Question about Cars & Trucks

1 Answer

Brake lights not working on 1996 ford taurus - Cars & Trucks

Posted by on

1 Answer

Check Brake Switch behind pedal arm

Posted on Jul 09, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

warlock61
  • 659 Answers

SOURCE: Ford taurus door ajar light stays on

Try using some WD40 in the door latches. Open and close the doors several times this should free up the sticking switch

Posted on Dec 19, 2008

emissionwiz
  • 75797 Answers

SOURCE: 1996 ford taurus odometer stopped working

the Speedo in your car is electronic, the problem is the tiny motor that moves the needle is most likely defective, there are no parts for the Speedo available to the consumer from Ford, you must remove the Speedo and have it repaired by a authorized Speedo repair shop. here is a link to a good one I know about.
http://dnaspeedometers.com/

Posted on Apr 01, 2009

emissionwiz
  • 75797 Answers

SOURCE: 1998 Ford Taurus/ Brake lights are not working.

most likely cause is that the multifunction switch is defective on the steering column. MOTORCRAFT Part # SW5599 Price $96.00

here is a photo.
0f44681.jpg .

Posted on Apr 27, 2009

  • 1596 Answers

SOURCE: Hazard Lights Won't Work on 96 Taurus

FIRST Check for Blown Fuse Then Locate Flasher Units @ Fuse Block to Determine Wiitch one is Hazard Turn On Key Then Turn Syg. Feel Flashers The One you feel Clicking is For Turn The Other IS Flasher Replace this Flasher unit.

  1. Verify the customer's concern by operating the turn signal/hazard flasher lamp to duplicate the condition.
  2. Inspect to determine if one of the electrical concerns apply: VISUAL INSPECTION CHART Electrical
    • Circuitry open/shorted.
    • Fuse junction panel Fuse:
+ 15 (10 A) + 29 (15 A)
  • Damaged multi-function switch.
  • Miniature bulb burned out.
  • Damaged lamp.
  1. If the inspection reveals obvious concern(s) that can be readily identified, service as required.
  2. If the concern(s) remains after the inspection, determine the symptom(s) and go to the Symptom Chart. See: ProceduresSymptom Chart(s)

Posted on Jun 01, 2009

  • 7353 Answers

SOURCE: 96 Ford Taurus no turn signals or hazards

Take the turn signal lever and jiggle it, a lot. If they start working, the switch is bad. You can also turn on the hazards and take hold of the button and push it left , right , forward and back and see if they start working. If so, replace the turn signal/ hazard switch.

Posted on Nov 25, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Third brake light not working ford taurus 1996


If we are talking of the high mount brake lamp the bulbs are accessed from the top of the rear deck. Remove the housing by pulling it firmly and there is access to the bulbs

Feb 28, 2015 | 1996 Ford Taurus

1 Answer

Gear shift wont shift from park


The park in this model is locked out by a pin, that pin is pulled back by an electric solenoid that is powered by the you guessed it, the brake lights. You either have a defective brake light switch (located above the brake pedal) or the connector to the switch is defective due to a broken conductor inside the wires plastic out insulating cover. It is a fairly cheap repair, You can override the lock out by turning the ignition key cylinder half way to the run position and wiggling the shifter at the same time, it may take a few tries but you can get it out of part this way.

Nov 16, 2011 | 1996 Ford Taurus

1 Answer

Ford taurus 1996 3.0 ABS ligth on


Hello, These warning lights are pretty accurate. Autozone, Advance, and Oreillys give free scans although the engine system and brake system can require different scanners.

Check your brake fluid level first. The ABS system requires sensors which require counting the revolutions of each wheel. Sometimes the sensors may break, but they can be blinded by dust and debris.

If you have a broken brake pad, the warning light can come on. Often the Emergency brake pad, inside the rear Rotor, can fall apart and trigger an ABS warning.

You need to inspect both the front and rear brakes or take your car to a brake shop for evaluation. Sometimes you can get a free estimate, and some shops can charge for inspecting the Emergency brakes because of the work needed to reach them.

Jul 07, 2011 | 1996 Ford Taurus

1 Answer

My 1996 taurus has the brake lights constantly on. when you disconnect the switch by teh brake pedal the car will not shift out of park but teh brake lights turn off???


CHECK BRAKE LIGHT SWITCH TO SEE IF ITS TOUCHING THE BRAKE PEDAL.IF BRAKE LIGHT SWITCH OR BRACKET LOOSE AND AWAY FROM BRAKE PEDAL BRAKE LIGHT WILL STAY ON.IF BRAKE LIGHT SWITCH INTACT BRAKE LIGHT SWITCH NEED REPLACING.WHEN REPLACING BRAKE LIGHT SWITCH OR IT NEEDS ADJUSTING MAKE SURE BRAKE LIGHT SWITCH PLUNGER TOUCHES BRAKE PEDAL ARM WHEN YOU RELEASE BRAKE PEDAL BRAKE LIGHTS SHOULD TURN OFF.

Sep 01, 2010 | 1996 Ford Taurus

1 Answer

Ford taurus 1996 - luggage compartment light


Directly underneath the Center Brake light assembly , under the lip of the trunk deck. Access to the Lights for the center Brake light are also there. It's set in a housing unprotected, easy to spot.

May 10, 2010 | 1996 Ford Taurus

1 Answer

96 ford taurus gear shift stuck in park


CHECK IF THE BRAKE LIGHT COME ON WHEN YOU HIT THE BRAKE PEDAL. IF DON'T. CHECK BRAKE LIGHT FUSE. COULD BE A BRAKE SWITCH. THERE IS A shift lock solenoid that receives a signal when the key is on and the brake pedal is depressed that allows you to move the shift lever to be taken out of park.

Mar 25, 2010 | 1996 Ford Taurus

1 Answer

Service engine soon light on a 1996 Ford taurus. I just had the brake line replaced 2 weeks ago because it had completely rusted out


when this light comes on it has nothing to do with the brakes it is an engine diagnostic faluire you must use an odb2 reader to read the codes see what the problem is and or reset the light! good luck!

Sep 08, 2009 | 1996 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...