Low idle low power and hesitating,no fault codes

HYUNDAI OBDII DTC

P1100 Manifold Absolute Pressure Sensor Range/Performance
P1102 Manifold Absolute Pressure Sensor Circuit Low Input
P1103 Manifold Absolute Pressure Sensor Circuit High Input
P1123 Lang Term Fuel Trim Adaptive Too Lean
P1124 Long Term Fuel Trim Adaptive Too Rich
P1127 Long Term Fuel Trim Multiplier Too Rich
P1128 Long Term Fuel Trim Multiplier Too Lean
P1134 HO2S Bank 1 Sensor 1 Transition Time Switch (Bank 1 Sensor I)
P1154 HO2S Bank 2 Sensor 1 Transition Time Switch (Bank 2 Sensor 1)
P1166 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 1)
P1167 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 2)
P1168 HO2S Bank 1 Sensor 1 Heater Power Incorrect (Bank 1 Sensor 2)
P1169 HO2S Bank 1 Sensor 1 Heater Power incorrect (Bank 2 Sensor 2)
P1372 Segment Time Incorrect
P1400 Manifold Differential Pressure Sensor Circuit
P1440 EVAP System Vent Solenoid Circuit
P1443 EVAP System Fault (Fuel Tank Cap Missing)
P1510 Idle Control Valve Opening Circuit Shorted (Coil 1)
P1511 Idle Control Valve Command Signal Shorted (Coil 2)
P1513 Idle Air Control Valve Opening Coil Circuit Open (Coil 1)
P1521 Power Steering Switch Input Circuit
P1529 Customer Snapshot Request VIA CAN
P1552 Idle Air Control Valve Closing Coil Circuit Shorted
P1553 Idle Air Control Valve Closing Coil Circuit Open
P1586 Encoding Signal Circuit Not Rationale
P1602 Serial Communication Fault with Transmission Control Unit
P1605 Rough Road Sensor Circuit
P1606 Rough Road Sensor Circuit Not Valid
P1611 MIL Request Signal Circuit Low Input
P1613 ECU Self-Test Failed
P1614 MIL Request Signal Circuit High Input
P1616 Main Relay Fault
P1623 Diagnostic Lamp Power Stage Fault
P1624 MIL On Request Signal//Cooling Fan Relay Low Circuit
P1625 Cooling Fan Relay High Circuit
P1665 Power Stage Group 'A' Fault
P1670 Power Stage Group 'B' Fault

P0300 - Random, Multiple Cylinder Misfire Detected Fault Code Definition

• Random, Multiple Misfire Detected

Symptoms

• Check Engine Light flashing
• Rough running, hesitation, and/or jerking when accelerating
• In some cases, there may be performance problems, such as dying at stop signs or rough idling, hesitation, misfires or lack of power (especially during acceleration), and a decrease in fuel economy

Common Problems That Trigger theP0300

• Worn out spark plugs, ignition wires, coil(s), distributor cap and rotor (when applicable)
• Incorrect ignition timing
• Vacuum leak(s)
• Low or weak fuel pressure
• Improperly functioning EGR system
• Defective Mass Air Flow Sensor
• Defective Crankshaft and/or Camshaft Sensor
• Defective Throttle Position Sensor
• Mechanical engine problems (i.e.-low compression, leaking head gasket(s), or valve problems

run fault codes and fix sensor indicated to be faulty.

run the fault codes . Check for idle speed sensor and MAF sensor. It should be idling around 900rpm and the oil light coming on ( assuming you have enough oil in the sump) will be because of the very low idle rpm not pumping enough oil to maintain pressure.

Low power:
1. Spark plugs.
2. Fuel pump control circuit.
3. Ignition system.
4. Injectors.
5. Mass air flow sensor.
6. Variable valve timing system.
7. Engine compression.
8. Back pressure.

Could be dirty throttle body or needs tune up.fuel filter,air filter.

iam posting the hyundai code list i have that the vehicle manufacturer lists

P1100 Manifold Absolute Pressure Sensor Range/Performance

P1102 Manifold Absolute Pressure Sensor Circuit Low Input

P1103 Manifold Absolute Pressure Sensor Circuit High Input

P1123 Lang Term Fuel Trim Adaptive Too Lean

P1124 Long Term Fuel Trim Adaptive Too Rich

P1127 Long Term Fuel Trim Multiplier Too Rich

P1128 Long Term Fuel Trim Multiplier Too Lean

P1134 HO2S Bank 1 Sensor 1 Transition Time Switch (Bank 1 Sensor I)

P1154 HO2S Bank 2 Sensor 1 Transition Time Switch (Bank 2 Sensor 1)

P1166 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 1)

P1167 HO2S Bank 1 Sensor 1 Controller Adaptive Diagnosis Fault (Bank 2)

P1168 HO2S Bank 1 Sensor 1 Heater Power Incorrect (Bank 1 Sensor 2)

P1169 HO2S Bank 1 Sensor 1 Heater Power incorrect (Bank 2 Sensor 2)

P1372 Segment Time Incorrect

P1400 Manifold Differential Pressure Sensor Circuit

P1440 EVAP System Vent Solenoid Circuit

P1443 EVAP System Fault (Fuel Tank Cap Missing)

P1510 Idle Control Valve Opening Circuit Shorted (Coil 1)

P1511 Idle Control Valve Command Signal Shorted (Coil 2)

P1513 Idle Air Control Valve Opening Coil Circuit Open (Coil 1)

P1521 Power Steering Switch Input Circuit

P1529 Customer Snapshot Request VIA CAN

P1552 Idle Air Control Valve Closing Coil Circuit Shorted

P1553 Idle Air Control Valve Closing Coil Circuit Open

P1586 Encoding Signal Circuit Not Rationale

P1602 Serial Communication Fault with Transmission Control Unit

P1605 Rough Road Sensor Circuit

P1606 Rough Road Sensor Circuit Not Valid

P1611 MIL Request Signal Circuit Low Input

P1613 ECU Self-Test Failed

P1614 MIL Request Signal Circuit High Input

P1616 Main Relay Fault

P1623 Diagnostic Lamp Power Stage Fault

P1624 MIL On Request Signal//Cooling Fan Relay Low Circuit

P1625 Cooling Fan Relay High Circuit

P1665 Power Stage Group 'A' Fault
P1670 Power Stage Group 'B' Fault

That might be the answer if your truck had points. Points have not been used in automomotive ignition systems since the late 70s. The maintenance schedule for your vehicle does recommend replacement of the fuel filter, spark plugs. distributor cap, distributor rotor, and ignition wires every 60,000 miles. Hesitation can also be caused by a dirty Throttle Body bore. If the Check Engine light is coming on, I would recommend having your Engine Control Module scanned for fault codes and if any fault codes are present,have the code/codes properly diagnosed before replacing any parts.

and what is he bpt?? what does that refer to?

run the fault codes
indicates an idle control sensor or other throttle / accelerator sensors