Question about 1991 Mercury Capri

1 Answer

Remove front bumper

Got a damaged bumper need to remove don't know how got a partial manual but section for removal was restricted by Ford to reprint. Get answer on internet for every car but 91 Mercury Capri. I am not a mechnic but if I see a diagram i can figure how to take it off, thanks

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mercury Master
  • 43,969 Answers

You might find the information you need in the automotive section of your local library

Posted on May 10, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
johnny5846
  • 379 Answers

SOURCE: replacing timing belt 91 mercury capri

according to a manual , the crank key will point to arrow , the intake cam should have an letter i aligned with arrow on belt cover and exhaust cam should have letter e aligned with arrow on belt cover , and as always rotate the engine 2 full turns to inspect timing marks before cranking or trying to start the engine . if you haven't taken the original belt off yet , paint your marks for quicker reference .

Posted on Jan 02, 2009

richrobi
  • 15 Answers

SOURCE: 1991 4 clinder mercury capri build down under,

The firing order is 1-3-4-2
All things Capri are found at:
http://www.techcapri.com/

Hope this helps

Richard R
SE XR2 turbo

Posted on Jan 07, 2009

  • 2 Answers

SOURCE: 2000 mercury cougar front door panel removal

its very easy, takes maby 10min, there are hidden screws under the cougar symbols on the door, and under the black circles on the carpeted part of the door, they all just pop off, then there are a few on the ouside rim of the door 2 on each side i think, it might require a little jiggling but the car is pretty simple

Posted on Mar 16, 2009

chrischronic
  • 235 Answers

SOURCE: 2000 Mercury Sable 24V 3.o engine. Need to know

yes about the upper intake and the only way i know how to check the coils is with a engine anilyser or if the check engine light comes on then you can have the codes pulled and that will tell you which cylender is missfiring this engine has a indevidual coil for each spark plug so thares 6 of them and thay slide right down over the sparkplugs

Posted on May 05, 2009

  • 316 Answers

SOURCE: can't remove crankshaft timing belt pulley BOLT!

You will have to brace the crankshaft somehow, either by way of the flywheel, or the pulley. The trick to getting the bolt to break is "heat". Propane will sometimes work, but it's generally not hot enough. You want to get that bolt glowing if you can, and hit it with air impact then. Be careful not to burn yourself!

I hope this helps you, and I wish you luck on your repair.

Posted on May 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Where is the windsheild washer pump on a 2002chrysler Cirrus


It's attached to the windshield washer tank

Dec 31, 2017 | Cars & Trucks

1 Answer

How to drain coolant from 1999 ford taurus


There is a plug under the air dam under your car's front bumper.You remove the air dam and it is a whitish plug on the driver's side at bottom of the radiator. don-ohio (:^)

Nov 27, 2011 | 1999 Ford Taurus

1 Answer

I need to replace the driver's side headlight assembly and need to learn the steps necessary to remove the damaged headlight and insert the new one. From what I can tell, one or more of the front...


Hi,

To remove the headlamp assy. you need to gain access to the bolts that are hidden by the front bumper.. you need to pull back the inner fender well closest to the edge of the front bumper and there is a 10mm bolt going into the bumper you need to remove then you will be able to pull the edge of the bumper away from the fender you will need to remove any clips and or bolts around the grill area to give enough room to pull the bumper cover out of the way enough you need to get your hand and a wrench or socket into the lower part of the fender there is a bolt there that holds the headlamp assy. in remove that bolt as well as the other bolts on the top of the core support and then you will be able to move/wiggle headlamp out enough and disconnect the wiring and remove the assembly be careful not to scratch the fender or bumper cover.. you may want to put some masking tape on the fender and bumper cover so as not to scratch during removal.

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Aug 19, 2011 | 2006 Toyota Highlander

1 Answer

How to remove headlamp assembly 2006 Ford Five Hundred


bulb replacement?

You may be able to clear bumper cover by pusihing down while pulling out lamp.

Please rate.
---------------------------

SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005
Headlamp Assembly - Five Hundred, Montego adobe.gif Printable View (211 KB) n0050703.jpg
Item Part Number Description 1 W702706 Top headlamp assembly bolts (2 required) 2 W704551 Side headlamp assembly bolt 3 W702706 Front headlamp assembly bolt 4 13005/13006 Headlamp assembly (RH/LH)
Removal
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 4 bolts and the headlamp assembly.
    • Disconnect the electrical connectors.
Installation
  1. Connect the electrical connectors and position the headlamp assembly in place.
  1. Install the side headlamp assembly bolt.
    • Tighten to 11 Nm (8 lb-ft).
  1. Install the front headlamp assembly bolt.
  1. Install the top outboard headlamp assembly bolt.
  1. Install the top inboard headlamp assembly bolt.
  1. Install the front bumper cover. For additional information, refer to Section 501-19.

Aug 03, 2011 | Ford Five Hundred Cars & Trucks

1 Answer

The park assist system switches itself off after a minute. Problably a faulty sensor? But how to find out wich one is bad end how can they be removed out of the bumpers of my 2005 ML270cdi?


Yes it does sound like you have a faulty sensor, If you're in the NY area I'd have a look at it for you. If you're not then you'll need to find someone with the mercedes benz computer (SDS) to find out exactly which sensor is defective. Through the computer it's possible to test each sensor individually to see which one is not working. I'm not 100% sure on this, but I believe there's a very good chance you'll have to remove the bumper to get the sensors out and they are clipped into a housing in the back of the bumper. Hope this information helps.

