Question about 2007 Hyundai Atos Prime

Open Question

Rear wiper fuse - 2007 Hyundai Atos Prime

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2013 Honda CRV rear wiper fuse problem.


I would bet that the 30 amp fuse feeds the motor and the 10 amp fuse feeds both of the switches. Can you remove the rear trim to gain access to the rear motor and unplug it?

May 31, 2018 | Honda Cars & Trucks

1 Answer

2005 buick rainier rear wiper fuse under rear seat has no power at the fuse box. Any solutions? Thanks, Fred


My info doesn't show a rear wiper fuse? It shows a circuit breaker for rear wipers? Can you clarify?
Now. it does show a rear washer fuse?

Dec 23, 2017 | Buick Cars & Trucks

1 Answer

Rear windshield wipers don't move in 2011 Chevy traverse when I try to turn them on. Is it the relay?


Check the rear wiper fuse in the instrument panel fuse box. The rear wiper switch sends a signal to the body control module for rear wiper operation. The BCM sends a satart signal to the rear wiper motor circuit board

Dec 05, 2017 | Cars & Trucks

1 Answer

Rear wiper notworking


Hey Joe , what make model an year vehicle ?

Apr 08, 2015 | Cars & Trucks

1 Answer

Rear wiper doesn't work


check rear wiper fuse and relay.if wiper motor getting power but do not work.rear wiper motor bad.if fuse and relay okay but no power going to rear wiper rear wiper switch could be bad.

May 14, 2013 | 2000 Seat Ibiza

2 Answers

Back windshield wiper won't turn on


The rear wiper has a dedicated fuse. It's the 10A R/WIPER fuse in the relay block. This supplies power to the rear wiper and washer switch and the rear wiper control unit. That unit also gets power from the 20A AUDIO (!) fuse in the engine room fuse box. If the fuses are OK, the ignition switch is in the ON position, and the rear wiper and washer switch is turned on the rear wiper should work. If not check all the components described to find where the loss of power is occurring

Nov 15, 2012 | 2005 Kia Sorento

2 Answers

Air bag light is on 96 grand caravan


i may be mistaken on if this applies to your model year but if the rear wiper does not work then check the fuse for rear wiper and replace if blown. make sure rear wiper switch is off and wiper is parked.if air bag light goes out after a few seconds then the rear wiper motor is bad causing fuse to blow. air bag module gets power for its fuse through wiper fuse.if wiper is not parked then fuse may blow when you turn yhe key on.you have two choices. replace wiper motor or remove tailgate door panel and unplug the motor

Apr 04, 2010 | 1996 Dodge Caravan

2 Answers

Rear wiper does not work at all. front wipers work fine. rear washer works


1. check the fuse to the rear wiper motor
2. check for power to rear wiper motor at the motor (power wire going in to the wiper motor with rear wiper switch on)
If you have good fuses & have power going in to the rear wiper motor...
3. Pull old rear wiper motor and install a new rear wiper motor.
Thank you please drive thru......

Feb 26, 2009 | 2001 Ford Expedition

1 Answer

99 Nissan Quest real wiper runs continually when ignition is on


Principles of Operation
Operation of the windshield wiper and washer is controlled by the front wiper/washer amplifier assembly. The front wiper/washer amplifier input comes from the multifunction switch by means of a voltage divider circuit. A constant voltage is applied to the multifunction switch by the front wiper/washer amplifier. When the multifunction switch is moved into the LO, HI, or intermittent position, the voltage is directed through a series of resistors. This results in various voltages being returned to the module for each switch position. The module then grounds the appropriate circuit, based on the voltage signal received back from the multifunction switch. This causes the wipers to run intermittently, or at the appropriate speed. Voltage is supplied to the wiper motor by the CJB fuse F46 (20A).
When the multifunction switch wash button is depressed, it bypasses all of the resistors returning a full voltage signal to the module. The module then grounds the appropriate circuits to operate the windshield washer pump for as long as the switch is depressed. The windshield wiper speed is dependent on the position of the windshield wiper/washer switch.
Voltage for the windshield washer pump is also provided by CJB fuse F46 (20A).
Operation of the rear wiper and washer is controlled by the rear wiper/washer switch.
Voltage is supplied to the rear window wiper motor by the fuse junction panel fuse F44 (10A).
The rear window wiper motor ground is made or broken by the rear wiper/washer switch. When the rear wiper/washer switch is moved into the WIPER position, it grounds the rear window wiper motor circuit, causing the rear window wiper motor to run once every 10-15 seconds.
Voltage to the rear washer pump motor is also supplied by the CJB fuse F44 (10A). The rear washer pump is directly controlled by the rear wiper/washer switch which makes or breaks the ground for the washer pump motor, depending upon its position.
If the vehicle is equipped with a movable liftgate glass, a liftgate glass switch is utilized to prevent rear window wiper operation when the liftgate glass is open. This same switch also causes the rear window wiper to drop down approximately three inches when the liftgate glass latch is released.
------------------------------------------------------------------------------------------
  • The wipers stay on continuously — rear wiper
  • Circuit.
  • Rear wiper/washer switch.
  • GO to Pinpoint Test L .


---------------------------------------------------------------------------------------------
Measure the resistance between rear wiper/washer switch C288 pin 6, component side and rear wiper/washer switch C288 pin 2, component side.
  • Is the resistance less than 5 ohms with the switch depressed, and greater than 10,000 ohms with it released?
sxv~us~en~file=arrow.gif~gen~ref.gifYes GO to L2 .
sxv~us~en~file=arrow.gif~gen~ref.gifNo INSTALL a new rear wiper/washer switch. TEST the system for normal operation.

Measure the resistance between rear wiper/washer switch C288 pin 6, circuit WB08 (BU/YE), harness side and ground.
  • Is the resistance greater than 10,000 ohms?
sxv~us~en~file=arrow.gif~gen~ref.gifYes INSTALL a new rear wiper /washer switch. TEST the system for normal operation.
sxv~us~en~file=arrow.gif~gen~ref.gifNo REPAIR circuit WB08 (BU/YE). TEST the system for normal operation.

65501dd.gif 7e9d21a.gif

Dec 08, 2008 | 1999 Nissan Quest

Not finding what you are looking for?
2007 Hyundai Atos Prime Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...