Question about Cars & Trucks
You change it the same way as on the front. Replace the complete blade assembly
Posted on May 09, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Posted on Aug 24, 2008
you can unbolt the wiper arm and change to where you think it should be then bolt it back up /Please rate my response thank you very mudh
Posted on Jan 31, 2009
SOURCE: Changing Windshield Wiper Blades
if a picture is worth a 1000 words then this video is worth a bunch more... wait thru the ad at the beginning and you'll see it done ...
Should do it for you! http://www.expertvillage.com/video/9223_wiper-blades-remove.htm
Posted on May 25, 2009
Yes you can adjust them yourself. First you need to check that the wiper arms are not bent. If not, remove the cap at the wiper arm base, under it u will find a nut, remove this nut. you should now be able to remove the wiper arm. (it is comon for caravan wiper arms to be corroded on. If the arm dosen't come off, you may need to heat up the wiper arm with a propane torch. be careful not to melt the plastic cowel under the arm. OR you can use a wiper puller or a battery puller. do not force it, you can break the arm, DO NOT PRY AGAINST THE COWEL OR WINDSHIELD.
Once both arms are off, turn your van on and turn the wipers on. watch the wiper posts, turn the wipers off and watch the wiper posts return and stop in the "parked" position. Turn the van off. Install the passanger wiper arm first, it is positioned closest to the bottom an inch or two above the black cowel. It should be parrallel to the cowel. next install the drivers side wiper arm. it is positioned about 4 inches above the passanger wiper. again running parrallel to the cowel and passanger wiper. tighten the lock nuts down (do not over tighten) wet down your windshield with glass cleaner or windshield washer fluid and test wipers. If they still hit you can lower the passanger one a little or raise the drivers one a little (careful you don't raise the drivers one too much or it will 'jump' off the windshield at the top of the wipe).
good luck, hope this helps.
Posted on Nov 23, 2009
Testimonial: "Thank you so much for the help!! My brother read your reply and fixed the wipers in no time. I am very appreciative of your help! Maryg :)"
the pivot pin must be rusted to the point it does not want to move, try lubing it with wd40 or equivalent lube,at the bottom of the wiper arm just before the bolt that holds it to the car is the pivot point.that's where it has to be lubed.
Posted on Jan 18, 2010
Testimonial: " Thank you for the information. Will give it a try."
Tips for a great answer:
Jan 27, 2016 | Plymouth Cars & Trucks
Dec 18, 2015 | 2007 Chrysler Sebring Sedan
May 25, 2015 | 2008 Chrysler Town & Country
Jun 26, 2011 | 2003 Chrysler Town & Country
Nov 06, 2010 | Chrysler Town & Country Cars & Trucks
May 25, 2010 | 2009 Chrysler Town and Country
Jan 08, 2010 | 2003 Chrysler Town & Country
Dec 30, 2009 | 2001 Chrysler Town & Country
Jul 24, 2009 | 2001 Chrysler Town & Country
40 people viewed this question
Usually answered in minutes!