Question about Cars & Trucks

1 Answer

I need to know how many pounds to torgue the pressure plate and fly wheel of a 95 vw jetta

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Should be approx 65ft lbs on the crankshaft and approx 70 in lb on pressure plate. If you don't have a alignment tool a deep socket can work and USE A CROSS PATTERN

Posted on May 09, 2013

  • Hunter Johnson May 25, 2013

    I went and looked it up at my local advanced auto and the pressure plate to the cam shaft was torqued to 44lbs plus a quarter of a turn and the flywheel was torqued to 15lbs all in a star pattern

×

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 341 Answers

SOURCE: torque settings for pressure plate and fly wheel

the flywheel is 50 -60 ft.lbs....pressure plate is 15- 25 ft. lbs..

Posted on Nov 22, 2008

  • 1 Answer

SOURCE: How do you reset a low tire pressure warning on a 2008 Jetta?

Do not..DO Not disconnect the battery ever!
it wll cost you a trip to the vw shop to re set the computer.......

bin there done that $46.00

Posted on May 04, 2009

  • 1 Answer

SOURCE: How do you reset a low tire pressure warning on a 2008 Jetta?

Reset the tire pressure warning, same as you would any service issue. Insert key in ignition, hold wrench button and min button, then start engine.

Posted on Jun 08, 2009

  • 22 Answers

SOURCE: The hood latch on my 95 VW Jetta is broke. I

well if the cable snapped you will need to try to get the front grill to pop out with out breaking it and look up and in to get to the little latch for the hood release.

Posted on Sep 12, 2009

  • 3 Answers

SOURCE: 95 vw jetta over heating

i changed my head gasket and still over heats i need options. also it looses anti freeze and it goes to the exhaust.

Posted on Nov 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to get fly wheel off of 77 Ford F100, 351 mod, 400 block?


I had to do this on my 1988 F250, if I remember correctly:
Remove in this order:
Driveshaft, Starter, lower cover plate, transmission, torque converter.
Flywheel s/b bolted to converter.
When driveshaft is removed - plug gap in tranny output - between drive shaft and housing - to prevent fluid spillage.
When removing transmission - plug hole in converter to prevent spillage.
When handling converter hold it flywheel side down until - to avoid fluid loss.
I presume you have all the correct tools and a helper.
hope it goes well

Jan 25, 2015 | Ford Cars & Trucks

1 Answer

Pressure plate torque


I have seen this problem many times, people change clutches but don't machine the fly wheel. this causes a shudder or the other thing is a crack in the fly wheel or pressure plate, sorry but transmission out fly wheel off to be machined, new clutch and pressure plate

Dec 04, 2013 | Cars & Trucks

1 Answer

How to change the clutch , pressure plate , and throout bearing on a 95 ford ranger 4x4 4.0 v6


The 1st step is to loosen your bell housing bolts and drop your starter. The remove your drive shafts the front drive shaft will slide out from the front and then pull it back to the rear. Then you must take your shifter lose from the Trans not the diff. then drop your cross member. Do not take the transfer case lose from the trans. If you can help it. You will then remove the trans. And unbolt the pressure plate. And everything should come off, make sure when you reinstall the clutch plate that you make sure the side that said to fly wheel is against the fly wheel. Make sure you tighten the pressure plate and clutch plate up with you line up tool all the way in and don't be afraid to tighten down on it. Because it isn't easy getting the Trans back up in there. The reassemble in the same order.

Jun 08, 2011 | Ford Ranger Cars & Trucks

1 Answer

I have a 2.0 2001 vw passat and the clutch has started slipping and grinding going into third , will i need to replace the fly wheel or just the clutch?


generally replace clutch and pressure plate as a kit, if the flywheel it worn they can be machined, most engineering shop can return the flyweel machined the same day

Mar 24, 2011 | Volkswagen Passat Cars & Trucks

1 Answer

Golf gt tdi just fitted new duelmass flywheel and gearbox but now got a bad vibration through the car?


I'm just guessing... Are your fly wheel bolts new? VW recommends NEW fly wheel bolts. Sometimes when you secure the axles specifically the inner CV joints to the drive flanges, may some how bind inside the casing (cage) and cause the vibration.

Clutch disc installation:
Tighten bolts diagonally to ensure that pressure plate is seated squarely on the flywheel without distortion. If not seated and torqued evenly, chattering and engagement problems may result.

Mar 06, 2010 | 2000 Volkswagen Golf

1 Answer

Replace clutch on 95 sidekick


You want to know the procedure?

You will need tools and a jack and a really good strong friend.

Remove the drive shaft. Unbolt the trans from the engine and put it aside. Unbolt the pressure plate and remove. The clutch plate will fall on you. Remove the fly wheel for resurfacing.

Take everything to the auto parts place that has a machine shop.

Get the flywheel resurfaced. Purchase a new/rebuilt clutch plate and rebuilt pressure plate. Get a new throw out bearing. Also get a clutch plate alignment tool while you are there.

When you get all the stuff together, reassemble it.

Put the fly wheel back in ... becareful of the starter. Add the clutch plate and the pressure plate. Use the alignment tool. Bolt it all back to proper torque spece. You will have to ask at the auto parts place for the torque specs. Oh yea, you will need a torque wrench for this.

Put the trans back in. You should probably change the universal joints while you are at it, front and rear.


Or - you could have a shop do this for about $500.00 to $1,000.00 and save on the band aids.

Thanks for your question at FixYa.com

good luck on your project.

Jan 18, 2010 | 1995 Suzuki Sidekick

1 Answer

Where is the pilot bearing located in a 1997 VW Jetta 5 speed


it is in the centre of the flywheel where the front of the input shaft of the gearbox locates

Jul 12, 2009 | 1997 Volkswagen Jetta

1 Answer

1991 vw jetta manual shows fuse #3 controls


I would check the ground for the plate lights. You have to remove the steering wheel and dash trim to get to the cluster for removal. Let me know if you need to know how to remove the cluster.

Apr 30, 2009 | 1991 Volkswagen Jetta

1 Answer

Torque settings for pressure plate and fly wheel


the flywheel is 50 -60 ft.lbs....pressure plate is 15- 25 ft. lbs..

Nov 22, 2008 | 1995 Mazda B-Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...