At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
You'll need to remove screws that are by the door handle,
arm rest, under door and side of door and then gently pull back on the
panel as there will also be retaining clips attached and you don't want
to break them. If needed, you can pull back the weather seal
(can't reuse it, but it's not that important) and you will be able to
access everything inside the door
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Jaguar 2000-06 - Locks & Lock Systems Power Door Locks - Removal & Installation
Door Lock Switch Door Lock Diagnosis & Testing
Visually inspect the following:
Misaligned door(s), hood or luggage compartment lid
Door latches
Actuating rod
Exterior door handle
Interior door handle
Door lock cylinder
Cable
Luggage compartment lid exterior release switch
Fuse(s)
Wiring harness
Electrical connector
Door lock actuator
Remote transmitter batteries
Vehicle battery
Remote transmitter
Door lock switch
Front electronic module
If an obvious cause for an observed or reported concern is found,
correct the cause (if possible) before proceeding to the next step.
Door Lock Motor Coupe And Convertible
Turn ignition key to position II.
Motor door glass to fully raised position.
Turn ignition key to position O.
Disconnect the negative battery cable.
Remove door casing for access.
Remove door water shedder.
Position PVC secondary water shedder for access.
Slacken and remove the door glass rear runner lower securing screws.
Reposition door glass rear runner. Mark the position of the glass rear runner upper securing screw.
Slacken and remove the upper securing screw and move the runner away from the glass.
Disconnect door handle and lock barrel (driver door only) operating rods from latch links.
Slacken and remove the three latch assembly securing screws and position latch for access.
Remove latch motor harness multiplug from mounting bracket and disconnect multiplug.
Release operating cable from door handle. Move inner door handle
to the locked position. Remove operating cable outer abutment from
support bracket. Disconnect cable inner from door inner handle.
Remove lock motor assembly from door.
To install, reverse removal procedure.
Fig. Removing door lock actuator
Sedan
Remove the door window glass
Detach the interior door handle.
Detach the actuator remote cable from the interior door handle.
Remove the interior door handle.
Detach the door window glass run.
Remove the exterior door handle retaining screws.
Remove the front door actuator retaining screws.
Reposition the front door actuator and exterior handle.
Remove the front door actuator and exterior handle.
Disconnect the front door actuator remote cable.
Detach the door lock cylinder connecting rod (1).
Detach the exterior door handle connecting rod (2).
SECTION 501-01: Body System — Interior
2004 F-150 Workshop Manual
REMOVAL AND INSTALLATION
Procedure revision date: 02/17/2004
Front Door Trim Panel Printable View (229 KB)Removal and Installation NOTE: LH side is shown. RH side is similar.
You will need to remove the interior door panel,put the glass in the full up position,remove the rod attached to the handle(small plastic clip),using a 10mm socket and extension with ratchet remove the 2 bolts and remove handle.
remove interior door panel(need special tool to pop plastic clips holding panel to door)with panel off remove plastic film,with window up you should be able to see two 10m nuts-bolts to remove-also have to pop lever off that goes down to door latch
Order the exterior door handle AND the clip that attaches the rod to the exterior handle from your local dealership ( any part in the salvage yard will have at least as much wear as the one U are replacing ) Also order a can of touch up paint matching your car. After you have the parts and have painted the new exterior handle, roll down the window and remove the interior door panel. ( instructions have been posted at 'replace door lock buttom' ) Two nuts, one on each side, hold the broken handle in place and must be removed ( DON'T loose them ). Loosen the rod from the clip at the top to allow a bit more room, But take note on the way it is attached ( you will need to reattach the rod to new handle ) To install new mechanism put the new clip on the rod, carefully place the gasket and the new handle in place and install nuts to secure. Test the door handle and make sure it works. Reinstall interior door panel.
Exterior Mirror
Removal and Installation All vehicles
NOTE: Left side exterior mirror shown, right side similar. Remove the interior door trim panel. For additional information, refer to Section 501-05 .
Front Door Trim Panel
Removal and Installation
Disconnect the battery ground cable. For additional information, refer to Section 414-01 .
Remove the inside door handle bezel from the trim panel.
Remove the window switch assembly.
Disconnect the window switch and power door lock electrical connectors.
Remove the upper trim panel screw at the window switch opening.
Remove the lower trim panel screws.
CAUTION: To avoid damage to the door trim panel, do not pull directly outward for this step. Lift the door trim panel by pulling directly upward on the armrest to disengage the panel clips.
Disconnect the power mirror electrical connector.
Remove the trim panel.
Remove the weather shield.
Vehicles with power, heated or approach lamp equipped exterior mirrors
remove door panel.. inside door you will see a rod going to the handle..on the end is a clip ..push the clip up off the rod .slide the rod out..remove 2 ..13mm nuts from handle ..remove handle
You have to remove the door panel, if you have roll down windows the handle will have to be removed. After panel is removed you have to drill the one rivet that hols the interior handle. slide the handle down and unfasten the rod retaining clip. Please make sure you do not break the clip. Install the new interior door handle, clip and provided fasteners. Try the door before you install the interior door panel, Note the is a good time to lube the window roller and the door mechanism. Make sure to install the water shield to provide the protecting from the elements. Line all the plastic retaining clips and or replace if they are broken. Good Luck.
×