Change headlight assembly - 2002 Suzuki Esteem

These videos _should_ help you. I haven't viewed them, but the wording is right.

https://www.google.com/search?q=change+the+headlight+assembly+on+a+2000+Lincoln+Navigator

..

1 Remove the front grill.


2 Remove the screws that secure the headlight assembly to the vehicle.


3 Unplug the wiring from the back of the headlight assembly. Then, gently pull the old headlight assembly from the vehicle and set it aside.


4 Replace the headlight assembly by inserting the new assembly into place and replacing the screws.


5 Insert the grill back into place and replace the screws to hold it in place.


From Chinasiony Electron

HEADLIGHT REPLACEMENT

1. Remove the front bumper
2. Disconnect the connectors (A).
3. Remove the 5 mounting bolts (B), then remove the headlight assembly (C).

Fig. 21: Removing Mounting Bolts & Headlight Assembly

1. Open the hood and remove the screws holding the headlight assembly in place. These screws are located on the back side of the headlight assembly.

2. Slide the headlight assembly forward.


3. Unplug the electrical connector running to the headlight ballast.


4. Slide the new headlight assembly and bulb into place, connect the connector to the headlight ballast and secure the assembly with the factory screws.

Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

lift hood, and on top of headlight assembly there are two plastic slide pins on top of headlight assembly to hold assembly in, just pull up on the two pins, when assembly is loose and will come out. now you can change your headlights. when putting back on, push in on headlight assembly, and push the pins back down.

1. Remove headlight mounting bolts and nut
2. Remove assembly
3. Install headlight assembly (with new bulb)
4. Replace/tighten headlight mounting bolts and nut

1. 
   

Yes, you can. Just take off the front grill, and the
headlights assembly. Don't tinker with the head-
light assembly adjusting nut, as this would change your headlight level. Take headlight bulb
off and change it. Replace the headlight, then, the
grill, and it's done.

There is one 10mm Bolt on the top of the light and three 10mm nuts on the back of the light. You will need to use a 10mm wrench to remove the nuts because they are in a tight place.

After the 1 bold and 3 nuts are removed, the entire headlight assemble will pull straight out. You don't need to take the headlight bulb out because there should be enough wire to pull out the assembly far enough to get to the turn signal bulb. This will allow you to change the turn signal bulb which should be a 4157 amber bulb.

When putting the headlight assemble back in the van, there is a plastic pin in headlight assembly that goes into a hole in the front fender for alightment. Don't force the light. Take your time and the headlight assembly will go back in the van smoothly.

You need to remove the bumper assembly to remove the headlight.