Question about 2003 Buick Park Avenue

Open Question

Stability system service - 2003 Buick Park Avenue

Posted by on

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 131 Answers

SOURCE: servicing stability system

traction control/stability control is usually part of the abs(anti-lock brake system) system without a scanner it would be almost impossible to diagnose if your not firmiliar with abs and the way it works take it to a shop

Posted on Feb 24, 2010

  • 90 Answers

SOURCE: Service stability system message appears

i believe your vehicle has air ride suspension in addition to coil springs. i would check the lines that run from the air pump to the air bags. they will black lines that are located near each strut and will go to a pump that is located somewhere iether underneath the vehicle or inside a fender.

Posted on Mar 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gauge Info. display reads service stability system.


To start you have to run the codes from the stability control module, and once that's done then you can beging to look for the problem, only a tech II scanner can reset this module, also make sure all tires are the same size

Mar 17, 2015 | 2003 Buick Park Avenue

1 Answer

Stability system disabled light on no power


The stability system is software programmed into the ABS - antilock brake control module also the PCM - engine computer . service engine light DTC'S - diagnostic trouble codes stored . Your best bet , take it to a qualified repair shop or the dealer . You don't have the diagnostic equipment or knowledge to tackle this type of problem .

Jul 24, 2017 | 2003 GMC Yukon Denali

1 Answer

Service stability system code is on where do i start


Stability System actively monitors the movement of the vehicle and can adjust the movement of the vehicle in cases where it determines the car is not moving correctly, as in sliding on ice or snow.The system incorporates signals from the wheel speed sensors, yaw rate sensor, and steering wheel position sensor to determine any corrective action. Any failure of any of these components will result in a "Service Stability System" message.

Dec 31, 2011 | 2001 Oldsmobile Aurora

1 Answer

WHILE DRIVING DOWN THE ROAD THE ABS LIGHT CAME ON ALONG WITH THE TRACTION CONTROL LIGHT.WE BEGAN GETTING A SERVICE TRACTION CONTROL SYSTEM,FOLLOWED BY SERVICE STABILIZATION SYSTEM,FOLLOWED BY SERVICE ABS...


All are tied into the ABS system, traction as well as stabilization, This needs to be looked at by someone who can hook up a diagnostic tester to read the fault codes stored in the ABS system then perform the correct diagnostic procedures to isolate the problem

Jan 03, 2011 | Buick LaCrosse Cars & Trucks

2 Answers

THE SERVICE STABILITY SYSTEM LIGHT STAY ON, I HAVE 2002 CADILLAC TRUCK EXT


Whats dose it mean went I have my service stability system light on and it dosent trun off .. I have a Cadillac escalade truck 02 All wheel drive hope some one could help me.......

Oct 02, 2010 | 2002 Cadillac Escalade Ext

3 Answers

Servicing stability system


probably a reprogram at gm dealer.

Feb 24, 2010 | 2004 Buick Park Avenue

1 Answer

Service stablization system light intermittently


it is saying you have bad stuts. you need to have it scanned to see which ones are bad.

Dec 30, 2009 | 2000 Cadillac DeVille

1 Answer

The service stability light is on


It pertains to just what it says STABILITY. Your vehicle has a system that will sense if you are coming around a curve at about 90 MPH. It will automatically apply a light amount of braking to the proper wheels, thus hopefully eliminating you and your Uplander from flying off curve. With the light on as with any warning light , you must assume whether its real or not, that the STABILITY system IS NOT operating. Significant computer / sensor diagnosis will be necessary. Hope this helps

Apr 12, 2009 | 2008 Chevrolet Uplander

1 Answer

Service stability system


one of the four load stability sensors (one at each wheel suspention arm) has gone awry. Computer diagnostics (Advanced scan tool) will tell you which one. Suggest replace both on front or both on rear (whichever the case)

Jul 03, 2008 | 2002 Buick LeSabre

Not finding what you are looking for?
2003 Buick Park Avenue Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...