Question about Ford Explorer

Open Question

1998 ford explorer rear bumper diagram - Explorer Ford Cars & Trucks

Posted by Anonymous on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 92 Answers

SOURCE: 1998 Ford Explorer sport 4.0L 4x2 PCV Valve Location

the pcv is located on the rear(firewall) of the drivers side valve cover.turn counterclockwise and pull to remove be careful there are 2 small tabs inside the pcv hole in the valve cover(can feel with small finger) this is to hold valve in place so it wont leak.if you have a oil leak at the pcv a quick fix is to put a small amount of silicone around the pcv o-ring and install.wait hours for silicone to set up.

Posted on Oct 21, 2008

  • 1 Answer

SOURCE: 01 ford explorer sport trac rear timing chain diagram

They will not loan you the else will they continue to rip off the average garage junkie and make lots of money?

Posted on Nov 18, 2009

  • 271 Answers

SOURCE: 1998 ford explorer timing chain

7b612ce.tifIf you have any questions PSE come back . Good luck

Posted on Nov 30, 2009

  • 5763 Answers

SOURCE: need a vacuum diagram 1998 ford explorer v8 2wd

heres a vacuum diagram for a 1998 ford explorer with the v-8 engine, hope this helps,0bf912a.gif

Posted on May 11, 2010

  • 17970 Answers

SOURCE: I need a vacuum diagram

Check this...


Fig.: Vacuum hose routing for 1995-99 Explorer/Mountaineer models with the 4.0L engine (click for zoom)

I hope helps, remember to rate and comment this answer.

Posted on Oct 06, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Will a f150 alternator fit into a ford explorer?

i was wondering if a front bumper on a 1999 ford explorer would fit on a 2004 f150 the old body style any help or advice would br great thank you

Jul 09, 2012 | 1998 Ford Explorer

1 Answer

Where do I store the spare tire on a 1998 Ford Explorer? In the cargo area or does it go underneath? Thanks.

The spare tire is stored under the vehicle. There's a hole just above the license plate you insert the extended end of the jack handle into to lower and raise the spare tire. The jack and handle are stowed in the drivers side rear (just inside the rear hatch).
You can go to this FREE Ford website to view or download the users manual for this vehicle for a diagram if needed.

Nov 20, 2010 | 1998 Ford Explorer

1 Answer

Need a vacuum diagram 1998 ford explorer v8 2wd please

heres a vacuum diagram for a 1998 ford explorer with the v-8 engine, hope this helps,0bf912a.gif

May 11, 2010 | 1998 Ford Explorer

1 Answer

How do you replace the rear liscense plate lights

Look behind you bumper where the lights are installed. There should be a clip slipped over the back of the housing that holds the light into the bumper. 1 per light. Use some needlenose plyers or a screwdriver to push it off. The light sould pull out of the bumper from the other side. You can disconnect the harness is you wish or just replace the bulb. Whichever suits your fancy. After replacement put the holder back into the bumper and slip the clip back on behind it. 10 minute job.

Apr 06, 2010 | 1998 Ford Explorer

1 Answer

How do you give the spare tire from under the truck.

look thru the rear bumper theres a hole were u stik the wrench suppied

Mar 15, 2010 | 1998 Ford Explorer

1 Answer

How do you get the bulb out of the holder. Rear license plate

  1. Unfasten the lens retaining screws and remove the lens.
  2. Twist the socket/bulb assembly approximately 1 / 4 turn counterclockwise, then remove it from the lens.
  3. Withdraw the bulb from the socket.
  4. Installation is the reverse of removal.

  5. it also helps to open the trunk first to easier see what you are doing.

Nov 22, 2009 | 1995 Ford Explorer

1 Answer

Need to replace license plate lights on 95 ford explorer. can't reach underneath the bumper. does the plastic assembly just twist off?

  1. From underneath the rear of the vehicle, grasp the lamp socket and rotate it 1/4 turn.
  2. Pull the lamp socket from the lens.
  3. Pull the bulb from the socket
  4. Installation is the reverse of the removal procedure.

Exploded view of the rear license plate light assembly-step bumper shown, other styles are similar

Oct 20, 2009 | 1995 Ford Explorer

1 Answer

How to replace the front bumper and grill on a 97 ford explorer

you need a repair manual, Haynes or Chilton, there are too many places to explain here in this format, if you can not find these book at your local parts store, then try your local library, then sometimes even have the dealer shop manuals for your use, hope this helps

May 20, 2009 | 1997 Ford Explorer AWD

1 Answer

Need a rear light wiring diagram to wire up a 4point tow wire adapter on 98 dodge dakota
The complete bumper to bumper wiring diagram. Costs about $12 and it's well worth it.

Mar 29, 2009 | 1998 Dodge Dakota

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers


Level 3 Expert

5522 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides