Question about Cars & Trucks

Open Question

Toyota dyna 150 not charging

Bulb replaced in dash fuses ok alt checked and ok

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 383 Answers

SOURCE: 2001 subaru outback headlight not working

chapmnfarm: your head lights use a "2" fuse system.
one for the left and one for the right.
The fuse box you are looking for is under the hood on the passenger's side. It is a black box roughly 8 inches long and 4-5 inches wide. When you remove the cover, you will see fuses and relays. What you are looking for is the section in the box which has a cluster of 7 fuses. 3 in one row and 4 in the other. On the outer parameter are two relays. The fuses you are interested in are located in the row of 4 fuses, with the two closest to the "L" shaped part of the box. Both of those should be 15 amp fuses.
The fuse below those should be a 20 amp which is the lighting switch and the one below it is a 15 amp which is for the interior lights and the clock.
Check your harness grounds in the engine compartment near the area you have the problem. There are ground wires which come out of the harness on both sides of the core support. The wires are black in color and have "EYES" crimped onto the ends of the wires. Both of them will probably be located about 4-6 inches below the upper tie bar on each side of the radiator. Odds are that the eyes will be large enough to pass a 6mm bolt through.
I hope what I have given you will resolve your problem. Lem me know,,good luck>>>>>>>>>>>>>>>

Posted on Apr 19, 2009

Ad
Molson02536
  • 3854 Answers

SOURCE: How to replace light bulbs in the dash board of a

Get a Toyota shop manual before you attack the dash. There are a number of screws and clips that are not obvious, and there is a good chance you will get frustrated and break something if you just go at it.
On the Sienna, Your going to remove a good portion of the dash just to change light bulbs on the instrument cluster.

Get a shop manual, and the job will go smoothly. I would have not figured it out half the things is do without the instructions to what i am working on.

I know the dashboard HAS to come off. This may not help but I'm sure if you check the dealer they can give you an estimate of time/labor vs part cost.

Knowing the cost will make you invest in a shop manual, or you can go to Auto Zone or Parts Source for a print out, there free and you can get the parts from there too.
Good luck.

Posted on May 04, 2009

  • 290 Answers

SOURCE: no low beams bulbs are ok fuses look good

There may be a relay that operates the low beam lights, check the owners manual to see if there is a relay, you should be able to hear it go "click" if there is one.

Posted on Dec 26, 2009

Sean80000
  • 1867 Answers

SOURCE: brake lights not working,

Assuming the wiring to the brake lights is serviceable, you will find that the brake light switch, which is activated by the brake pedal for the brake lights, will have failed and will need to be replaced.


Just ensure you first replace the fuse and both brake light bulbs as an initial step and then re-check to ensure you still have no lights.

Sean

Posted on Jan 02, 2010

  • 510 Answers

SOURCE: mazda eunos dash lights and rear lights not working

Check fuse f3 located in fascia fuse box,below steering wheel just above data link connection 15AMP
Fuse under bonnet f7 also connected to dash/rear lights,but if this blows you would have no indicators as well
good luck barry

Posted on Mar 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

How to check alternater charging


start engine hold at 1500 rpm and disconnect battery if car stops the alternator not working .

Jan 18, 2017 | Suzuki Cars & Trucks

1 Answer

Battery light alternator


The Charge lamp comes on with the Alternator fails to keep battery charge going. (lots of way to fail, and ALT Is 100% good) it's a system. each part of it must be good, end to end.
so...
i put my voltmeter across battery, i start car, i see 13.3 to 15vdc, alt is good.
no? , i see now, 12.2v. ALt is dead, (i didnt say bad) and battery is sightly discharged, 12.6v is charged. (key off, rested voltage)
This 12v tells me the ALT is shut down. only why is the question.

how can any charge system fail,
bad battery tops the list here, they LOVE to fail.
1: belt slips.
2: belt missing
3: bad alt.
4: bad wires to ALT . (corrosion on any wire or lug)
5: fuses blown , any listed below.:
your alt is not an ECU controlled, alt ,its 100% self contained

did you ever remove the ALT and blow the 100 amp fuseable link
the first step of any alt pul, is the pull the NEG, battery lug or BOOM.

