Question about 2004 Cadillac Deville

Open Question

Codes p0420 p0496 p0507 p2610 p1372 - 2004 Cadillac Deville

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2007 equinox Error code p0496 & p0420 are both coming up AND my speedometer and gas gauge and temp gauge started going crazy after these codes came up. I have only had this car 10 days.


These codes have nothing to do with instrument cluster !
DTC P0420: Catalyst System Low Efficiency Bank 1 , Catalytic coverter is bad ,
DTC P0496: Evaporative Emission System Flow During Non-Purge
Evap emissions purge solenoid is bad more then likely . Your best bet , take it back to where you got it .

Apr 26, 2017 | Chevrolet Equinox Cars & Trucks

1 Answer

Check the meaning of codes, for p0420 and p0496


P0420 Catalyst efficiency below threshold Bank 1.
P0496 Evap emission high purge flow fault

Mar 22, 2016 | 2010 Buick LaCrosse CXS

1 Answer

My Pontiac vibe 2006 is showing PO6006, PO6007 code does anyone ha be any idea what it means


P0606 , P0607 ! no such codes P06006 or P06007
DTC P0601, P0602, P0603, P0604, P0605, P0606, P0607, P1600, P1621, P1627, P1680, P1681, P1683, or P2610
DTC P0606 Control Module Internal Performance
The DTC P0606 and P2610 set when the powertrain control module (PCM) has determined that the control module has an internal fault. The PCM performs continuous self checks of all internal circuits. There are 2 central processing units (CPU) within the control module. If the outputs from the two CPUs deviates from the standard level, a DTC P0606 sets. The control module has several internal clock or timer circuits. The DTC P2610 diagnostic monitors the internal timer circuit responsible for the ignition OFF operation of the evaporative emission (EVAP) system vacuum leak pump. If the there is an error in the control module timer, a DTC P2610 sets.

Feb 25, 2016 | 2006 Pontiac Vibe

2 Answers

What is code p2610


"DTC P2610 is set if an internal ECM problem is detected.
1.With ignition OFF, remove both ECM connectors.
2.Wait at least one minute.
3. Replace the connectors making sure to completely seat and lock them.
4.Turn the ignition ON with the engine OFF, and clear the stored codes.Verify the MIL light turns OFF, and stays OFF. If the MIL light does not turn OFF, repeat the clear code command until it the MIL light remains OFF.
5.Turn OFF the ignition and leave it OFF for at least one minute.
6.Turn the ignition back ON with engine OFF and observe that the DTC does not reset.
If the DTC P2610 is still set, repeat Steps 1 through 6 one additional time. If Steps 1 through 6 still do not correct the DTC P2610, verify there is constant battery voltage to ECM Connector C1- terminal 77. (circuit 440 / orange wire) If battery voltage is not present on Connector C1- terminal 77, troubleshoot and repair the circuit."

Oct 27, 2014 | Kia Sedona Cars & Trucks

1 Answer

Code 2610, engine doesn't start same felling as if the battery too weak to prop up the engine


If a P2610 has been verified do not replace the ECM. Perform the following steps when encountering a P2610.

Turn the IGNITION OFF for 90 seconds. Unplug both the engine control module (ECM) connectors for 90 seconds. After 90 seconds has passed, re-install the ECM connectors. With the ignition on use the Tech2 and clear all codes in the ECM. This procedure should prevent future sets of the P2610. For 2006 and certain 2007 model vehicles, there may also be a calibration update available which addresses P2610 false sets.

Please follow this diagnostic or repair process thoroughly and complete each step. If the condition exhibited is resolved without completing every step, the remaining steps do not need to be performed.

Aug 07, 2013 | Chevrolet Optra Cars & Trucks

1 Answer

P2610 code aveo 2009


the code means this ECM/PCM INTERNAL ENGINE OFF TIME PERFORMANCE

Jan 24, 2013 | 2005 Chevrolet Aveo

1 Answer

2007 chevy colorado DTC code P2610


BEFORE ANY THING. CK YOUR CABLES TO THE PCM. TAKE THEM OUT AND PUT THEM BACK IN. ALSO, MAKE SURE MASS AIR FLOW CONNECTIONS ARE TIGHT.

Jan 11, 2012 | Chevrolet Chevy Cars & Trucks

1 Answer

I need the discription for code P1372 2002 Olds Intrigue


P1372 - Crankshaft Position Sensor Circuit Performance

Need to replace.

Sep 28, 2011 | 2002 Oldsmobile Intrigue

3 Answers

Code P0507


P0507-- idle speed high

Jun 02, 2008 | 2001 Chevrolet Impala

Not finding what you are looking for?
2004 Cadillac Deville Logo

Related Topics:

148 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...