How to locate heated oxygen sensor bank 1 sensor 1

bank one is left side top of engine standing looking at it , O2 sensor is located on exhaust manifold there is one on each manifold (right-left)

bank 1 is the front bank closest to the grill
sensor 1 is the heated oxygen sensor and is located in the manifold or before the cat converter
sensor 2 is the oxygen sensor and is located after the cat converter
get a specialist oxygen sensor tool so that the small wires are not damaged during repalcement

Four .
Heated Oxygen Sensor (HO2S Bank 1 Position 1)
Located in RH front pipe of the exhaust catalytic converter
--
Engine Controls Connector End Views in Engine Controls
Heated Oxygen Sensor (HO2S Bank 1 Position 2)
Located in RH rear pipe of the exhaust catalytic converter
--
Engine Controls Connector End Views in Engine Controls
Heated Oxygen Sensor (HO2S Bank 2 Position 1)
Located in LH front pipe of the exhaust catalytic converter
--
Engine Controls Connector End Views in Engine Controls
Heated Oxygen Sensor (HO2S Bank 2 Position 2)
Located in LH rear pipe of the exhaust catalytic converter

Bank 1 is located towards the driver's side. Sensor 1 is located upstream just below the exhaust manifold.
EOBD II Error Code: P0134
Description:
Oxygen Sensor (O2S) 1, Bank 1/Heated Oxygen Sensor (HO2S) 1, Bank 1 - No Activity Detected
Possible Causes:
- Wiring.
- Signal wire between the Heated Oxygen sensor and ECM is disconnected.
- Heated Oxygen Sensor defective.
- ECM.

P0050 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 1)

P0051 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 1)

P0052 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 1)

P0053 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 1)

P0054 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 2)

P0055 HO2S Heated Oxygen Sensor -Resistance (Bank 1 Sensor 3)

P0056 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 2)

P0057 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 2)

P0058 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 2)

P0059 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 1)

P0060 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 2)

P0061 HO2S Heated Oxygen Sensor -Resistance (Bank 2 Sensor 3)

P0062 HO2S Heated Oxygen Sensor -Control Circuit (Bank 2 Sensor 3)

P0063 HO2S Heated Oxygen Sensor -Control Circuit Low (Bank 2 Sensor 3)

P0064 HO2S Heated Oxygen Sensor -Control Circuit High (Bank 2 Sensor 3)

P0065 Air Assisted Injector -Range/Performance

P0066 Air Assisted Injector -Circuit Malfunction or Circuit Low

P0067 Air Assisted Injector -Circuit High

P0068 (MAP) Manifold Absolute Pressure /(MAF) Mass Air Flow - Throttle Position

Correlation

P0069 (MAP) Manifold Absolute Pressure / (BARO)Barometric Pressure Correlation

P0070 Ambient/Outside Air Temperature Sensor -Circuit Malfunction

P0071 Ambient/Outside Air Temperature Sensor -Range/Performance Problem

P0072 Ambient/Outside Air Temperature Sensor -Circuit Low Input

P0073 Ambient/Outside Air Temperature Sensor -Circuit High Input

P0074 Ambient/Outside Air Temperature Sensor -Circuit Intermittent

P0075 Intake Valve Control Solenoid Circuit Malfunction (Bank 1)

P0076 Intake Valve Control Solenoid Circuit Low (Bank 1)

P0077 Intake Valve Control Solenoid Circuit High (Bank 1)

P0078 Exhaust Valve Control Solenoid Circuit Malfunction (Bank 1)

P0079 Exhaust Valve Control Solenoid Circuit Low (Bank 1)

P0080 Exhaust Valve Control Solenoid Circuit High (Bank 1)

P0081 Intake valve Control Solenoid Circuit Malfunction (Bank 2)

P0082 Intake Valve Control Solenoid Circuit Low (Bank 2)

P0083 Intake Valve Control Solenoid Circuit High (Bank 2)
P0084 Exhaust Valve Control Solenoid Circuit Malfunction (Bank 2)

Hi there,

P0030 = HO2S Heater Control Circuit (Bank 1 Sensor 1) - No.1 Heated Oxygen sensor on bank 1.
P0036 = HO2S Heater Control Circuit (Bank 1 Sensor 2) - No. 2 Heated Oxygen sensor on bank 1

For both of these to trigger on the same bank, means most likely an Open or Short to Ground condition (somewhere on the Bank 1 circuit) stopping the HO2 sensors from reaching their working temperature.

