Question about 2002 Chevrolet Malibu

Open Question

Where is the purge valve solenoid on my 2002 malibu

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

gh20s
  • 343 Answers

SOURCE: Chevy 2002 Malibu ERG valve

Symptoms of a bad EGR valve are usually stumbling idle or the engine stalling when the car is warm (normal operating temperature). Find the EGR valve and locate the vacuum line attached to it. Start the engine cold and wait for it to warm up. When the engine starts to stumble, pull off the vacuum line. If the EGR is bad, the engine idle will stabilize and no longer stumble.

Posted on May 25, 2010

  • 5481 Answers

SOURCE: check engine light is on

Go to Autozone or Oreillys for a free scan. The scanner will tell you exactly what is wrong. Now sometimes a Code will show a problem in the Purge system and its just a loose gascap. But other times it can be a small leak in a vent hose.

The Autoparts people can help you find the problem and sell you some of the parts to correct it. After you add a new part you need to clear the onboard computer with a scanner or unhook the NEG cable for 10 minutes.

Posted on Sep 05, 2010

SOURCE: 2007 chevy tahoe 4.8 emissions purge/valve

In the rear up high near fuel tank or along frame rail,
among the EVAP System Components

Need a diagram of system to find & test components

Really need a scan tool & EVAP Smoke machine,
to test & find out, if you have anything that doesn't work

I assume you know codes do not tell you what is wrong
or what to replace,vehicles do not self diagnose themselves
and likely never will

Posted on Jun 14, 2011

wyet_helps
  • 339 Answers

SOURCE: I can't locate the canister

{: ) Top right center of the engine, near the fuel injector connector.



wyet_helps.gif

Posted on Jul 02, 2011

  • 7353 Answers

SOURCE: show vaccum lines for purge valve solenoid for egr

the purge valve doesn't have anything to do with the EGR so I don't know what you want? there should be a black plastic line with a green cap on it, follow that line to the purge valve near the intake manifold.

Posted on Aug 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Need to replace purge valve solenoid on my 2008 trailblazer 4.2 liter engine


Edward, Check the attached links,instruction and guides on how to change your purge valve. Good luck. "I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Purge valve solenoid repair on 2007 trailblazer
replacing purge valve control solenoid
2002 GMC Envoy evap purge solenoid

Jul 22, 2016 | 2008 Chevrolet Chevrolet TrailBlazer LT

1 Answer

2002 Nissan Frontier showing a P01444 code


P1444 EVAP Canister Purge Volume Control Solenoid Valve
This system controls flow rate of fuel vapor from the EVAP canister. The opening of the vapor by-pass passage in the EVAP canister purge volume control solenoid valve changes to control the flow rate. The EVAP canister purge volume control solenoid valve repeats ON/OFF operation according to the signal sent from the ECM. The opening of the valve varies for optimum engine control. The optimum value stored in the ECM is determined by considering various engine conditions. When the engine is operating, the flow rate of fuel vapor from the EVAP canister is regulated as the air flow changes.

Feb 11, 2014 | Nissan Frontier Cars & Trucks

1 Answer

Need to know where to find the canister purge valve


For the location of canister purge valve,check the following help links mentioned below:--
Click the link :---

Location for EVAP Purge Valve Solenoid?

http://schematicsdiagram.blogspot.in/2012/06/2002-nissandatsun-pathfinder-location.html


------------------

How to disconnect the hose form the Evap Canister?

http://schematicsdiagram.blogspot.com/2011/12/how-to-disconnect-hose-form-evap.html

-------------

2004 Chrysler PT Cruiser: Location of EVAP Purge Solenoid Valve?

http://schematicsdiagram.blogspot.in/2012/06/2004chrysler-pt-cruiser-location-of.html

-----------
These will help.
Thanks.

Jan 08, 2013 | Cars & Trucks

1 Answer

I have a code P0449 on my 1999 chevy malibu 3.1


check engine light ison,autozone says code is P0449 this is whattheir ticket says:

The PCM has determined that a malfunction exists in the electrical circuit for the vent valve/solenoid in the evaporative emission control system.

Definition:
EVAP (Evaporative Emission System) purge/vent solenoid circuit condition

Explanation:
The solenoids and system wiring are monitored for opens or shorts

Probable Causes
1- Purge or vent solenoids defective
2- Check connevtor and wiring
3- Fuel saturated vapor canister
4- Failed EVAP vent solenoid

Dec 06, 2012 | 1999 Chevrolet Malibu

1 Answer

2002 Kia sportage with the code p0443


Hi Brittany:
The Evaporative Emissions System (EVAP) allows fumes from the gas tank to enter the engine to be burned, rather than vented into the atmosphere as an emission. The purge valve solenoid is supplied switched battery voltage.

The ECM controls the valve by operating the ground circuit, opening the purge valve at specific times allowing these gasses to enter the engine. The ECM monitors the ground circuit as well, watching for faults. When the purge solenoid isn't activated, the ECM should see a high voltage on the ground circuit. When the solenoid is activated, the ECM should see the ground voltage pulled low, close to zero. If the ECM doesn't see these expected voltages, or senses an open in the circuit, this code is set.

