Question about Cars & Trucks

Open Question

How do I change the worm drive in my TEC 3000 Hoist

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The driving modes don't work on my nissan juke n tec 1.6 petrol, there is no difference between the modes.


What have you done to check the driving modes Mark. Sometime all that changes is the shift points on the transmission so it will only show up if you accelerate hard.

Jul 04, 2017 | Nissan Cars & Trucks

1 Answer

I have a 2012 Mazda 2. Sitting on the road and turning the steering wheel 90 degrees right and left it makes a clunking noise. Put up on a hoist and doing the same it makes no noise. What is it.


the noise is generated by the weight on the points that are turning
the hoist you should be using is a 4 post hoist that the car drives on and the wheels are still on the hoist
any hoist that leaves the wheels dangling in the air will not be suitable to find the fault
most likely a steering ball joint end , suspension ball joint or failed suspension rubber mount

Mar 18, 2017 | Mazda Cars & Trucks

2 Answers

O/D Light is blinking and car has low revolutions when speeding up. Does not shift gears or go fast.


Stay off the highway and save your money for another car. Transmission rebuild will be $3000. Turn the OD off every time you start it. If you have a switch for it.

Jul 27, 2015 | 1989 Toyota Camry

1 Answer

Replace the altinator in a2007 Suzuki reno


wow, you want super basic service questions. even placement.
what country
which engine, ?
1.4 L E-TEC I4 (petrol)
1.6 L E-TEC I4 (petrol)
1.8 L Family II I4 (petrol)
2.0 L Family II I4 (petrol)
2.0 L RA 420 I4 (diesel)

try reading the manual.
pull the battery negative lug first. or boom.
I will never tell you how to jack a car ,not me.... read a book first.
read the FSM pages on Safety.....

https://suzukipitstopplus.com/Products/1068-2007-forenza-reno-service-manual.aspx


the steps are the same on all cars.
only access to ALT varies.
all cars made.
  1. neg lug off
  2. gain access
  3. unbolt wires at alt
  4. release belt
  5. unbolt alt.
the FSM may tell you the best way to gain access.

no engine stated, so I pass on details.

Oct 08, 2014 | 2007 Suzuki Reno Hatchback

1 Answer

4 wheel drive won't engage on hte hoist


I would put it in 4x4 before or as you bring it in the bay to get it to lock in 4x4.All the wheels need to role at the same time in order for it to go into 4x4.

Mar 09, 2010 | 2002 GMC Envoy

1 Answer

CAR DIES AT 3000 RPM


change the dist.coil pack and electrnic spark control module autozone 135.99 control module 31.99 for coil pack each

Nov 24, 2008 | 1997 Pontiac Firebird

1 Answer

Manual tranmission


your syncronizers are out

Aug 15, 2008 | 1999 Daewoo Nubira

1 Answer

How do i cange a clucth on a 1.5 honda non v tec


Basic socket and wrench set, metric of course. Screw drivers, pliers, etc. You'll need a 32mm socket to remove the large bolt at the end of the cv axle with a breaker bar. This bolt is usually pretty tight. I use an engine hoist and chain to top of trans. and lower it down. It saves your back. You'll have to remove both axles. Be sure you have a 6 in and 3 in 3/8 adapters for your sockets. This will make life easier too.

Jun 23, 2008 | 1995 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

67 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...