Question about Cars & Trucks

Open Question

Serpentine Belt Diagrams1994 dodge 318 b250 with air

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2 Answers

SOURCE: serpentine belt diagram:

The belt routing diagram is located on the top radiator cross member by the hood latch. You should see it when you open the hood. If it is not there, all Chrysler, Dodge, and Plymouth minivans, from 1993 to at least 1999, used the same 3.3L engine setup, so find someone with one and look for the diagram where I described.

Posted on Jul 18, 2008

BCally1
  • 133 Answers

SOURCE: serpentine belt diagram for a 5.9 diesel with air and 9 pulleys

5.9L DIESEL
196759.jpg The 5.9L diesel engine accessory drive system (with a/c) consists of :

  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
  8. A/C Compressor Pump Pulley (8)
CAUTION: When installing the accessory drive belt, the belt must be routed correctly. If not, engine may overheat due to water pump rotating in wrong direction. Refer to or for correct engine belt routing. The correct belt with correct length must be used.
1. Position drive belt over all pulleys except water pump pulley. 2. Attach a 1/2 inch ratchet to tensioner.


196757.jpg The 5.9L diesel engine accessory drive system (without a/c) consists of :
  1. Generator Pulley (1)
  2. Water Pump Pulley (2)
  3. Idler Pulley (3)
  4. Power Steering Pump Pulley (4)
  5. Radiator Fan Pulley (5)
  6. Crankshaft Pulley (6)
  7. Automatic Tensioner (7)
3. Rotate ratchet and belt tensioner clockwise. Place belt over water pump pulley. Let tensioner rotate back into place. Remove ratchet. Be sure belt is properly seated on all pulleys.

Posted on Jan 22, 2009

  • 1757 Answers

SOURCE: Need serpentine belt routing diagram for 1994 Dodge grand caravan

3.3L?
Looking at the engine from front (right side of the Van): Stating at the Top, Going Left to Right and Clockwise:
Over the Alternator
To under the Idle Pulley,
To Over the AC Compressor.
To the Left Side of the Water Pump.
To the Right side and Under the Crankshaft Pulley
To the Right side and Over and Down the Tensioner
To Under the Power Steering Pump
And Back up-to the Left side of the Alternator.
Advise when puting it on:
Put the Belt around everything else accept for the Alternator. After it is around all the rest of the Pulleys - Pull the belt up - tight from the Power steering Pump and the Idle Pulley to form a loop, holding the Belt close to the Altenator Pulley.
Using the 15mm wrench or belt tensioner bar - rotate the Tensioner Pulley towards the front of the Van and then place the belt over the Alternator.
Let me know if this helped or if you have additional information or questions. Feel free to contact me at FixYa.com!

Posted on Jan 22, 2010

  • 31 Answers

SOURCE: Serpentine belt replacement for a 2004 Dodge 3500

check the hood or the frame rail around the engine bay. there should be a diagram.

Posted on Feb 22, 2010

  • 1 Answer

SOURCE: 1989 Dodge Truck B250 Van V8-318 ignition control

its built into the ecm located right in the middle of he firewall from under the hood, big black box with two plugs.

Posted on Apr 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need diagram for 95 dodge van B250, 5.2 serpentine belt


go to his web sight and down load the diagram book and then look up your make and model.


http://www.doocu.com/pdf/search/gates+auto+belt+routing

Apr 12, 2011 | Dodge Ram B250 Cars & Trucks

1 Answer

I need to no where my igniton control module is located at on my 1992 dodge b250 it has a 318


You have a hall effect pick up coil, it is in the distributor, under the rotor-it has a 4 wire harness that comes out of the cap and plugs into a harness-the pick up coil just lifts out, easy fix.

Jan 27, 2011 | 1988 Dodge B250

1 Answer

Looking for a diagram for a serpentine belt for a 2006, Dodge 2500


The main drive belt or serpentine belt is important on any vehicle, but some have more than one belt to drive components from the crankshaft. The Dodge Ram and similar truck models have one true serpentine belt, a multi-ribbed belt that fits into grooves on various pulleys, that Dodge suggests inspecting for wear every 15,000 miles or 12 months.

Disconnect the negative battery terminal. Because the electric fan can start even without the vehicle running, some mechanics suggest disconnecting the battery terminal while working in the serpentine belt area.
2Locate the serpentine belt tensioner pulley. The belt tensioner pulley will have a bolt on its side. On some Dodge Ram models, the tensioner is directly below the air conditioner compressor pulley; look for it above the crankshaft pulley.
3Rotate the tensioner pulley by turning the bolt, either with a wrench for some models or a breaker bar or ratchet for other models.
4Slip off the belt and let the tensioner return to its position.

Aug 21, 2010 | Dodge Ram 2500 Cars & Trucks

1 Answer

Loud squeal noise from serpentine belt on 99 dodge truck with 318 motor when its cranked up


If you have an manual adjuster you need to tighten or replace the belt, belt treatment may help.
If you have an automatic adjuster. You can try belt treatment, if it doesn't work you'll need to replace the belt and maybe the adjuster.

Jun 06, 2010 | 1998 Dodge Ram 1500 4WD

2 Answers

1989 Dodge Truck B250 Van V8-318 ignition control module location?


its built into the ecm located right in the middle of he firewall from under the hood, big black box with two plugs.

Jan 31, 2010 | 1988 Dodge B250

1 Answer

What transmision is in a 1990 dodge ram van b250 with a 318 moter?


You will have to refer to the id on the pan or on a tag on the transmission. There is the 727,904,and the 999.

Jan 12, 2010 | 1987 Dodge Ram Wagon B250

1 Answer

How to remove and replace an alternator on a 1994 Dodge B250 van.


To release belt, You need breaker bar with a 15mm or 19/32" socket . There a auto tensioner to left of the alternator. Place the socket on silver color bolt and pull breaker bar to the right this will relaese the belt.

Jul 02, 2009 | 1994 Dodge B Series Cargo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...