Question about 2006 Chevrolet Malibu Maxx

1 Answer

Air conditioning help

My air conditioning controls only work on the highest setting 4..1,2,3 dont work..

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Greenhorn:

    A rookie expert who has answered 20 questions on their first day.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Contributor
  • 27 Answers

Replace the blower resistor.

Posted on Jul 09, 2013

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76649 Answers

SOURCE: Climate Control buttons don't work

are you saying u can't change the air temperature? do the blower speeds work ok? can u change the locations the air comes from, i.e. dash registers, defrost, floor?

Posted on Jun 28, 2009

SOURCE: my blower control switch only works on level 4 or the highest setting. could there be a loose connectror while I still get resistance and

There are two possibilities here, the first, is a bad connector to the blower resistor, which is a very common problem in Colorados. Disconnect the plug to the resistor and check for burn spots on the pins, if you detect burnt spots, then replace the connector. If no burn spots are detected, replace the resistor.

Posted on Nov 14, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 Suzuki Reno air only works on settings1 2and 3


?? Hey Dawn,
I am guessing there are 4 settings..? Are these fan speed settings? There is a "Resistor" that controls the settings
http://www.rockauto.com/en/catalog/suzuki,2008,reno,2.0l+l4,1441791,heat+&+air+conditioning,blower+motor+control+module+/+resistor,6557

Jul 01, 2017 | Suzuki Cars & Trucks

1 Answer

Air does not blow


The car normally blows air through the blower however the controls and settings of the speed of the blower are controlled by the blower motor resistor. The resistor controls the speed of the blower fan. If your blower still works on the highest setting then the blower itself is still in working order. If you are not getting any air at all, even on the highest setting, then chances are the blower has gone bad, blown fuse or open wire. If this does not help please give us more information to work with.

Aug 12, 2012 | 2002 Buick Century

1 Answer

2004 honda cr-v blower motor does not run


Try going to this site as they have a lot of ideas: http://www.wikihow.com/Diagnose-a-Non-Working-Air-Conditioning-in-a-Car Also there are some videos on YouTube you may want to see: honda crv ac air conditioner blower does not run


I hope that helps you out!

Mar 31, 2017 | 2004 Honda CR-V

1 Answer

The blower motor for the air conditioning doesn't come on. The compressor comes on. I ohmed the blower motor and it was good. I jumped the blower motor and it turned freely. With the control set 1 2 3...


> With the control set 1 2 3 4 it does blow any air,
? does NOT?
A common problem with this control is the failure of a stepped resistor which causes only the highest speed to still function since this bypasses the resistor.
Tracing the leads from the fan speed switch may help locate it.

Sep 04, 2011 | 1997 Honda Accord

1 Answer

2001 Ranger XLT heat and air conditioning only work on high speed


there is a flapor motor that is controled by vacume, check for leaks in the vacume lines on the engine.

Sep 30, 2009 | 2000 Ford Ranger SuperCab

1 Answer

Air conditioning on my 2003 corolla only works on the highest setting, what could be the problem?


the blower motor resistor is gone or the tempature control module that has the switch has to be replaced.

good luck

Aug 15, 2009 | 2003 Toyota Corolla

1 Answer

Air conditioning blowing only highest setting but HOT air


Sounds like your freon has leaked out and your heater blower resistor is burned out. Deffinitly take this to the dealer.

May 20, 2009 | 2001 Honda Odyssey

2 Answers

Fan speed switch only works on #5


Call your local GMC Dealer and see if they have the climate control panel in stock. What happens is the circuit board on the back of the panel shorts out. The panel comes as an assembly and is very easy to replace. Don't go with a wrecking yard piece. I made that mistake once and it didn't work either. I got one from the Chevy dealer and it worked perfectly.

Aug 21, 2008 | 2002 GMC Sierra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8516 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...