a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need. goodluck!
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
To get at the speaker, you need to remove the rear window shelf trim panel -
Remove rear seat lower by lifting from front;
Remove bolts holding rear seat back and remove seat back; Remove the seat belt retractors;
Remove the push in retainers from the cross car beam;
Lift up on the front of the shelf panel to disengage the hook and loop material; then do the same at the rear of the panel, and pull out the shelf.
The speaker is now accessible for removal.
The rear seat is four (4) pieces.
You will need two tools a 6mm and 8mm wrenches. 1.) Unbuckle the rear seat belts. 2.) Locate the bolt in the center part of the rear seat, between the cushion and the seat-back. Remove the bolt with a 6 mm socket wrench. 3.) Push down firmly on the front edge of the rear seat cushion and pull it toward you to unhook and remove the rear seat cushion. Push the seat belt stalks through the center holes and lift the cushion out of the Accord. 4.) Pull the lever on the side of the rear seat bolster to lower the rear seat-back, which must be in the down position to access its bolts. 5.) Slide the center seat belt toward the passenger side of the vehicle. Move the loop over the edge of the seat-back to prevent it from hindering removal. 6.) Remove the three bolts from the bottom edge of the rear seat-back, using an 8 mm socket wrench. One bolt is in the center; the other two bolts are on either side. 7.) Pull the rear seat-back out of the Accord. The remaining sections of the seat should be the two side bolsters. 8.) Remove the bolts from the bottom of the side bolsters with a 6 mm socket wrench. Push firmly against the first side bolster. Push it upward to slide it out of its mount. Repeat the process on the bolster on the other side to finish removing the Accord's rear seat.
This should take approximately 15-30 minutes depending hoe mechanically inclined a person is.
According to the service manual for my 2006 VUE, 2 bolts in front and 5 bolts behind the rear seat is all you need to remove to get the whole seat out. Removal of any components of the rear seat always starts with "remove the rear seat assembly".
PUSH IN CENTER FRONT EDGE CUSHION TO DISENGAGE PART OF SEATS WIRE FRAME FROM CLIPS.WITH CLIPS UNHOOKED LIFT UP AND REMOVE SEAT.IF REAR SEAT NOT HELD IN PLACE WITH CLIPS. LIFT UP THE REAR SEAT CUSHION AND PIVOT IT FORWARD. DETACH THE RETAINING BOLTS AT THE LOWER EDGE OF THE SEAT BACK AND IF NECESSARY REMOVE THE SEAT BELT ANCHOR BOLTS.LIFT UP ON SEAT BACK REMOVE IT..
Be sure that your model has fold down rear seats...you should see the seperation around both rear seats...if equipped, the fold down release is located at the top corner of each rear seat...pull the lever up to release...if your model does not have the fold down option...you will need to remove the rear seat...remove the lower cushions first...look on the lower front of the seats for hold down bolts...second you will need to remove the top of the rear seat...hold down bolts are at the bottom of the top cushion...after removing the bolts (one each side) you need to push up on the cushion to remove...this will then allow access to the trunk...find the trunk latch and try to release by twisting the latch cable...Hope this helps...
Push the lower seat cushion toward the rear of the car and lift, there's 2 hooks approx. 12" or so either side of the center of the seat.
The seat back is held in with 2 bolt located on the lower outside corners.
You'll have to unbolt the seatbelts from the floor to completely remove the seat back.
Retractor and Tongue—Sedan
SPECIAL SERVICE TOOL(S) REQUIRED
Safety Belt Bolt Bit
T77L-2100A NOTE: Safety Belt Bolt Bit T77L-2100-A should be used for safety belt removal and installation.
Remove rear seat cushion. Refer to Section 01-10 .
Seat Cushion, Rear
Apply knee pressure to lower front portion of the rear seat cushion. Push rearward to disengage rear seat cushion pad and frame (600A88) from rear seat cushion front retainers (63370).
Remove rear seat cushion from vehicle.
Remove rear seat back. Refer to Section 01-10 .
Seat Back, Rear
60/40 Split Bench—Sedan Removal
NOTE: Safety belt bolts do not secure seat back to vehicle.
Remove rear seat cushion as described.
Fold down back seat and remove two bolts in the center of each seat back striker plates.
Remove two bolts from outboard rear seat back frame retaining brackets.
Lift seat back up and pull forward to remove from vehicle.
Remove panel (52018) and quarter trim panel (31012). Refer to Section 01-05 .
Trim Panel, Quarter—Sedan
Remove rear seat. Refer to Section 01-10 .
Pull up on rear section of rear door scuff plate that overlaps lower quarter trim panel.
Pull lower quarter trim panel away from body.
Remove safety belt retaining bolt.
Feed safety belt through lower quarter trim panel.
Remove safety belt anchor plate-to-sill bolt from quarter panel.
Remove retractor anchor nut and retractor from rear quarter panel.
Remove upper seat belt anchor bolt and anchor from upper rear quarter panel.
Slide anchor plate end of safety belt through the openings in the quarter trim panel.
Remove outboard front safety belt retractor and tongue (611B08) from the vehicle.
Bolt (Part of 611B68)
Upper Rear Quarter Trim Panel
Retractor and Tongue
Rear Quarter Panel (Part of Body)
Lower Rear Quarter Trim Panel
Mounting Stud (Part of Body)
Remove seat belt anchor bolt and retractor and tongue from rear deck panel.
To install, reverse Removal procedure.
Make sure the safety belt webbing is not twisted. If it is, remove the twist.
Tighten retractor anchor bolt and safety belt anchor plate-to-sill bolt to 34-46 Nm (25-33 lb-ft).
I think you have to remove headrst bfore folding seat back down. You may have to unbolt seat from floor. 4 bolts.
Rear Seat Backrest —Split Bench
Removal NOTE: The 40% rear seat backrest must be removed before the 60% rear seat backrest. 40% rear seat backrest
Remove the 40% rear seat backrest.
Remove the nuts and bolts.
Remove the backrest.
60% rear seat backrest
Remove the 60% rear seat backrest.
Remove the nut and bolt.
Remove the backrest.
Installation NOTE: The 60% rear seat backrest must be installed before the 40% rear seat backrest. 60% rear seat backrest
NOTE: Do not tighten the nut and bolt at this time. Install the 60% rear seat backrest.
Install the rear seat backrest.
Install the nut and bolt.
40% rear seat backrest
NOTE: Do not tighten the nuts and bolts at this time. Install the 40% rear seat backrest.
Install the rear seat backrest.
Install the nuts and bolts.
60/40% rear seat backrest
Tighten the 60/40% rear seat backrest nuts and bolts in the sequence shown.
40% Rear Seat Backrest
Tighten the 40% rear seat backrest nuts and bolts in the sequence shown.