Check the following in this order:

1) Using a multimeter, check 'continuity' of the Oxygen circuit FUSE terminals (don't rely on visual inspection alone) or replace fuse with a known good one.
2) Check for moisture getting into both oxygen sensor connector terminals (bank 1).
3) Check for good connection at Oxygen sensors (bank 1).
3) Have both heated oxygen sensors on Bank 1 tested (ensure their values are to specification).
4) Check HO2 pin-outs of the PCM for correct voltage.

Only replace the HO2 sensors as a last resort (if out of spec).

Then engine department relay centre & fusebox location is behind the washer bottle, but I believe the HO2 sensors are connected direct to the PCM, not a relay.

Cheers,


"If this has helped you in any way, please rate this solution"

The bank has to do with which side of the engine. The 'Sensor 1' indicates that it is upstream of the catalytic converter.

Heated Oxygen Sensor Removal & Installation Heated Oxygen Sensor (Front) (2.4L)

Heated Oxygen Sensor (Rear) (2.4L)

Heated Oxygen Sensor (Bank 1/Sensor 1) (3.3L)

Heated Oxygen Sensor (Bank 1/Sensor 2) (3.3L)

Heated Oxygen Sensor (Bank 2/Sensor 1) (3.3L)

Heated Oxygen Sensor (Bank 2/Sensor 2) (3.3L)

http://helpforcars.net/obd_codes/codes.php?code=P0037

It's an O2 sensor according to the above link, and it is bank 1 sensor 2 low, the 2 meaning that it is downstream past the catalytic converter but not on the manifold.

- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit open shorted to ground
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit poor electrical connection
- Faulty Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit
- Heated Oxygen Sensor (H2OS) Bank 1 Sensor 2 circuit fuse
- Faulty Engine Control Module (ECM) Possible Solution Tech Notes The code means that there is a problem with the heater element circuit of the heated oxygen sensor. Water getting inside the heated oxygen sensor connector can caused the heated oxygen sensor fuse to blow, which is a very common problem for this type codes. Before replacing the sensor, check for the condition of the heated oxygen sensor fuse and connectors.
Good luck on this repair.

Fig. Heated Oxygen (HO2S) location (sensor 1)-2.4L engine



Fig. Heated Oxygen (HO2S) location (sensor 2)-2.4L engine



Fig. Heated Oxygen (HO2S) location (bank 1, sensor 2) (bank 2, sensor 2)-2.7L engine



Fig. Heated Oxygen (HO2S) location (bank 2, sensor 1)-2.7L engine

I hope help you with this (rated this help). Good luck.

P0016 - Crankshaft Position Camshaft Position Correlation Bank 1 Sensor A
P0030 - Heated Oxygen Sensor (H02S) Heater Control Circuit Bank 1 Sensor 1
P0031 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 1 Sensor 1
P0032 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 1 Sensor 1
P0036 - Heated Oxygen Sensor (HO2S) Heater Control Circuit Bank 1 Sensor 2
P0037 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 1 Sensor 2
P0038 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 1 Sensor 2
P0050 - Heated Oxygen Sensor (HO2S) Heater Circuit Bank 2 Sensor 1
P0051 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 2 Sensor 1
P0052 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 2 Sensor 1
P0053 - HO2S Heater Resistance Bank 1 Sensor 1 (PCM)
P0054 - HO2S Heater Resistance Bank 1 Sensor 2 (PCM)
P0056 - Heated Oxygen Sensor (HO2S) Heater Circuit Bank 2 Sensor 2
P0057 - Heated Oxygen Sensor (HO2S) Heater Circuit Low Voltage Bank 2 Sensor 2
P0058 - Heated Oxygen Sensor (HO2S) Heater Circuit High Voltage Bank 2 Sensor 2
P0068 - Throttle Body Airflow Performance (PCM)
P0100 - MAF Sensor Circuit Insufficient Activity