Question about Cars & Trucks

1 Answer

Mg Rover Manual 1600 1800cc Turbo

I have had clutch plate failure twice @ 100,000 and 120,000. Where motor cut out and coasted to a stop. Now at 126,000km Clutch pedal falls to floor. Start motor, all OK. Now start engine, lift pedal a fraction (2-3mm) - car jolts forward - I Brake, engine stalls. I cannot drive it. Please advise what is wrong? I have had this in other older cars when there is a shortage of Brake Fluid, But Hand Book does not explain. Also no warning light on Dashboard. TOM KIRKLAND, Johannesburg, Gauteng, RSA.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 1,051 Answers

It might be a broken finger on the pressure plate for the clutch and that is allowing the pedal to stay on the floor and not return to the top.

Posted on May 20, 2017

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76070 Answers

SOURCE: clutch pedal floppy

The hydraulic clutch master cylinder is defective or the slave cylinder at the bell housing, it is recommended they replaced in pairs.

Posted on Dec 11, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Should the release bearing on a 1275 midget be touching the pressure plate when not in use


No it shouldn't touch. You might want to check and see if the clutch plate was installed the right way. If clutch plates are installed backwards, this will cause the tongs on the pressure plate to be pushed out further towards the bearing. And will squeal.

Oct 01, 2016 | MG Cars & Trucks

1 Answer

1. I have a 2004 Corolla 130-horsepower 1.8L 5-speed manual FWD, I Can clutch and put it into gear, any, but there is no response, and a somewhat noisy , rough sounding grind is heard. Any ideas what...


Sounds like you need to replace you clutch and pressure plate, the springs on the pressure plate have let go, replace it and all will be good, hope this helps

Feb 17, 2015 | 2004 Toyota Corolla 1.8

2 Answers

When i depreesed the clutch my truck is moving


If it has a hydraulic clutch it may low on fluid, check both brake and clutch fluid levels.

Sep 29, 2014 | Cars & Trucks

1 Answer

I have a 1993 dodge w250 with the 5.9L Cummins Diesel engine. yesterday I was driving and it seemed like the transmission came out of gear because the truck wouldn't move after I coasted to a stop. today I...


remove the inspection cover under the torque converter and check for failed flexi-plate drive. The plate that the torque converter is connected to that is attached to the crank shaft. Check the torque converter control (TCC) clutch solenoid/servo for failure.

Sep 14, 2013 | 1993 Dodge Ram 250

1 Answer

Noise in the clutch gearbox area on a 2000 discovery


Does this happen while moving? How much travel is on the clutch pedal before it 'Bites'

Jul 23, 2012 | 2000 Land Rover Discovery

1 Answer

Will a 1.8 20v gearbox off a passat fit on a 1.8 20v turbo automatic to make it manual?


yes but you would need to alighn a manual linkage and parts of the loom would need to be replaced as well as ecu etc so its not worth the trouble and then the clutch pedal should have studs and fixing positions on the chassis already but the plate to allow the hydraulic clutch pipe through might need cutting.The flywheel will need replacing and the clutch plate etc.

Feb 15, 2010 | 1999 Volkswagen Passat

1 Answer

Flat battery on rover 420 turbo diesel


hi, it may be that either your battery is faulty, have it drop tested, or if that is ok your starter motor may be faulty drawing to much current, ie, it needs a recon, hope this helps

Feb 03, 2009 | 1995 Land Rover Discovery

2 Answers

Mazda 626 2.2L Turbo 1989 - Alternator - Fuel Pump


Hi am just up the road on the SSC, it is easier to remove the alternator from underneath the vehicle & if you look under the carpet under the rear seat there is a plate which gives you access to the fuel pump cover in the tank. The pump can be accessed from there. If you want the workshop Manuals I have just uploaded them.
You can download the GD 626 Workshop manual & the Turbo supplement by going to the 626.net site.
Cheers

Jan 15, 2009 | 1988 Mazda 626 Turbo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...