Question about Cars & Trucks

Open Question

1988 jeep wrangler fuse panel - Cars & Trucks

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 4 Answers

SOURCE: Jeep wrangler Fuse box

i had the same problem. i drive a 95 so im not sure if it differs from were the fuse box is. look righ above you pedals to your far left. it should be right there. also if you instruments went out it will be a 15 fuse. its a blue fuse. next my panel went out cuz of the wires on my transmission. if yor looking at your jeep at the front. the wires will be on your left. make sure they are not burned or anything. it will be right on the side of your tranny. mind got burned by the exaust so they were shorting. check that is and see if that is what is it. for a temp fix just put some electrical tap around the wires and you should be set for a wile. good luck

Posted on Jun 30, 2008

  • 6982 Answers

SOURCE: 1988 Wrangler Ignition Switch Removal

There are four (sometimes two) bolts that hold the steering column to the dash. remove them & column will come down to let you get in there.
follow instruction sheet with switch. if you don't get it centered correctly it wont work correctly.

Posted on Jan 05, 2009

  • 16 Answers

SOURCE: Jeep wrangler Fuse box

You have two locations for the fuse box. One is either under the hood or behind the glove box. I would pull apart the glove box and take a look.

Posted on Jan 10, 2009

lebones337
  • 152 Answers

SOURCE: VACUUM HOSE DIAGRAM FOR 1988 JEEP WRANGLER 4.2 I6?

here is a link with all the vacum diagrams for your jeep. hope it helps.
http://www.autozone.com/addVehicleId,1076002/initialAction,repairGuide/shopping/repairGuide.htm?pageId=0900c1528008ab9d

Posted on Feb 12, 2009

  • 3 Answers

SOURCE: i have a 1988 jeep wrangler that won't idle.

1. check for vaccuum leaks.
2. check for a check engine code
3. check the throttle body/butterfly plate for carbon build up.

Posted on Sep 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a heater resitor on jeep 1988 wrangler


Check switch at dash , might be burned , lost contact .

Jan 22, 2013 | 1988 Jeep Wrangler

1 Answer

Need the Vacuum Diagram for a 1988 Jeep Wrangler 4.2 liter


try chiltons I got the haynes and the diagram is too hard to follow

Jul 20, 2010 | 1988 Jeep Wrangler

1 Answer

I have a 1988 jeep wrangler that won't idle.


1. check for vaccuum leaks.
2. check for a check engine code
3. check the throttle body/butterfly plate for carbon build up.

Sep 09, 2009 | 1988 Jeep Wrangler

1 Answer

1988 Jeep Wrangler conversion kit


Check out a site called (partsmike.com) if anyone can help Mike can.

Mar 26, 2009 | 1988 Jeep Wrangler

1 Answer

1988 Wrangler Ignition Switch Removal


There are four (sometimes two) bolts that hold the steering column to the dash. remove them & column will come down to let you get in there.
follow instruction sheet with switch. if you don't get it centered correctly it wont work correctly.

Jan 04, 2009 | 1988 Jeep Wrangler

1 Answer

YJ Blinker Relay


Hi there,

Both the hazard and the blinker flashers are located on the fuse panel. They pull straight out.

When both turn signals fail, the cause may be a blown fuse, a faulty flasher, a broken turn signal switch or a bad connection.

When you try the turn signals, do they light up and not blink?
-If so, probably the flasher unit.

When you try the turn signals, does nothing happen?
-Check the fuse

Let me know if the problem continues after replacing the flasher.

Mike

Aug 30, 2008 | 1988 Jeep Wrangler

1 Answer

1988 jeep wrangler no fuel


check your fuel pump relay and your ignition switch those numbers you gave for voltage are not right, please recheck that you have a ground and 12volts at the pump while cranking please rate -jeff

Jul 09, 2008 | 1988 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...