Potential Symptoms: P0443 trouble code symptoms could be just an malfunction indicator lamp (MIL) illumination. There may be no drivability problems at all. But, it's also possible to have a lean condition or a rough running engine if the purge valve is stuck open. Usually though, these symptoms are accompanied by other EVAP codes. Another symptom may be excessive pressure in the gas tank in the form of a "whooshing" sound when the cap is removed, indicating a purge valve that isn't working at all or stuck closed.

To cause a P0443, there has to be a problem with the purge control CIRCUIT, not necessarily the valve. Usually they are a unit housing the valve and the solenoid as an assembly. Or it could be comprised of a separate solenoid with vacuum lines to a purge valve. That said, it could be any of the following:
Bad purge solenoid (internal short or open)
Wiring harness chafing or rubbing another component causing short or open on control circuit
Connector worn, broken or shorted due to water intrusion
Driver circuit inside powertrain control module (PCM) is bad

Possible Solutions
1. Using a scan tool, command the purge solenoid to activate. Listen or feel for a clicking coming from the purge solenoid. It should click once, or on some models it may click repeatedly.

2. If it doesn't click with scan tool activation, unplug the connector and examing the solenoid and connector for damage, water, etc. Then check for battery voltage on the feed wire with the key on. If you have battery voltage, then ground the control side manually using a jumper wire and see if the valve clicks. If it does, then you know the solenoid is working properly but there is a problem with the control circuit. If it doesn't click when you manually ground it, replace the purge solenoid.

3. To check for a problem on the control circuit (if the solenoid tests okay and you have voltage to the solenoid) plug the solenoid back in and remove the control circuit (ground) wire from the ECM connector (If you're unsure how to do this, do not attempt). With the ground wire removed from the ECM, turn the key on and then manually ground the Purge valve control wire. The solenoid should click. If it does, then you know there is no problem with the control wire to the solenoid and there is a problem with the ECM purge solenoid driver circuit in the ECM. You'll need a new ECM. However if it doesn't click, then there must be an open in the wiring between the ECM and and the solenoid. You must find it and repair it.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Feb 23, 2012 | Kia Sportage Cars & Trucks

1 Answer

Where is the evap purge canister valve located on a 2002 kia sedona?


The canister purge valve is located behind the intake manifold in the engine compartment on the firewall side .It should be a small round solenoid with a wire connector attached.It will have a feed hose from the evap cannister to the purge valve and then to the intake manifold.The evap canister is located on under the vehicle on the right side of the gas tank and is held in place by a bracket.If you follow these hoses it will also get you to the canister purge valve.I hope this helped.

Feb 03, 2011 | 2002 Kia Sedona

1 Answer

I got a Error Code P1441 Definition EVAP System Flow During Non-Purge Conditions Possible Causes: EVAP purge valve, purge pipe, or the charcoal canister has a temporary blockage (this fault could...


P1442 usually gas cap. P1449 usually vent solenoid. P1441 usually always a faulty FTP sensor. Very problematic to Malibu, Grand Am Cavaliers and Aleros. That would be my first area to check. They are also known for poor wiring connections at the Left rear passthru connector to the fuel tank and vent solenoid, but not necessarily for that code.

Jan 25, 2011 | 2001 Pontiac Grand Am SE

1 Answer

I need to locate EVAP cylinder control solenoid. Where is it in the 2002 model??



EVAP Canister Purge Connectors

37e823e.jpg

Fig. EVAP Purge valve solenoid (3) mounting bolt (2) and insulator (1) on 2000-2005 4.8L, 5.3L, 6.0L Engines

Hope this help (remember comment and rated this post).

May 05, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

Check engine light on


The computer never tells you what to replce jsut the symptoms and whats malfunctioning, what is happening is it can't pressureize the fuel tank and canister purge valve, so i could be as simple as a bad gasket on the fuel tank or a dirty canister check valve or a broken hose on the purge canister so check these things first.

Jun 21, 2009 | 2002 Chevrolet Malibu

2 Answers

Check engine light on po441


P0441 = Evap. Emission Ctrl. System Incorrect Purge Flow. Listed Cause - valve stuck in open position.
INSPECTION (4 cylinder engine)
When disconnecting the vacuum hose, make an identification mark on it so that it can be reconnected to its original position.cc59427.jpg 1. Disconnect the vacuum hose (black with red stripe) from the solenoid valve. 2. Detach the harness connector. 3. Connect a vacuum pump to the nipple to which the red-striped vacuum hose was connected. 4. Apply vacuum and check when voltage is applied to the EVAP Canister Purge Solenoid Valve and when the voltage is discontinued.
31f3588.jpg Battery voltage Normal condition
When applied Vacuum is released
When discontinued Vacuum is maintained

V6 Purge Solenoid Valve
bc8d2fa.jpg

Jun 04, 2009 | Hyundai Motor 2002 Sonata

Not finding what you are looking for?
2002 Chevrolet Malibu Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75117 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7772 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...