Question about 2008 Ford Fusion

Open Question

Location of the pcv valve on a 2008 ford fusion

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 92 Answers

SOURCE: 1998 Ford Explorer sport 4.0L 4x2 PCV Valve Location

the pcv is located on the rear(firewall) of the drivers side valve cover.turn counterclockwise and pull to remove be careful there are 2 small tabs inside the pcv hole in the valve cover(can feel with small finger) this is to hold valve in place so it wont leak.if you have a oil leak at the pcv a quick fix is to put a small amount of silicone around the pcv o-ring and install.wait hours for silicone to set up.

Posted on Oct 21, 2008

  • 1 Answer

SOURCE: pcv valve :where is it located on a 1999 ford explorer sport 2wd

It is located at the back of the engine near the fire wall. It is gray with a T connector at the top with two hoses coming off of the T and going forward into the intake manifold.

Posted on Mar 07, 2009

  • 38 Answers

SOURCE: location of pcv valve on 1992 ford f150

Which engine??? 4.6 and 5.0 liter rear of passenger valve cover

Posted on Nov 28, 2009

mitchbtu
  • 121 Answers

SOURCE: Where is pcv valve located on 2005 taurus

It is below the egr valve close to the intake manifold below the intake air sensor, there is a tube running to it from the engine to recirculate exhaust air with fresh air, there is a clamp holding it to the air intake that you need pliers to remove, then you need to turn counter-clockwise 90 degrees to remove, do the reverse to install. to make it easier to access remove the upper intake. The pcv valve is not visible, however, you can identify it by the 3" inch long rubber hose that connects to the steel line running into the bottom of the intake. I have the part and am going to replace it soon, although Ford really makes it difficult to remove it -
pcv valve is located just under the throttle body. remove air cleaner assembly from throttle body and you will see a u shaped hose running horizontally.

Posted on Jan 27, 2010

ZX2Fast
  • 547 Answers

SOURCE: LOCATION OF PCV VALVE ON 2002 FORD ESCORT ZX2

Looking from the front of the car, start at the thermostat housing (where the top radiator hose goes) and go down from there. Located right next to the exhaust mannifold you'll see the hose going to the PCV valve.

Posted on Mar 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Were is the map sensor located on a 2008 ford fusion 4 Cyl


Try searching "map sensor location ford fusion" I got a number of hits that you may find useful. Try it!

Jun 16, 2015 | 2008 Ford Fusion

2 Answers

When shouldpcv be changed on 2008 ford edge


If you are able, get a original part and change it following the services / warranty list of parts, that the dealer change according the miles. If you buy the PCV in a regular auto store; more frecuently, maybe half the time. Hope this helps. Take care.

May 15, 2014 | 2008 Ford Edge

1 Answer

2008 Ford Fusion PCV Valve??


yes it has a 2 wire connector.

Jul 16, 2013 | Cars & Trucks

1 Answer

Rear brake cailpers won't collapse on 2007 ford fusion


Open bleeder valve & push caliper piston, in as
you rotate piston to screw in parking brake

Do this by hand,only use a clamp on the front calipers

Apr 08, 2013 | 2008 Ford Fusion

1 Answer

Location of pcv valve on 2008 ford taurus 3.5


On 3.5L engines, the PCV Valve is located on the rear valve cover (see pictures bellow). Please note: the PCV valve must be replaced if it's removed. Access to the valve is easier if you remove the upper intake manifold. However, this is not absolutely necessary and if you are already a little mechanically inclined you can do it the way you would replaced any other PCV valve.

    -A 19mm open wrench will make your life a lot easier if the PCV valve is a bit tight. It is in an awkward spot to apply pressure.

    -Disconnect the electrical connector from the valve. There is a small pin or locking device on the wire that you will have to slightly depress for the connector to release.

    -Disconnect the hose from the valve and turn the hose clockwise so that you have a bit of room to work with.

    -Turn the PCV valve counterclockwise and remove from the valve cover. Pay close attention to the position of the valve at the point when it is to be removed. The new PCV valve will go in at that same position. Why is this important? It is possible to install the PCV valve facing in the opposite direction. Once the PCV valve in and locked it in place, it damages the locking mechanism. Therefore, if you remove it you will have to throw it away and purchase a new one.

    -You just saved $130 - $150 to have the PCV replaced at the dealership...

location-pcv-valve-2008-ford-taurus-3-5-cgnwdhiy0mxwbb3xg5zhzgxj-5-0.jpg

Apr 07, 2013 | 2008 Ford Taurus SEL

2 Answers

Where is the pcv valve on a 2008 ford taurus


Rear of the engine (near the firewire) with a hose that connects it to the air intake. See this video @ 5:50 to see location and what the hose looks like.

https://www.youtube.com/watch?v=3150o821Aqg9ad4d62b-6106-4d01-ba03-1d30789715a5.jpg


Part #6A666 on motorcraft's website

Aug 05, 2012 | 2008 Ford Taurus Limited

1 Answer

I need to locate the air senor switch in a 2008 ford fusion


The mass air flow sensor is in the air intake tube at the lower left corner of the engine compartment. Please rate this info That will help me THankyou RJ

May 30, 2010 | 2008 Ford Fusion

1 Answer

PCV Valve location


It should sit in your valve cover. On the passenger side (if I remember correctly). It should be right on your valve cover with a line that attaches to the top of it.

May 05, 2009 | 2008 Hyundai Veracruz

2 Answers

Pcv valve location


it is normally located on the valve cover itself look for the black tube going into the top of the valve cover gasket

Feb 04, 2009 | 1999 Ford Windstar

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5501 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...