Question about 1990 Oldsmobile Cutlass Ciera

Open Question

Torque specs for intake manifold on 1990 oldsmobile cutlass ciera

I need to find the bolt torque specifications for the intake manifold on a 1990 Oldsmobile Cutlass Ciera S V6.

Posted by on

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
ddegroote
  • 35 Answers

SOURCE: 1995 Oldsmobile Cutlass Ciera SL 2.2 head bolts

you have long bolts and short bolts, long bolts go in positions 1,4,5,8,9 - short bolts remaining positions, all long bolts go in back of engine, toward fire wall or front of dash, those are positions starting at passenger side to drivers side, 8,4,1,5,9, so 1 is in the center position, 9 on drivers side. short bolts in front, positions passenger side 7, 3, 2, 6,10, stud is in position 10. Tighten bolts in sequence, starting at 1, long bolts get 32Nm, short bolts get 29Nm, next pass torque all to 58NM, than final pass add an angle of 100 degrees, little more than 1/4 turn with wrench. Bolts should have 11.9 on head, the tightening specification is called a torque plus angle to yield, that is why in your gasket kit is tells you to replace the bolts, it is recommended. I know, because I am the GM Manager for fastening engineering. Hope this helps

Posted on May 29, 2009

Ad
  • 834 Answers

SOURCE: i need to reset the timing on my 93 oldsmobile

You must have an ignition distributor to be able to reset or change the engine timing. If you do have a coil pack then the engine timing is completely controlled by the computer and there is no timing adjustment.

Posted on May 10, 2010

  • 161 Answers

SOURCE: I just need to know

i am hoping that means a 2.3L if so it calls for 18ft/lbs.and bring all bolts snug then tighten or torque from middle out left side first then the right from middle out as well. hope this helps...please rate my answer an i sure hope this helps let me know...:~)thank you for using fix ya.

Posted on Apr 02, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Intake manifold torque specs 2000 olds silhoutte 3.4


Follow the link for a complete listing of this engines bolt torque specs. Torque Specs Database

Jan 25, 2017 | 2000 Oldsmobile Silhouette

1 Answer

98 ford windstar intake manifold torque specs


Intake torque specs ' FordForumsOnline.com

www.fordforumsonline.com > Ford Tech Forums > Engine & Drivetrain

May 7, 2010 - 2 posts - ‎2 authors
ISO torque specs for the intake & plenum for a 98 Windstar...3.8 with the ... Our community is here to help you with any questions you have related to your Ford. ... Lower Intake Manifold to Cylinder Head Bolt 8-12 - (71-106).

Torque Specifications - AutoZone

www.autozone.com/.../Ford-Windstar.../Specifications/Torque-...

AutoZoneAutoZone Repair Guide for your 2004 Ford Truck Ranger 2WD 2.3L MFI DOHC 4cyl Engine Mechanical Specifications Torque Specifications. ... Ford Windstar 1999-2003 ... Bolts, Main Bearing Bolts, Rod Brearing Bolts, Crankshaft Damper Bolts, Flywheel Bolts, Manifold. Intake, Exhaust ... Vehicle: 2008 Ford F150, 98 Civic.

Dec 21, 2015 | 1998 Ford Windstar

1 Answer

Bolt torque specifications for the intake manifold on a 1992 Oldsmobile Cutlass Ciera s v6 3.3 liter


Hi,with the inlet manifold as long as the two serfices are clean and the gaskets are being replaced,all you need to do is tighten all the bolts all the way home,right when you feel that the bolt is fully home then tihten it another quarter of a turn, then tighten every bolt this way and there wont be a problem.
I have never used torque settings for manifolds and never in my 30 years of working on cars had a problem with water leaks from the inlet maifold.
well hope this was some use to you all the best and good luck with the rest of the work you are doing.

Apr 17, 2015 | 1992 Oldsmobile Cutlass Ciera

1 Answer

3.5L oldsmobile intrigue intake manifold sequence and spec torque


The torque specification is a 2-step process;

Tighten the vertical lower intake manifold bolts (the four middle ones) to 7 Nm (62 lb in). Tighten the diagonal lower intake manifold bolts (two on each end) to7 Nm (62 lb in). Tighten the vertical lower intake manifold bolts (the four middle ones) to 13 Nm (115 lb in). Tighten the diagonal lower intake manifold bolts (two on each end) to 25 Nm (18 lb ft).


2009-05-15_194459_lower.gif

Oct 11, 2013 | Cars & Trucks

1 Answer

I just need to know the foot-lbs of torque needed to tighten down the intake manifold on a 1992 Oldsmobile Cutlass Ciera 3.3L


i am hoping that means a 2.3L if so it calls for 18ft/lbs.and bring all bolts snug then tighten or torque from middle out left side first then the right from middle out as well. hope this helps...please rate my answer an i sure hope this helps let me know...:~)thank you for using fix ya.

Apr 02, 2011 | Oldsmobile Cutlass Ciera Cars & Trucks

1 Answer

What are the lower intake manifold bolt torque sequence on a 98 oldsmobile intruige


When torqueing bolts on manifolds or heads you always start in the middle or center and torque in a circle motion and olny torque 1 bolt at a time. Start with a low toque and increase torque up 5 to 10ft lbs / or newtons each time until torque spec is reached.

Mar 14, 2010 | 1998 Oldsmobile Intrigue

2 Answers

Need l head bolt for cutlass ciera. l998


Go to your local GM dealer and ask for the head bolt you need. They will supply it for you

May 26, 2009 | 1995 Oldsmobile Cutlass Ciera

1 Answer

Need to replace intake gasket 1989 Oldsmobile Cutlass Ciera


I am doing intake gaskets right now on an expedition and you have to look carefully around and take your time and you will find what is holding you up from taking it out because nowhere in the book does it state you had to take the two bolts out for the thermastat housing on the expedition that I am working on you can also go to auto zone and they can give you a diagram because you will need the torque specs anyways

Dec 07, 2008 | 1989 Oldsmobile Cutlass Ciera

Not finding what you are looking for?
1990 Oldsmobile Cutlass Ciera Logo

Related Topics:

133 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8269 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...