Question about 1990 Subaru Legacy

Open Question

Clutch slave cylinder location

Where is the clutch slave cylinder location

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is slave cylinder located on the motor


The slave cylinder, which is present only on manual transmission automobiles, is located at the transmission bell housing, where it provides the hydraulic pressure-to-mechanical pressure conversion that actuates the clutch fork to disengage the clutch plate from the pressure plate.

Oct 04, 2015 | 2003 Mitsubishi Lancer

1 Answer

Location of slave cylinder in holden combo van 02/03 model


That does not seem quite right. The slave cylinder "piston," while it extends to declutch with pedal compression, it would return under spring pressure for clutch application as pedal is released...essentially reversing fluid flow and recharging the foot cylinder. Slave cylinder leakage during clutching should "show" as sluggish/irregular clutching response noticable by irregular/difficult/clashing shifts..that and probable noticeable leakage from the bell housing in addition to too-high or too-low fluid level in the reserve bottle on the firewall. As for location of slave cylinder, the significant advantage of hydraulic over cable-&-release-bearing clutch actuation is that there is no use of leverage with hydraulic but, instead, centralized force applied to the clutch plate by a slave cylinder though the center of which runs the crank shaft on its way to the gear box. Please re-post with more complete details as to driveablity/shiftability factors and fluid checks, top-off frequencies, and the like. Essentially, the only way to fault isolate a slave cylinder is by elimination of all other faults and leak sources; or by tear down and inspection. If the latter, you should consider complete clutch rebuild and pilot bearing for all the trouble you will inccur, depending on existing clutch age and wear and tear factors (such as driver skill level). Sorry could not offer a more definitive answer at this point.

Nov 01, 2014 | Cars & Trucks

1 Answer

Is the slave cylinder inside the transmission


The clutch slave cylinder is at the throwout bearing. Inside the transmission makes no sense

Aug 14, 2014 | Pontiac Sunfire Cars & Trucks

1 Answer

Where is the slave cylinder for the clutch located. internal or externaly.


First thing to do is to see if you have a clutch slave cylinder or cable operated clutch. Second the slave cylinder is on the end of the lever that goes into the clutch housing Before you change the clutch make sure that the problem is not in the slave cylinder or clutch master cylinder or cable as the case may be.

Jun 09, 2013 | 1998 Dodge Avenger

1 Answer

I have a 2006 Kia Spectra5 hatchback......wondering if the master/slave cylinders are located inside the transmission or ouside? My mechanic can't tell me without looking at the car...?


So we are talking manual transmission clutch operation here?

Your master cylinder is located on the firewall, on the other side of the clutch pedal. Your slave cylinder is located next to the gearbox bell housing.

The slave cylinder:
11_6_2012_11_53_26_pm.jpg

The master cylinder:


11_6_2012_11_54_27_pm.jpg

Nov 06, 2012 | Cars & Trucks

2 Answers

Where is the 1999 Saturn SL2 slave cylinder located?


on a manual transmission the Clutch Slave Cylinder is located on the drivers side front of the transmission. You can locate it by first finding the clutch master cylinder on the drivers side of the firewall. Then fallow the plastic line to the front of the transmission.

To remove the slave you will first twist it then pull it out of the transmission.

The clutch slave and mater cylinder are replaced as an assembly.

Oct 07, 2011 | 1999 Saturn SL

1 Answer

Where is the clutch auto adjustment located at on a 98 manual Volkswagen jetta?


you most likely have a hydraulic clutch, which the clutch master cylinder is located on the firewall on the driverside close to your drivers side windsheild.it takes brake fluid to fill dot brake fluid will fill it properly. however if your slave cylinder on the transmission is leaking,this will require a replacement of the clutch slave cylinder. look for leakage under passenger side,,just under or below passenger side seat onto ground. recommend if you replace the clutch slave cylinder,you also replace clutch master cylinder located on the drivers side firewall at wind sheild.look under the car while someone pumps the clutch in and out,if you see brake fluid leaking under car onto ground or inside onto carpet at brake pedal,you have a bad clutch master cylinder. recommend you replace both slave cylinder and clutch master cylinder. this will save you lots of time and headaches. thank you for choosing fixya.com

Sep 24, 2011 | 1998 Volkswagen Jetta

2 Answers

Clutch suddenly has no resistance and car won't shift gears. Fluids were low, have put fluid in the reservoir but still doesn't work. How do you bleed a clutch line?


on the transmission there is a slave cylinder that works like a brake cylinder, when you apply pressure to the clutch pedal a rod inside the vehicle under the dash pushes into a clutch master cylinder, (almost like a brake master cylinder without the reservoir, as the clutch master cylinder works off the brake master cylinders reservoir) the plunger in the clutch master cylinder applies fluid pressure to the slave cylinder,(located down on the trans near the clutch fork assembly) which projects a piston rod into the clutch fork dis-engaging the clutch. To bleed the clutch slave cylinder locate the bleeder screw on the slave cylinder,break loose so it loosens and tightens easily. Check fluid in brake master cylinder reservoir,fill if needed, while bleeder on the slave cyl is closed have a helper push clutch pedal to floor and back 7-8 times, (At first the clutch might stay at the floor, just pull it up by hand or foot and continue) after several pumps with no rest time push pedal to the floor and hold down with foot pressure, at this time loosen the bleeder on slave untill fluid leaks out, watch for air bubbles, close bleeder and repeat untill there is no sign of air bubbles, (make sure to check fluid in the brake master cylinder and keep fill as needed, do not let fluid get less than 1/2 empty as it might **** air and you will have to start over) If this does not bring clutch to operate then you need to check if slave cylinder is reachig its full extension of push rod or not. If it is not then you will have to replace the clutch master cyl or the clutch slave cyl or both as seals are bad and wont hold pressure. Or you need to inspect the clutch fork,the throw-out bearing, or the pressure plate fingers and clutch plate for failure or broken bent parts. I hope it turns out to be a easy fix on that clutching thing.

Jan 14, 2011 | 1995 Nissan Pickup

1 Answer

How do you replace the slave cylinder


Step 1
Raise the vehicle and support with jack stand placed underneath the frame.
  • Step 2 Remove the cover from the reservoir on top of the clutch master cylinder. It will be located in the engine bay on the driver side of the firewall, near the brake master cylinder. Fill the reservoir with DOT 3 brake fluid. Do not allow the reservoir to run dry at any time during the bleeding process.
  • Step 3 Locate the clutch slave cylinder. It will be bolted to the clutch housing. Locate the small bleeder screw near where the hydraulic hose connects to the slave cylinder.
  • Step 4 Connect a length of clear plastic tube to the bleeder screw.
  • Step 5 Open the slave cylinder bleeder screw, by turning it counterclockwise. Have an assistant pump the clutch pedal until clean brake fluid seeps out of the bleeder screw. Then close the bleeder screw. Make sure the clutch master cylinder does not run dry.
  • Step 6 Have the assistant pump the clutch pedal a few times and hold it against the floor. While the pedal is held against the floor, open the bleeder screw and allow the some fluid to seep out. Close the bleeder screw before releasing the clutch pedal.
  • Step 7 Repeat the process listed in the step above and watch the fluid seeping out of the slave cylinder. The clutch is fully bled when there are no more air bubbles in the fluid seeping out of the slave cylinder. You will be able to see the bubbles in the clear plastic tubing. Do not allow the clutch master cylinder to run dry at any point.
  • Step 8 Lower the vehicle.
  • dont forgate to rate
  • Mar 02, 2010 | 1999 Isuzu Rodeo

    1 Answer

    Clutch problem,where is the slave cylinder located


    The clutch slave cylinder is located on the left side of the transmission, but i believe that the slave cylinder may come with the master cylinder and lines already attached

    Aug 20, 2008 | 1996 Dodge Ram 1500 Club Cab

    Not finding what you are looking for?
    1990 Subaru Legacy Logo

    Related Topics:

    25 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Subaru Experts

    yadayada
    yadayada

    Level 3 Expert

    76109 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8269 Answers

    Are you a Subaru Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...