Question about BMW 325

Open Question

Fuel pressure regulator vacuum line diagram bmw e32

Posted by Anonymous on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Ajkill
  • 2035 Answers

SOURCE: 1997 S-10 fuel line/fuel pressure regulator

Please this link :

http://www.autozone.com/addVehicleId,2336303/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c152800bfe20

Posted on Jul 08, 2008

Ad
hasbensystem
  • 63 Answers

SOURCE: fuel pressure regulator

How do you know that it is the regulator?
these 4.3 motors had a lot of trouble from 93 to 98, I know I had 2 of them.
What happened to mine was that the intake kept getting very carboned up. After I would clean it, the truck would run fine for about 5 or 6 months, then same thing.
Theres actually a class action lawsuit about this that I believe has been settled, you may have recourse if you bought it through a dealer. Good luck.You'll need it.

Posted on Dec 23, 2008

csmock132
  • 4669 Answers

SOURCE: fuel pressure regulator

Have you checked the fuel pressure? If it is high and fuel is not returning, the regulator is bad. If it is low and fuel is not returning, the pump is bad.

Posted on Mar 11, 2009

  • 92 Answers

SOURCE: fuel pressure regulator had no vacuum line connected

another engineers wet dream. think of it this way . what is normally in the intake when the engine is running.. answer vacume, hence the regulator gets its vacume without a hose connected to it as its already in a full time vacume chamber.no hose required . ps be carefull to seat the regulator and o rings securely into the housing befor you reattach the secureing metal clip.
good luck chris

Posted on Mar 23, 2009

  • 335 Answers

SOURCE: fuel leaking into vacuum line on fuel pressure regulator

If you have fuel on the vacuum side of the reg, that means the reg is leaking,causing a variaty of drivabiliy problems. Replacing this reg is very straight forward. Just add a little lube to the O-ring on the reg before installation. Good luck.
Yours Moe.

Posted on Apr 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fuel pressure 1998 jeep grand cherokee 4.0 L V6


You should have a test port on the Fuel Supply rail, use a tool from a local auto parts "Tool Loaner program" where you can borrow tools for free,w/a deposit of course,then follow the steps provided;

MPI Fuel System Pressure Test

The MPI fuel system used in vehicles equipped with a 4.OL engine employs a vacuum balanced pressure regulator. Fuel pressure should be approximately 55-69 kPa (8-10 psi) lower with the vacuum line attached to the regulator than with the vacuum line disconnected. System fuel should be 214 kPa (31 psi) with the vacuum line connected to the regulator and 269 kPa (39 psi) with the vacuum line disconnected. CAUTION: Some fuel may be discharged when connecting fuel gauge to fuel rail.
  1. Connect a 0-414 kPa (0-60 psi) fuel pressure gauge to test port pressure fitting on fuel rail (Fig. 7).
  2. Remove vacuum line from pressure regulator.
  3. Start the vehicle.
  4. Note gauge reading. With vacuum line disconnected, fuel pressure should be approximately 269 kPa (39 psi).
  5. Connect vacuum line to pressure regulator. Note gauge reading. Fuel pressure should be approximately 214 kPa (31 psi).
  6. If fuel pressure is not approximately 55-69 kPa (8-10 psi) higher with vacuum line removed from regulator, inspect pressure regulator vacuum line for leaks, kinks or blockage. CAUTION: Fuel pressure will rise to as much as 655 kPa (95 psi) when the fuel return tine is pinched shut, shut engine down immediately after pinching oft fuel return line.
  7. If fuel pressure is low, momentarily pinch shut the hose section of the fuel return line. If fuel pressure remains low, inspect the fuel supply line, fuel filter, and fuel rail inlet for blockage. If fuel pressure rises replace fuel pressure regulator.
  8. If fuel pressure is above specifications, inspect the fuel return line for kinks and blockage.

Capacity Test

  1. Remove the cap from the pressure test port in the fuel rail.
  2. Connect a 0-414 kPa (0-60 psi) fuel pressure gauge to the pressure fitting on the fuel rail (Fig. 7).
  3. Start the vehicle. Pressure should be approxi- mately 214 kPa (31 psi) with the vacuum hose connected to the pressure regulator and 269 kPa (39 psi) with the vacuum hose removed from the pressure regulator.
  4. If the pressure is not to specification, check the following before replacing the fuel pressure regulator:
  • 4a - Inspect the fuel supply and return lines/hoses for kinks or restricting bends
  • 4b - Check the fuel pump flow rate. A good fuel pump will deliver at least 1 liter of fuel per minute with the fuel return line pinched off. If the fuel pump does not pump adequately, then inspect the fuel system for a plugged fuel filter or fuel pump inlet filter (sock). Fuel pump flow rate can be done by connecting one end of an old A/C gauge hose to the fuel test port on the fuel rail and inserting the other end of the hose into a container of at least 1 liter capacity. Run the fuel pump by installing a jumper wire into diagnostic connector terminals D1-5 and D1-6. Be sure to pinch off the fuel return line or most of the fuel will be returned to the fuel tank.

May 19, 2014 | 1996 Jeep Grand Cherokee

1 Answer

Vacuum routing


Here's a link,click on pitcher and it will enlarge and show you a list of parts.http://www.realoem.com/bmw/partgrp.do?model=BF73&mospid=47482&hg=16&fg=15

Nov 04, 2012 | 1999 BMW 323 Series

1 Answer

Vacuum diagram for a 2004 tiburon


There is only 4 vacuum lines on that engine

1- brake booster line

2- purge line to purge solenoid (top center of throttle body)

3- PCV hose. run straight from PCV to side of intake at base of throttle body

4- fuel pressure regulator line (short small diameter hose runs from #6 intake runner to fuel pressure regulator

5- tube that connects front cam cover to rear cam cover to improve vapor venting

http://www.hyundai-forums.com/attachments/gk-tiburon-coupe-s111-2003-2008/38204d1276396353-vacuum-lines-2004-tiberon-pict0001.jpg

Jun 25, 2012 | Hyundai Tiburon Cars & Trucks

1 Answer

Exhaust pipe is blowing out a mist of black smoke


BLACK EXHAUST SMOKE IS A RICH FUEL MIXTURE.CAUSE BY WEAK SPARK IGNITION, FAULTY MAP SENSOR CHECK MAP SENSOR VACUUM HOSE AND ELECTRICAL CONNECTOR BECAUSE BAD MAP SENSOR WILL CAUSE RICH FUEL MIXTURE CHECK THE VACUUM LINE GOING TO FUEL PRESSURE REGULATOR, MAKE SURE FUEL PRESSURE REGULATOR GETTING VACUUM AT VACUUM LINE IF NOT LOOK FOR BROKEN OR DISCONNECTED VACUUM LINE TO FUEL PRESSURE REGULATOR, CHECK FUEL PRESSURE REGULATOR VACUUM LINE IF YOU SEE GASOLINE IN VACUUM DIAPHRAM TO FUEL PRESSURE REGULATOR REPLACE FUEL PRESSURE REGULATOR,CHECK THE EVAP CANISTER IF GAS SOAK IT WILL CAUSE RICH FUEL MIXTURE.

Aug 05, 2011 | 1995 Chevrolet Blazer

1 Answer

I have a 2004 Tahoe which has misfire problems (P0300). I changed the plugs, wires, fuel filter and air filter but problem still exist. The 4 plugs on the passenger side continue to file out and become...


Removal & Installation of fuel Regulators on
4.8L, 5.3L & 6.0L Engine To Remove:
CAUTION
Three styles of fuel pressure regulators and fuel rails will be used in this model year. Each regulator has a different "footprint" that consequently changes the size of the receiving port in the fuel rail. The regulator retaining clips are specific to each rail-regulator design and cannot be interchanged.
chevy_aval15_02-04_fuelrail.gif

  1. Remove the engine sight shield.
  2. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure.
  3. Clean the fuel pressure regulator retainer and the surrounding area.
  4. Remove or disconnect the following:
    • Fuel pressure regulator vacuum line.
    • Fuel pressure regulator retainer.
    • Fuel pressure regulator.
  5. Remove the following parts from the fuel rail:
    • Backup ring (10)
    • Regulator Seal O-ring (11)
    • Regulator filter (12)
    • Regulator seal O-ring (13)
To Install:
chevy_aval15_02-04_retainer.gif

  1. Make sure the NEW fuel pressure regulator retainer is the right one.
  2. The tabs (1) are used on the straight vacuum port retainer (2), and the E85-straight vacuum port retainer (3).
  3. The angle vacuum port retainer (4) has no tabs. chevy_aval15_02-04_fuelrail.gif

  4. Install the following parts onto the fuel pressure regulator (9).
    • Backup ring (10)
    • Regulator seal O-ring (11)
    • Regulator filter (12)
    • Regulator seal O-ring (13)
  5. Lubricate the fuel pressure regulator O-rings with clean oil.
  6. Install the fuel pressure regulator and retainer. CAUTION
    Whenever the fuel pressure regulator is removed from the fuel rail NEW O-rings and a NEW retaining clip should be used on reinstallation.
  7. Connect the vacuum line.
  8. Tighten the fuel filler cap.
  9. Use the following to inspect for leaks:
    • Turn ON the ignition, with the engine OFF, for 2 seconds.
    • Turn OFF the ignition for 10 seconds.
    • Turn ON the ignition, with the engine OFF.
    • Install the engine sight shield.
8.1L Engine To Remove:
Fuel pressure regulator vacuum line gm_trk_sub15_fuel_press_reg_vac_line.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of thjs section
  2. Remove the fuel injector sight shield as needed
  3. Relieve fuel system pressure (See: Fuel Pressure Relieving)
  4. Disconnect the fuel pressure regulator vacuum line (A) 8.1L Fuel pressure regulator retainers gm_trk_sub15_81l_fuel_press_reg_retainers.gif

