Question about Jaguar XJ6

Open Question

Broken hood release 1985 xj6

Open engine lid when release cable inoperative

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: BROKEN HOOD RELEASE CABLE.NEED TO

One of the 2 cables on my hood release is loose. One works fine and releases (dirver's side) but the other is loose and does not. I cannot get my hood up. I have a 1998 Jaguar XJ8
Thank you ....

Posted on Sep 09, 2008

  • 196 Answers

SOURCE: Hood won't open. Cable is broken and can't get hood to pop.

NO there is no manual way . get a good flash light and look at teh latch through the grill or from under the truck and try and pop it with a long flat blade screw driver

Posted on Jan 11, 2009

  • 1 Answer

SOURCE: hood release cable broken, how do i open the hood ?

I have a similar problem with my 1992 Oldsmobile Cutlass Supreme. The way I open the hood is to reach my hand between the radiator and the front of the car, and for me there is a bar running right up the middle if I follew that too the top, and on the drivers side of that bar should be the hood release, and I feel around till I feel the hood release cable, and then I push on the lever that the cable is attached too, most of the time this works. Hope this helps.

Posted on Mar 24, 2009

defadad
  • 351 Answers

SOURCE: hood release will not release hood cable is not broken

the outer cable may have come loose near the lock, if the grille screws are accessable remove the grille and you will have access to the underside of the lock, you may need a screwdriver to push the lock lever aside to unlock the bonnet

Posted on May 23, 2009

  • 13 Answers

SOURCE: Broken tab to hood release cable

Get a long screwdriver and try to release the secondary latch that way. Or if you have small hands reach up under the hood and pull the secondary latch toward the left.

Posted on May 27, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Hood release with broken cable 2002 odyssey


look under the dash see if cable is broken close to that end
grip inner cable with pliers and pull hard

if broken at the engine bay
work from under the car with a long tool to release the bonnet catch

if not sure how its done drive to a panel repair shop for a solution

26237636-f4vzkd3ydwillbxdzd1jhjup-2-0.jpg

Jul 14, 2016 | Cars & Trucks

1 Answer

How do I open hood when cable or latch is broken


If the plastic hood release handle inside is broken, can you reach the steel cable, if so, use a pair of vice grips to grab the cable and pull. Sometimes it helps to have a helper standing at the end of the hood and pop the hood with palm of hand, in the area of under hood release mechanism, at the same time your pulling the cable.

If cable is broken, some makes and models, you can remove front grille and get at under hood release mechanism.

There is usually a primary hood release, inside vehicle, and a secondary release under the hood, you have to slide your hand under the hood to release, sometimes you have to press down on the hood a little to move release. Trying to shut the hood with secondary release engaged can be difficult, you don't have the distance and the weight of hood to swing down.

Nov 04, 2015 | 2007 Chevrolet Chevrolet HHR LT

2 Answers

1997 Isuzu Trooper, hood release cable broken at engine compartment end, how to open hood to fix


You can try accessing the latch from underneath the car using a long screwdriver, or try taking the front grill off and have at her.

Mar 17, 2013 | 1997 Isuzu Trooper

2 Answers

1985 corvette, pulled the hood release and the diverside opened but not the passengers side so now i can't open the hood, how do i release the passenger side that is stuck


have someone push down on that part of the hood while you pull the release. Usually that frees it and it should be adjusted up so it will open again

Apr 24, 2010 | 1985 Chevrolet Corvette

2 Answers

The hood latch cable broke under the hood how can i open it


Saturn Vue hood release can be opened (if the cable is not broken) by disconnecting the cable from the back of the release lever, grabbing the ball on the end of the cable with some large pliers ("channel locks") and pulling hard. A metal "wire keeper" bracket clamped to the cable end under the hood to serve as a spacer and the release lever works.
The purpose of this bulletin is to provide a procedure for opening the hood on the Saturn VUE and ION vehicles should the hood latch release cable mechanism become inoperative.

VUE Hood Opening Procedure Modify the Saturn radio antenna by bending the antenna mast 1 in. (2.54 cm) above the antenna base to a 25 degree angle

Open hood of similar vehicle to locate hood latch release cable to hood latch attachment point.

Using modified antenna, note approximate location that antenna will have to enter in between fascia and hood to access the hood latch cable attachment point. This should be toward the left edge of the Saturn emblem. Also note position of the modified antenna base. It should be angled downward.

Note: Use protective tape on the hood and fascia where the antenna will be inserted to protect the surfaces from scratches
On vehicle with inoperative latch, insert antenna between hood and fascia and depress the hood latch cable until the hood is opened.

Good luck and thank you for using fixya

Mar 15, 2010 | 2003 Saturn VUE

1 Answer

MY INSIDE HOOD RELEASE HAS BROKEN. IS THERE ANY


depending on where the cable is broken your can still release and open the hood. if it is broken inside the van in the footwell is the easiest...locate the end of the cable and with a set of visegrips pull the cable to release the hood.

Dec 07, 2009 | 1994 Plymouth Grand Voyager

1 Answer

Inop hood latch 1985 corvette


In the windshield wiper area on both sides of the car you will see a rubber plug about 1 inch in diameter. Use a flatblade screw driver (about 8-10 inches) and poke this plug out of its hole into the engine compartment (you can recover it later.) Insert your screwdriver through the hole until you find the release latch. Just push it until it releases.

Feb 08, 2009 | 1985 Chevrolet Corvette

1 Answer

Broken hood cable


Depends where cable is broken might be able to put vice grip on it and pull it from inside the car with the door open and you looking at the under dash lever. if can't then alternative is to lay on ground with a trouble light and look straight up under front where you think the hood latch is at if you can see the release then try to reach up and pry it enough to get hood to pop up on the safety then reach in and open it normally giving you time to see what is broken and to replace it. normally a book is available at the public library telling you how to specifically remove and replace broken and worn parts step by step, just find the proper book relevant to your model & make take it and see if it helps or not if it does your all set

Oct 10, 2008 | 1985 Cadillac DeVille

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

74896 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

455 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...