im logged in to alldata.com so can you.

and what do i see.
a 5 wire ALT. one is the frame ground, so it must not be rusty or..... it fails. frame to engine block. no rust here.

wire L , yellow.goes to dash LEDs (alt failure idiot lamps) (this works)
wire. S white goes to ALT 5a fuse, is it blown?
wire :B B/G color, goes to the 100 amp link fuse. (blown>?)
wire IG Red-white, goes to a fuse marked 10A gauge.

i think the IG wire is the voltage sense wire.
no sense, no charge. I think the whole I/P dash cluster goes dead when this fuse blows.

The S wire is the boot strap voltage sense, it wakes up the regulator .
if open , the reg stays asleep, as does ALT.
Alternators can not self start, the regulator has boot strap device
that cures that. called self excitation. so this wire is critical.
All wires except the L wire is critical. in this case.

the B wire is the big wire, it charges the battery . 50amps or more..

any of the 5 paths open , kills the ALT dead.
The REG inside the ALT can also shut it down.
eg: battery bad, with huge cell resistances. total.
eg: overvoltge for any reasons. including attempts top run car with no battery, (dont ask)
eg: over current (battery cells 1 to 6 shorted) or 25 KC lamps added.
eg: over temperature shut down.

that is about it.







Dec 31, 2013 | 2003 Toyota Matrix

1 Answer

Toyo dyna 92 break lights not working , is there a fuse for this or is it hard wired bulbs ,work fine , ?


There is a fuse for the brake lights. Check fuse and replace if blown. If the fuse is not blown, check the bulbs themselves. If the bulbs are good, then the next step is to replace the brake light switch located under steering column attached to brake pedal rod.

Feb 16, 2010 | 1992 Toyota Xtracab

2 Answers

Brake lights not working,


Assuming the wiring to the brake lights is serviceable, you will find that the brake light switch, which is activated by the brake pedal for the brake lights, will have failed and will need to be replaced.


Just ensure you first replace the fuse and both brake light bulbs as an initial step and then re-check to ensure you still have no lights.

Sean

Jan 02, 2010 | 1993 Toyota Celica

2 Answers

No brake lights 1990 ford f 150


First, check fuses. If the fuse for tail and brake lights is OK, check the bulbs. If they are OK, you need a new brake light switch, which attached to the brake pedal under the dash. The part should be less than $20. These are a common replacement item on older fords.

Dec 20, 2009 | 1990 Ford F150

1 Answer

Location of Alternator relay in 1987 Nissan Pintara 4cyl EFI, new alternator, new battery, fusable link ok, not charging properly, no charge light on dash.


I am assuming that when you say no alt light on dash , you mean that when you first turn key on for the bulb check it won't light. i f this is true then I would be looking at replacing the bulb first. most car's use the bulb in the dash as part of the excitment circut to get the alt to start charging.

Aug 29, 2009 | 1987 Nissan Stanza

1 Answer

I put my 87 4runner in reverse and it blows the 15A engine fuse


Hello there:
I would first refer to the owners manual to make sure that the fuse that is blowing is of the right amps also check the fuses under the hood too. than i would check to see if there is any shorts anywhere and get them fixed. You can also take the car to autozone and have the free diagnostics done on the vehical ok?
hope that htis has helped out some.
best regards mike

Aug 25, 2009 | 1987 Toyota 4Runner

1 Answer

Alternator f-150


replace the link between the alternator and the positive side of the battery. This is a fusable link and sometimes can cause this problem this would be the easy fix and is hard to test

May 17, 2009 | 2002 Ford F150 Regular Cab

4 Answers

Dashlights and temperature dash lights not working


Turn on your headlights and check to see if your taillights are working. They act as a fuse to your dashlights, its a safety thing

Nov 11, 2008 | 1986 Toyota 4Runner

1 Answer

Replace park lights on 1998 camry


If your dash lights work, your park light fuse is OK.

Jul 27, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

15273 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...