  5. Clean any dirt from the fuel pressure regulator retainer and the surrounding area
  6. Remove the fuel pressure regulator retainer (I)
  7. Remove the fuel pressure regulator (H) from the fuel pressure regulator housing
To Install:
8.1L Fuel pressure regulator retainers gm_trk_sub15_81l_fuel_press_reg_retainers.gif

  1. Install or connect the following:
    • Backup ring (J) on the fuel pressure regulator (H)
    • New large O-Ring (K) on the fuel pressure regulator
    • Regulator filter (L) on the fuel pressure regulator
    • New small O-Ring (M) on the fuel pressure regulator
  2. Lubricate the fuel pressure regulator large O-Ring and the small O-Ring with clean engine oil
  3. Push the fuel pressure regulator onto the regulator housing on the fuel rail
  4. Install a new fuel pressure regulator retainer (I)
  5. Install or connect the following:
    • Fuel pressure regulator vacuum line
    • Negative battery cable
  6. Tighten the fuel filler cap
  7. Inspect for leaks using the following procedure:
    • Turn on the ignition with the engine off for two seconds
    • Turn off the ignition for 10 seconds
    • Turn on the ignition with the engine off
    • Inspect for fuel leaks
  8. Install the fuel injector sight shield
  9. Road test the vehicle to check performance
prev.gif next.gif

Sep 02, 2010 | Chevrolet Tahoe Cars & Trucks

3 Answers

Where is the fuel pressure regulator located on 2.5l engine


FUEL PRESSURE REGULATOR IS ON FUEL RAIL WITH THE FUEL INJECTORS.THE FUEL PRESSURE REGULATOR ALSO HAS A VACUUM LINE GOING TO IT.THE FUEL INJECTORS AND FUEL PRESSURE REGULATOR IS UNDER THE INTAKE COVER.

May 21, 2010 | 1994 BMW 3 Series

1 Answer

Not getting enough fuel .will only go 5 mh and now will idle but stalls when you try to take off


CHECK FUEL PRESSURE IT SHOULD BE 41 TO 47 PSI. IF NOT REPLACE FUEL FILTER..IF DONT HELP FUEL PUMP BAD.IF FUEL PRESSURE GOOD.CHECK VACUUM LINE TO FUEL PRESSURE REGULATOR SHOULD BE GETTING VACUUM IF NOT FIX BROKEN VACUUM LINE TO PRESSURE REGULATOR.IF FUEL PRESSURE REGULATOR GETTING VACUUM THEN THE FUEL PRESSURE REGULATOR IT SELF IS BAD.

Mar 12, 2010 | 1999 Oldsmobile Alero

1 Answer

2001 dodge durango 4.7 fuel pressure flutters during idle


IF FUEL FILTER HAS BEEN REPLACED.FUEL PRESSURE REGULATOR IS GOING BAD OR NOT GETTING VACUUM.CHECK VACUUM LINE GOING TO FUEL PRESSURE REGULATOR.MAKE SURE ITS GETTING VACUUM.IF YOU SEE GAS IN VACUUM LINE TO REGULATOR.REPLACE FUEL PRESSURE REGULATOR.IF ALL IS GOOD FUEL PUMP GOING BAD.

Jan 24, 2010 | 2001 Dodge Durango

1 Answer

How do i put fuel pressure regulator in my 1994 BMW 325i


Fuel pressure regulator is located on the fuel rail. 1. Remove top engine covers and fuel rail mounting bolts. 2. Disconnect vacuum hose. 3. Remove regulator clamp, noting position of regulator. 4. Pull regulator out with shop towel (full of fuel) don't lose thrust washer behind. 5. Replace with new O-rings.

Jan 04, 2010 | 1994 BMW 3 Series

2 Answers

Vacuum lines


Hello, I have the 1993 Ford Festiva shop manual in front of me. The vacuum hose on the Fuel Pressure Regulator goes to the intake manifold. The manual says that the fuel pressure is maintained at a constant 36.3 psi, and when the engine vacuum drops (caused by high fuel demand) it causes the fuel pressure to increase inside the regulator. There should be a vacuum diagram on the bottom side of the hood that will help to show you what vacuum port on the manifold that it attaches to. If the decal is gone, look on the intake manifold for a vacuum port that is open and causing a vacuum leak. I hope this helps.

Oct 15, 2009 | 1993 Ford Festiva

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Frankie B

Level 2 Expert

65 Answers

Fred Sops

Level 2 Expert

272 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...