Question about 2003 Isuzu Rodeo

1 Answer

P0401 i have a 2003 rodeo and i need to n o how to clean the egr vale lines out

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Isuzu Master
  • 5,678 Answers

When you take off,look is open or close.

Posted on May 09, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

Cost to replace egr valve on a 2001 isuzu rodeo. The ECM has detected too much flow on the EGR system. How much will it cost to replace the ER valve on a 2001 Isuzu Rodeo


just went on line to rodeo egr valve and the price is around $345.00AUD. + labour to replace.Probably 75% that if in USA

Dec 25, 2014 | 2001 Isuzu Rodeo

1 Answer

1995 Toyota Tercel code p0409


if you manually push up on the EGR valve and the engine doesn't stall and the passages are all cleaned out then the problem is the EGR valve.

Aug 18, 2017 | 1995 Toyota Tercel

1 Answer

Where's the EGR valve located on my 2002 Izusu Rodeo


It's on the back off the motor in the middle passenger side.
Disconnect the wire, unscrew two bolts then you have egr valve in your hand its that easy. If you are putting new egr valve it's worth putting new gasket. BUT i'll recommend not to buy new egr valve, just clean it.
Thank you for using fixya and good luck
http://www.icess.ucsb.edu/~greg/rodeo/egr.htm

May 13, 2010 | 2002 Isuzu Rodeo

3 Answers

CODE P0401 COMEING UP


I had an OBD II 401 code and fixed it by cleaning out the EGR vacuum line in the intake manifold. I removed teh EGR Valve and the set screw below it. i used a rifle cleaning brush and one length of the rod. Then I replaced teh set screw. I started teh engind and let the vacuum **** some carb cleaner through the front port hole. when it was sucking good I replaced teh EGR valve and reset the codes. That fixed it.8_26_2012_9_39_13_pm.jpg

Feb 12, 2010 | 1999 Isuzu Rodeo

1 Answer

Sputter while driving and i have replaced the EGR valve . I have a new code of 1406.


Check the wiring harness for the valve. If all is well, then remove the valve and clean it, AND the lines. Some carbon probably got loose and contaminated your new EGR when you put it in.

Dec 26, 2009 | 1997 Isuzu Rodeo

1 Answer

Vehicle serges while idling


petrol or diesel ? if petrol maybe idle speed control vale needs a clean out .

diesel possible air ingress when did it last have a new fuel filter ? or egr valve may need cleaning out .

Dec 07, 2009 | 2004 Ford Expedition

3 Answers

Engine light on replaced egr vale 2 times still same problem


Could be plugged or leaky egr vacuum line or the circuit itself is faulty. You can test circuit with an ohmmeter

Nov 20, 2009 | 2004 Dodge Ram 1500

1 Answer

The EGR vale is new, it it is rough idoling or driving..i drive about 104 miles a day..it use about 1/4 tank gas per trip. (new plugs) they are fowled out .. i pulled the wires one ata time no change in...


SCAN IT TO SEE IF YOU HAVE MAP SENSOR WORKING.ALSO CHECK VACUUM LINES GOING TO MAP SENSOR MAKE SURE ITS NOT. BROKE OR CRACK.CHECK COILS RESISTANCE.BAD COILS CAUSE ROUGH IDLING.SCAN MAKE SURE COOLANT SENSOR ISNT OPEN.REMOVE EGR VALVE. CLEAN OUT CARBON IN THE INTAKE PORT.USING A PIECE OF CLOTHES RACK.CLEAN UP DEBRIS.ALSO CHECK FUEL PRESSURE REGULATOR.CHECK VACUUM LINE TO FUEL PRESSURE MAKE SURE ITS NOT FULL OF GAS.AND DONT HAVE CRACKS IN IT OR BROKE.

Jun 06, 2009 | 1994 GMC Sierra

1 Answer

Holden 94 rodeo petrol


Good Day
Vale clearance cold
intake .006 in (.15 mm)
exhaust .010 in (.25 mm)

Timing
1. With transmission in Neutral or park, start engine and warm to normal operating temp. turn eng,and all accessories off. connect Tachometer. Connect timing light to no 1 spark plug wire.

2. Disconnect and plug fuel vapor canister purge hose and EGR vacuum hose. Start and ensure idle is 900 RPM. adjust idle as required. Check ignition timing ( 12 @ 900)

3. If adjustment is required, loosen distributor hold down bolt and turn until timing is within specification. Tighten distributor hold down bolt and recheck timing. adjust idle speed as required.

hope this helps

Cheers

Aug 18, 2008 | 1994 Isuzu Rodeo

Not finding what you are looking for?
2003 Isuzu Rodeo Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14378 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...