTURBED for a couple of hours and it will automatically reset itself

Posted on Sep 11, 2009

  • 506 Answers

SOURCE: ford mondeo 2001 both the head lights not working

Your relay is more than likely the culprit. There is a relay box in the engine compartment that houses this relay. A relay is used to control a high current or high voltage source with a low current low voltage source. There should be a diagram on the bottom of the relay housing cover.

Posted on Feb 17, 2010

  • 80637 Answers

SOURCE: How to hook up a

we have no instructions for this at fixya, contact the maker of the meter please

Posted on Sep 23, 2010

  • 1 Answer

SOURCE: I need to install a centrodyne pulse divider in my

Call Lee at Centrodyne he will help you.
The pulse is most easily found on the transmission at the VSS output. It is a connector with two wires, you want the DG/V. Run that to the pulse divider green wire. From the meter, tie the white in the 2 stand cable to the pulse output. Hook up power and ground then calibrate the meter. You should end up in the 33,000 range for calibration.

Posted on Feb 11, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

2011 Ford Mondeo will not start

Check the neutral switch on the transmission.

Oct 10, 2014 | 2011 Ford Mondeo 1.6

1 Answer

Hi, twice our 2011 ford mondeo diesel has been to two different ford dealerships and both times they have carried out perticular burn offs for a blocked particular filter. This has happened in a 3 month...

That is a question you need to ask the dealer. The cause could be you have a rich fuel condition, this causes high carbon particulates and this clogs the filter. If the engine is running correctly then a filter might fix the issue. But I warn you it is big bucks (American slang for allot of money) for this part and the install has to be down by the dealer.

Jun 24, 2014 | 2011 Ford Mondeo 1.6

1 Answer

Set clock on cygnius taxi meter

We only have information on factory installed systems. please contact the maker of the meter for assistance with this.

Nov 05, 2012 | Cars & Trucks

1 Answer

Wiring for a lucastronic taxi meter

I have just bought a lucastronic taxisim meter just as a little project. I am not installing it into a vehicle and currently trying to power it off of a PC psu. I am able to get it to come on where is say calculating and then changed to "dead bulb". Does anyone have any idea's how I stop the error or which wire needs what to stop it. I use the red, yellow and black to power it which leaves the green and purple unused.

May 23, 2012 | Cars & Trucks

1 Answer

Need cam timing spec for mondeo st220

For camshaft timing spec,click the link below :----Ford Mondeo ST220 camshaft Timing specifications?
-------This will help.
Also check this related help links:---

How test cam shaft? Testing Car Camshaft?
----------How to Inspect Camshaft?
------------Crankshaft and camshafts timing marks?
----------Camshaft, Bearings & Lifters Replacing ?
---------Camshaft Position (CMP) Sensor replacing?
------------How to replace Camshaft? Replacing Vehicles Cam Shaft Assembly?
---------This will help too.Thanks.

Feb 13, 2012 | Cars & Trucks

1 Answer

I am looking for the speed signal output wire for a 2005 kia sedona.I am trying to hooh up a taxi meter.Can you help

Do not hook anything to a vehicles electrical system
You will load the circuit and have all kinds of issues.

The Speed Sensor is an output sensor that sends a signal to the
vehicles computer, for shift control stratagy. The output
will also be unusable for what you want to do.

Follow the taxi meters instructions

Jan 30, 2011 | 2004 Kia Sedona

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

104 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides