Question about Cars & Trucks

Open Question

Why does my 454 chevy engine kick back sometimes when I try to start it

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

joecoolvette
  • 5660 Answers

SOURCE: 1998 454 engine wont start. starter replace selonoid replaced.

Items of interest.

1.When a starter fails to start a vehicle, and the wiring has been found to be bad, and changed, one suspects the wiring first.

2.If a starter is suspected to be bad, one takes it out, and performs a benchtest, or takes it to an auto parts store, and see if they can do a benchtest. They need to load test it, not just see if it will Spin!

This test result should stop the needless buying, of starter after starter. If you get three bad starters in a row from an auto parts store, I suggest it's time to change auto parts stores! (Make sure, you are not twisting the S terminal on the Solenoid, when installing the ignition wires)

3.The frame of your vehicle should be the Ground.

Make sure that the motor home manufacturer, hasn't reversed the system for this motor home, and is using the frame for Positive.
This was done in the past for some older vehicles, because it was thought to reduce rusting, of the frame. However, you're dealing with a motor home. Hard to say what type of system they used.
Normal, would be using the frame as a Ground.

In the normal type of setup, of using the frame as ground, make sure where the starter contacts that 454 Chevy engine block, that this area of the starter has no paint on it. The starter grounds through the engine block, and where the starter contacts the engine block.

Make sure also, that this area of the engine block has no paint on it.

Be sure that there are flat braided ground straps going from the frame, to the engine block. If they are an insulated wire, and not braided flat straps, be sure they are about the thickness of your little finger. You'll notice I stated -> They. There should be TWO of them. ONE, will NOT Do!

The frame is the ground. The starter gets it's Ground source from the engine. The engine gets it's ground source from the frame. The only contact the engine has to the frame, is the motor mounts, and the transmission mount. They have
RUBBER in the middle!
There HAS to be -> ground straps! There MUST be TWO of them for the correct amount of grounding!

4.Power to start the starter turning comes from the ignition switch. The reason you have a solenoid on the starter, is so that there won't be a wire that is the thickness of your little finger, going up to the ignition switch!

Check the wire that comes from the ignition switch, for power, once the ignition switch is turned to the Start position.

Battery -> Negative terminal disconnected. Ignition wire from starter disconnected. Put electrical tape on the terminal end, of the ignition wire you removed from the starter solenoid. (Goes to the -> S <- on the solenoid)

Leave the other wires on, put the nut back on, and tighten. (Use caution in this area. The nut is only 5/16 inch, or 11/32. This means that threaded post is TINY. DON'T overtighten! IF, the threaded post starts to turn, STOP! Pull out on the post.

Inside the solenoid cap, that you can't see, there is a square boss, on inside end, of this tiny threaded terminal post. The solenoid cap, has a square hole that this boss fits into. Keeps that tiny threaded post from turning. Inside the cap, the tiny threaded post is connected to a one strand copper wire. If you twist the tiny threaded post, more than 90 degrees, the wire will twist off! Time for another solenoid!

Wheels chocked. Transmission in neutral, and it's best to have the parking brake on, and someone in the drivers seat. Have this person hold their foot down on the brake pedal. This way you avoid any accidents happening to YOU, someone else, or property.

Reconnect the Negative battery terminal. (Order of connecting up a battery is ALWAYS, Positive terminal First, Negative terminal last)

Take a multimeter set it to DC, and to the 50 volt scale. Find a clean, non-painted surface on the frame, (Or scratch a little area), touch the Black lead, (Negative probe) of the multimeter to it. Touch the Red lead, (Positive probe), of the multimeter to the ignition wire, electrical tape partially removed. (Enough so you can make a good contact to that terminal. The tape is there, in case the wire slips out of your hand, and touches a ground. If it has no tape, you'll think it's the Fourth of July under there!)

No reading? Be sure the person inside, has the ignition switch in the starting position. Still no reading? Check that ignition switch out. See if it's getting power.

Posted on Apr 24, 2009

  • 93 Answers

SOURCE: Chevy 454 back fire

Ignition timing is set by the computer as long as the distributor pickup point is within reason.

It could be running too lean. One of the TBI injectors may be sticking or not working (wiring or computer problem), or fuel pressure could be low.

Posted on May 21, 2009

roniecon
  • 6826 Answers

SOURCE: i need the firing order diagram for a 1977 chevy 454 engine

1365472, 1 3 5 7 are on the pasengers side 2 4 6 8 are on the drivers side.

Posted on Sep 24, 2009

  • 1 Answer

SOURCE: rebuilt chevy 454 engine, now need distributor and

just put a new starter in my 1993 chevy 454 and now i'm not getting fire, the old starter solenoid was sticking and melted the neg battery cable. I'm wondering if that also burned something else out?

Posted on Apr 17, 2011

  • 42 Answers

SOURCE: show diagram for sparkplug wiring on 1996 chevy 3500 454 engine

1-8-4-3-6-5-7-2 GM motors are numbered on the driver side as 1-3-5-7 and on the passenger side as 2-4-6-8. These numbered cylinder go from the front of the motor toward the back. Hope this helps.

Posted on Mar 09, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT KIND OF TRANSMISSION IS IN MY RV? IT HAS A CHEVY 454 ENGINE.


454 chevy engine in motorhome - RV-Coach Online

www.rv-coach.com > Discussion Forum > Mechanic's Corner - Engines
Mar 25, 2010 - I have a 1995 winnebago elanden Chevy chasis and Chevy 454 motor.... I am trying to tighten or replace all the belt on my 1987 Fleetwood Southwind ... What type trans fluid,oil and filter does the 1984 chevy rockwood motorhome take? .... Havereplace ignition switch, check neutral safety switch at transmission, all OK. RV with Chevy 454 engine problems
Oct 18, 2015
454 P30 radiator removal
Jul 23, 2012
Overdrive Transmission Conversion
Nov 6, 2010
4L80E Transmission Problems
Nov 15, 2009
More results from www.rv-coach.com

Nov 24, 2015 | Cars & Trucks

1 Answer

Carburetor removal 454 chv engine how to 1982


Carefully mark a the vacuum hoses and take picture

Mar 27, 2014 | 2001 Daewoo Lanos

1 Answer

Show diagram for sparkplug wiring on 1996 chevy 3500 454 engine


1-8-4-3-6-5-7-2 GM motors are numbered on the driver side as 1-3-5-7 and on the passenger side as 2-4-6-8. These numbered cylinder go from the front of the motor toward the back. Hope this helps.

Mar 08, 2013 | Chevrolet 3500 Cars & Trucks

1 Answer

I have a 1995 Chevy 2500 6.5 turbo diesel and the blow. So I was wondering if theirs any gas engines that will bolt in its place? thanks D Hawkins


Any smallblock chevy to a bigblock chevy will bolt up. examples I would go with : 350 or a 454 . The 6.5 uses the same transmission bolt pattern as these engines. If it's an automatic the flywhell might still work on the 350 or 454.

Aug 04, 2010 | 1995 Chevrolet Silverado 2500

2 Answers

Car wont start


Probably a bad starter activator find it and tap on it sometimes it will kick the starter, but it means the starter will have to be replaced.

May 10, 2010 | 1999 Chevrolet Venture

1 Answer

Rebuilt chevy 454 engine, now need distributor and


just put a new starter in my 1993 chevy 454 and now i'm not getting fire, the old starter solenoid was sticking and melted the neg battery cable. I'm wondering if that also burned something else out?

Oct 27, 2009 | 1993 Chevrolet C/K 3500

2 Answers

I need the firing order diagram for a 1977 chevy 454 engine


1365472, 1 3 5 7 are on the pasengers side 2 4 6 8 are on the drivers side.

Sep 24, 2009 | 1977 Chevrolet Silverado 2500

2 Answers

Need transmission info for 1988 Chevy Silverado 454 C3500 dually


got a clutch pedal in there? If auto, it could be a 700r4 or some variation of that. You can likely get exact info from a dealer if you give them the vin #.

May 22, 2009 | 1988 Chevrolet C3500

1 Answer

1992 chevy suburban 7.4 454 THM 700 tranny problems!


Try and adjust the down shift cable..Sounds like either it is broke or out of adjustment..

Apr 05, 2009 | 1992 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

41 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...