I'm replacing the head gasket on a 1988 Pontiac Grand Am 2.0 lit

Question edited for clarity.
Question moved to model category.

In the link

https://www.google.com/search?q=1997+Pontiac+Grand+Am+3.1+V6.+I+need+cylinder+head+gasket+bolts+torque

..

Says here

https://www.2carpros.com/questions/sequence-to-tighten-head-bolts-and-rocker-arms-also-torque-specs

https://www.google.com/search?q=torque+spec+for+a+2003+Pontiac+Grand+AM+3.4+head+gasket+bolts

..

I need know the torque head Pontiac Grand am se 1999. Machine 2.4

Head Bolts
Torque sequence --------- ' 6 2 3 7 ' ' 5 1 4 8 ' --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation.New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.Always coat bolt threads with the proper sealant.
The Intake Bolt Torque 10 Foot pounds (Final torque)
Note:to torque bolts & nuts, start in center using crisscross pattern working outward

first round is at 22lbs, second 44lbs, third 66lbs. make sure you get the order in which the bolts need to be tightened as not to warp the cylinder head, and that sequence is in the package your new head gasket (s) came in. If you cant find it, your local garage will photocopy it for you.

It is actually 10 ft lbs. This is something that you want to tighten to exact specs.


Hope this helps!

firstly tighten in sequence to 20Nm all round, then tighten to 30Nm all round,then tighten 90 degrees all round, and finally tighten a further 90 degrees all round. if you taken head off you should replace gasket or just use gasket sealer if you cant replace, just replace the head bolts, dont reuse or they may break

35ft pounds.

1st u must use all new head bolts, that said follow this factory procedure from the manual.
HEAD BOLT TORQUE FOOT POUNDS (FINAL TORQUE) TORQUE SEQUENCE --------- | 6 2 3 7 | | 5 1 4 8 | --------- STEP 1: TORQUE IN SEQUENCE TO 33 FT/LBS STEP 2: TURN AN ADDITIONAL 90 DEGREES RECHECK FINAL TORQUE IN SEQUENCE *** CAUTION *** ENGINE USES TORQUE TO YIELD HEAD BOLTS (TTY) THAT PERMANENTLY STRETCH DURING THE INITIAL INSTALLATION. NEW HEAD BOLTS MUST BE USED WHEN CYLINDER HEAD IS REPLACED OR RE-INSTALLED TO OBTAIN PROPER TORQUE. ALWAYS COAT BOLT THREADS WITH THE PROPER SEALANT

Head Bolt Torque For your 1994 Oldsmobile Cutlass Supreme (3.4L SFI DOHC): Foot pounds (Final torque) Note: Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque. Foot pounds (Final torque) Note: Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.