Question about Cars & Trucks

Open Question

Honda activa rear wheel bearing size? - Cars & Trucks

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2 Answers

SOURCE: rear wheel hub nut

I used a 32 mm to remove hub nut on front. I guess it would be the same for back hub nut.

Posted on Aug 22, 2008

Ad
alicantecoli
  • 22246 Answers

SOURCE: WHAT SIZE SOCKET IS NEEDED

32mm

Posted on Nov 24, 2008

  • 14036 Answers

SOURCE: I need to know how to install a rear wheel bearing

its going to be hard to do at home you need a press to press out bearings and press them in

Posted on Apr 07, 2009

Mr BrokRench
  • 1623 Answers

SOURCE: I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic

Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

Posted on May 23, 2009

  • 632 Answers

SOURCE: how to change rear bearing mk 2 golf

If I'm not mistaken it's a 30mm

Posted on Apr 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changed rear bearing on 2001 Honda accord now it is tight and holding back when you drive


Is it the rear wheel bearing you have replaced?
If so, please jack up the rear wheel you fixed and try to spin the wheel by hand.
If it is tight, you will need to loosen the nut as it is too tight.
If it is loose, you may have your brakes too tight.
God bless your efforts.

Nov 27, 2015 | 2001 Honda Accord

1 Answer

Rear wheel bearing seized on Honda accord


youtube.com/watch?v=mjFMq0OitXo

Feb 11, 2013 | 2002 Honda Accord

1 Answer

Honda foreman trx450 right rear wheel wobbles. Bearings are good, but found that my axle nut was totally stripped. What could cause this


You say the rear wheel axles and bearings have been replaced, you mentionnothing of the front wheels, you have the symptoms of a front wheel bearing being worn out, remove them and check for pitting in the bearing rollers or the bearing races, I am sure you will find a problem. Hope this helps solve your issue with the bearing noise.

Oct 05, 2012 | Cars & Trucks

1 Answer

How to change back hub on 97 cr-v


Rear Brake Discs
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-1.1-800x800.jpg Replace the bearing and race as a single set. automotive roller bearing. image by Tom Oliveira from Fotolia.com

    Before raising the rear of your Honda, remove the dust cup from the center of the brake drums using a hammer and chisel. This will give you access to the spindle nut, which you can loosen using an axle nut socket. Then you can raise and remove the wheel/tire assembly ,or assemblies if you are replacing the bearings on both wheels.

    If your Honda model is equipped with rear disc brakes, remove the brake disc retaining screws, the brake hose bracket from the steering knuckle and caliper bracket mounting bolts. Hang the caliper to the coil spring using wire. Do not let the caliper hang free or the brake hose may be damaged.

    At this point, you will be able to remove the brake disc by hand. However, rust may have a firm grip on the disc. If this is the case, use a couple of 8-by-1.25 mm bolts and screw them evenly into the brake disc threaded holes. This will push the disc off the hub. Now you can finish removing the spindle nut and hub/wheel bearing assembly and install the new hub/wheel bearing assembly using a new spindle nut



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WDRoqv Rear Brake Drums
  • Fotolia.com" data-type="modal">honda-rear-wheel-bearing-removal-2.1-800x800.jpg Pack the bearing with bearing grease before installation. roller bearing image by Tom Oliveira from Fotolia.com

    If your Honda Civic comes equipped with rear brake drums, remove the center grease cup and loosen the axle spindle nut using an axle nut socket. After raising and removing the wheel/tire assembly, finish removing the axle nut and washer.

    You might be able to remove the outer wheel bearing from the spindle using a screwdriver. If not, wiggle the brake drum as you pull on it to let the bearing fall off the spindle. However, the brake drum might be caught in place by the brake shoes. In this case, you can retract the brake shoes through the hole in the back of the backing plate.

    Remove the rubber plug from the back of the backing plate. Then rotate the star wheel on the adjusting screw using a brake adjusting tool as you push the lever off the start wheel with a screwdriver. With the brake shoes off the brake drum, pull the brake drum off the wheel assembly. Then clean the brake assembly with brake parts cleaner and a clean, lint-free towel.

    Now you can set the brake drum on a workbench or hard surface and remove the grease seal and inner wheel bearing. The inner and outer wheel-bearing races can be removed using a drift punch and hammer. Pack the new wheel bearings with high-temperature wheel-bearing grease using a wheel-bearing packer and use a new grease seal during installation. Also, before reinstalling the brake drum, apply a thick coat of wheel-bearing grease to the cavity inside the hub, but do not fill it completely.



Read more: Honda Rear Wheel Bearing Removal ' eHow.com http://www.ehow.com/way_5974291_honda-rear-wheel-bearing-removal.html#ixzz1W3WN9eBb

Aug 25, 2011 | Honda CR-V Cars & Trucks

1 Answer

I need instructions on how to replace rear wheel bearings on my 1994 Honda Civic


Bearings are pressed into the hubs...much easier, faster and economical (if you don't have a press) to replace the complete bearing/hub assembly, no pressing is needed, since bearings are already pressed into the new hubs. Cost..aprox, 60 buxs each.
Here are the steps for the rear replacement...
Loosen the lug nuts on a rear wheel. 2) Chock the wheels and jack the rear of the car on the side with the lug nuts that you just loosened. 3) Remove the wheel by removing the lug nuts. 4) Pry open the dust cap covering the center of the axle/spindle. A small screwdriver tapped into the space between the hub and dust cap will work well for this. 5) With the dust cap now removed, use a thin center punch to straighten the little dent in the rim of the spindle nut so that you will be able to turn it freely in the next step. 6) Use a 32mm socket and a large breaker-bar to loosen the spindle nut. Unscrew the nut all the way and place it in a clean, safe area. 7) You should now be able to slide the hub/bearing assembly from the shaft. 8) Installation is the reverse of removal. Use plenty of high-temperature wheel bearing grease on all surfaces before you mount the replacement hub assembly.

IMPORTANT: Torque the spindle nut to 134 ft/lbs....(per manual specs)

When reinstalling the dust caps, tap them gently into place to avoid denting them...Install wheels, jack her down and pat yourself on the back...job complete.
Good luck..hope this will fixya up...please take time to leave me a fixya rateing...

May 23, 2009 | 1994 Honda Civic

1 Answer

Rear wheel hub


IF IT HAS REAR DRUM,WITH WHEEL REMOVED,REMOVE BRAKE DRUM,KNOCK OFF CENTER BEARING CAP,REMOVE STAKED LOCK NUT,AND PULL OF HUB AND BEARING ASSEMBLY.

Apr 07, 2009 | 2001 Honda Civic

2 Answers

Front wheel bearings


THe tire size is very important.
Originally ford aspire had 155 70 r 13.
It is impossible to find the same size in USA.
If you put a bigger tire...then you brake the wheel bearing.
My 2 cents
Art

Jul 19, 2008 | 1997 Ford Aspire

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

73 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...