Question about 2010 Dodge Journey

Open Question

Brake bleeding sequence for 2010 dodge journey

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

emissionwiz
  • 75822 Answers

SOURCE: whats the code so the doors don't lock on a 2010

still don't understand what code u are referring to ? you can disable the auto-lock feature (if that is what you are referring to here) the instructions are in the owners manual, have you looked? they are there.

Posted on Jan 19, 2010

egstriker23
  • 44 Answers

SOURCE: How to get at the

First, you will need to jack up the driver side front wheel.
Then, remove the wheel.
With the wheel off, you can remove the plastic fasteners holding the battery access panel (bottom front section of inner wheel well).
After you remove the cover you can reach in and disconnect the cables, then remove the battery.

Hope this helps!

Posted on Oct 27, 2010

  • 14585 Answers

SOURCE: 2000 dodge status non and I have brake pressure at

When you do a brake job with drums. You have to adjust the brakes by hand the first time. It doesn't hurt to put a little lude on the slack adjusters. Also if your reusing the brake drums, you need to grind or file the lip off the edge of the drum. this will throw off the adjustment.

Posted on Dec 05, 2010

  • 34 Answers

SOURCE: there is no air blowing out of my rear ac vents

Seen this problem Yesterday, we think it is a door blend actuator, but if it is only 5 months old take it back to the dealer and have them complete the warrenty.

Posted on Jan 09, 2011

  • 223 Answers

SOURCE: What is the order to

Start at the wheel farthest from the master cylinder and work your way to the closest for last. Typically RR, LR, RF, LF.

lp

Posted on Jan 11, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is camshaft sensor located on 2010 dodge journey?


here is a link that will show you a diagram for the 2010 Dodge Journey 4Cyl.

I hope this helps

http://engine-codes.com/qa/17736/location-of-crankshaft-sensor

Apr 26, 2015 | 2010 Dodge Journey

1 Answer

How do you replace the front brake pads on a 2010 Dodge journey?


remove the wheel after supporting the car,with a jack stand, then you remove the two bolts that holds the brake caliper then remove the old pads then you push back the caliper piston with a clamp or a big channel lock pliers replace the new pads and after you did the two front wheels start your car and before moving pump up the brakes properly

May 03, 2014 | 2009 Dodge Journey

1 Answer

I have a 2010 dodge journey and the shifter get stuck in park


If your parking on an incline, that would possibly cause it plus switch at brake pedal may need to be adjusted. If you find pushing harder on brake pedal helps, have it adjusted, or replaced.

Jan 18, 2014 | 2010 Dodge Grand Caravan

2 Answers

Installed new rorors and brake pads to front of my 2009 Journey. Now I have good brakes but the pedal will slowly go to the floor if your foot is left on the pedal as you would while at a stop light. Why...


Did you open a brake line during your repair? If so, you'll need to bleed the air out of your brakes. If that's not the problem, check your brake booster. Had that problem on my Honda and a new booster corrected the problem.

Sep 07, 2011 | 2009 Dodge Journey

2 Answers

What is the order to bleed brakes on a 2009 Dodge Journey


Start at the wheel farthest from the master cylinder and work your way to the closest for last. Typically RR, LR, RF, LF.

lp

Jan 11, 2011 | 2009 Dodge Journey

1 Answer

Replaced brake pads on 2009 Dodge Journey, but now when the brakes are pressed the caliper won't engage.


Well you need to check your fluid level on the master cylinder first. Then I suggest that you bleed the brake system. Always start bleeding from the wheel furthest away from the master.

Nov 22, 2010 | 2009 Dodge Journey

Not finding what you are looking for?
2010 Dodge Journey Logo

Related Topics:

105 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8201 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...