Please don't forget to rate my answer. Thank You.

Jun 12, 2011 | 2005 Mercedes-Benz M-Class

1 Answer

How do I remove the radiator form my 1997 ford taurus do I have to remove the bumper?


No,

Section 03-03: Engine Cooling 1997 Taurus, Sable Workshop Manual
REMOVAL AND INSTALLATION Radiator Aluminum Core, Crossflow
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Fuel Line Disconnect Tool Set T90T-9550-S
Removal
svh~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not mix Standard (green) Coolant with Extended Life Coolant (orange). If mixing occurs, drain engine cooling system and refill with originally equipped coolant type. If this contamination occurs, the service interval of Extended Life Coolant will be reduced from 6 years/150,000 miles to 3 years/30,000 miles.
  1. Disconnect battery ground cable (14301).
  1. Remove battery (10653) as described in Section 14-01 .
  1. Remove clip retaining contant control relay module and position module aside.
  1. Remove battery tray (10732) as described in Section 14-01 .
  1. Remove radiator cap (8100).
  1. Raise vehicle on hoist as described in Section 00-02 .
  1. Remove radiator splash shield.
  1. Drain engine cooling system as described in this section.
  1. Remove the radiator mounting bracket assembly.
  1. Remove lower radiator hose (8286).
  1. Partially lower vehicle.
  1. Remove upper radiator hose (8260).
  1. Remove radiator overflow hose (8075).
  1. Remove upper A/C condenser core retaining bolts.
  1. Remove upper transmission oil cooler tube clips.
  1. Remove lower transmission oil cooler tube (7C410)(EPN=7C410)using 3/8 Inch Fuel Line Disconnect Tool T90T-9550-C.
  1. Raise vehicle on hoist.
  1. Remove lower transmission oil cooler tube clips.
  1. Remove lower transmission oil cooler tube (7C410)(EPN=7C410)using 3/8 Inch Fuel Line Disconnect Tool T90T-9550-C.
  1. Remove transmission oil cooler bracket and position transmission oil cooler aside.
  1. Remove lower A/C condenser core bolts and position A/C condenser core (19712)aside.
  1. Remove radiator support bracket.
  1. Remove radiator (8005).

Jan 13, 2011 | 1997 Ford Taurus

1 Answer

How you take off the front bumber


have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal
  1. Raise and support the vehicle.
  1. Remove the RH and LH front wheel (1007).
  1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).




  1. Remove the four front fender brace screws.




  1. Remove the two front fender brace nuts.
  1. Remove the two plastic screws.
  1. Remove the seven clip buttons located under the front bumper cover (17D957).




  1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
  1. Remove the four front bumper cover brace bolts.




  1. Remove the front bumper cover from the vehicle.




  1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).



  2. Remove the eight front bumper bolts.




  1. Remove the front bumper from the vehicle.

Mar 02, 2010 | 1995 Mercury Villager

2 Answers

Need to replace head lamps on Ford Escape 2001,


there are 4 bolts that hold lamp in. the first 2 are obious. the others are behind the front bumper..the bumper must be removed to expose them...here is a cpoy of the manual to change..good luck

Headlamp Assembly Removal and Installation
  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. NOTE: Pull headlamp assembly forward to access electrical connectors.
    Remove the headlamp assembly.
    1. Remove the three bolts.
    1. Loosen the nut.
    • Disconnect the electrical connectors.
    a0045726.gif
  1. To install, reverse the removal procedure.
    • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

Apr 22, 2009 | 2003 Ford Escape

1 Answer

2002 ford escape passanger side headlamp assembly removal?


Removal and Installation
  1. NOTE: Make sure that the headlamp switch and the ignition switch are in the OFF position.
    Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. NOTE: Pull headlamp assembly forward to access electrical connectors.
    Remove the headlamp assembly.
    1. Remove the three bolts.
    1. Loosen the nut.
    • Disconnect the electrical connectors.
    a0045726.gif
  1. To install, reverse the removal procedure.
    • If necessary, adjust the headlamps. For additional information, refer to Headlamp Adjustment in this section.

Mar 03, 2009 | 2005 Ford Escape

2 Answers

Need to replace headlight assembly on 2005 Ford Escape


ithere are 4 bolts that hold it in...the top 2 are obvious..the others are behind the bumper. the bumper must be removed to acces them...here are the manuals instructions..

n0037234.gif
Item Part Number Description 1 — Headlamp assembly bolts (3 required) 2 — Headlamp assembly nut 3 13008 Headlamp assembly 4 14290 Electrical connectors
Removal and Installation
NOTE: Make sure the headlamp switch and the ignition switch are in the OFF position.
  1. Remove the front bumper cover. For additional information, refer to Section 501-19.
  1. Remove the 3 headlamp assembly bolts.
    • To install, tighten to 5 Nm (44 lb-in).
  1. Remove the headlamp assembly nut and the headlamp assembly.
    • Disconnect the electrical connectors.
    • To install, tighten to 5 Nm (44 lb-in).
  1. To install, reverse the removal procedure.

Jan 01, 2009 | 2005 Ford Escape

Not finding what you are looking for?
1991 Mercury Capri Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

79847 Answers

fordexpert

Level 3 Expert

5685 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...