rear door on driver side won't open,have taken the panel off the inside of car,seems like the lock won,t travelas far as it does on the other door.is there any way to open this door,thanks[1997 lincoln continetal]
-   Hey maltby, does your outside handle spring back into place after it has been pulled. Mine will not. I've been told that its the linkage on the handle that's broke. Now I need an Idea of how to remove the panel. Did you have to break any part of the panel to get it off? Are you able to see the handle linkage now that the panel has been removed? -   mjmoro315
Mar 29, 2009
-   You are not alone. I'm also looking for a clue as to what to do. If I come across the solution, I'll be back with it.-   mjmoro315
Mar 29, 2009
-   You are not alone. I'm also looking for a clue as to what I can do. If I get the solution, I'll be back to reveal it.-   mjmoro315
Using a small screwdriver, remove the screw cover from the armrest of rear door trim panel (27406).
Remove the two retaining screws.
Using Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry rear door trim panel from door inner panel.
Disconnect electrical connectors.
Installation
Position rear door trim panel on door inner panel, aligning two locators on rear door trim panel. Reverse Removal procedure.
Remove door trim panel and watershield. Refer to Section 01-05 .
Check all connections of remote control links and cables. Service as necessary.
Remove remote control assembly.
Remove door latch remote control assembly from latch assembly.
Drill out rivet at bellcrank and link (264B14).
Remove three screws attaching latch assembly to door.
Drill out rivet that attaches actuator motor to door.
Remove latch assembly with actuator motor and door latch control rod lever link assembly.
Installation
Install new bushings and clip onto latch assembly.
Install latch with links and power lock actuator into door cavity.
Position latch assembly to door, aligning screw holes in latch and door. Install three screws. Tighten to 10-13 Nm (89-115 lb-in).
Attach door latch actuator motor to door with a new rivet.
Install bellcrank and link to door using a new rivet.
Install inside door handle and remote control assembly to door.
Open and close door to check latch assembly operation.
Install watershield and door trim panel. Refer to Section 01-05 .
Item
Part Number
Description
1
221A00
Door Handle to Door Latch Actuating Cable
2
26446
Rear Door Control Rod Retainer
3
377901
Plug Button
4
26412
Rear Door Latch
5
W623451-S2
Push Nut
6
224A32
Counter Balance
7
22450
Door Outside Handle Tension Spring
8
W701210-S309
Screw
9
224A20
Outside Door Handle Anti Rattle Pivot (2 Req'd)
10
22404
Door Handle
11
224A24
Front Door Outside Handle Spacer (2 Req'd)
12
264A64
Rear Door Actuating Rod
13
22408
Outside Door Handle Anti-Rattle Bumper
14
22428
Outside Door Handle Large Pad
15
N621906-S2
Nut (2 Req'd)
16
N807329
Screw (3 Req'd)
17
26595
Rear Door Electric Latch Actuator (RH)
18
W701566-S47
Rivet
19
431C04-A
Rear Door Latch Striker Assembly
20
—
Door Lock Striker Plate (Part of Door Shell Assy)
21
W525172-S
Rivet (2 Req'd)
22
264B14
Bellcrank and Link (RH)
23
264A50
Bushing
24
N802034-SG
Rivet
25
26420
Rear Door Latch Control Rod Link
26
W525172-S
Rivet (2 Req'd)
27
21818
RR Door Latch (Inside)
28
A26460
RR Door Latch Push Button Rod
29
21982
Door Latch Rear Striker Assembly
30
N808377-S101
Screw (2 Req'd)
31
250A04
Rear Door Catch
32
N801010-S100
Truss Head Bolt (2 Req'd)
33
N804234-S2
Screw
34
266A74
Rear Door Latch Actuator Retainer
35
24630
Rear Door
36
26552
Rear Door Latch Control Escutcheon
A
—
Tighten to 21-29 Nm (16-21 Lb-Ft)
B
—
Tighten to 10-13 Nm (89-115 Lb-In)
C
—
Tighten to 7-8 Nm (62-70 Lb-In)
D
—
Tighten to 26-34 Nm (20-25 Lb-Ft)
E
—
Tighten to 3-4 Nm (27-35 Lb-In)
i need a wiring diagram for a 1961 lincoln continental, also a vacuum diagram will be helpful...
(More)
i need a wiring diagram for a 1961 lincoln continental, also a vacuum diagram will be helpful thanks, Dusty
How can I change the dashboard bulb illuminating the PRNDD1 shifting indicator, just above stearing...
(More)
How can I change the dashboard bulb illuminating the PRNDD1 shifting indicator, just above stearing column? What bulb # do I need? The owner's manual does not indicate a replacement bulb. Also, how do I access the bulb to change it?
Was clicking behind driver dash when running, now does nothing when you go to turn it over. Has...
(More)
Was clicking behind driver dash when running, now does nothing when you go to turn it over. Has lights and a new battery.