Question about Cars & Trucks

1 Answer

Chevrolet blazer door handle

Handle assembly fell off inside passinger door while it is closed and locked. What do I do?

Posted by on

  • D'Nise Stoddard-Maxey May 09, 2013

    Everyone is giving me directions as if the door was open, IT IS CLOSED AND LOCKED! Now can anyone answer with a real working solution?

  • D'Nise Stoddard-Maxey May 09, 2013

    The lock on mthe outside is not working either.

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Cars & Trucks Master
  • 21,873 Answers

You can't unlock it with the key from the outside ?

Posted on May 08, 2013

  • 1 more comment 
  • D'Nise Stoddard-Maxey May 09, 2013

    The locking mechanism seems to be broke or has fallen off with the rest of the unit.

  • D'Nise Stoddard-Maxey May 09, 2013

    As I just said, NO I CAN"T.

  •  Stephen
    Stephen May 09, 2013

    Please notice you only have one solution - the others are suggested by the website and may have nothing to do with your question. If you can not open the door from the outside, you'll have to remove the door panel and attempt to force the latch from inside the door.

×

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1861 Answers

SOURCE: Replace side door handle assembly

Remove the snap ring from under the inside door handle and plate (a rag around the base of the handle and a left-right tug on the rag may loosen it, or look under it & pry the snap ring off with a small hook tool

Remove the door lock knob bezel; remove the screw & slide it rearward

Remove the door trim; Remove the two clips; slide a thin, flat wide tool under the panel and pry towards you, there are 8 clips to dislodge

Pull the door trim straight up once all of the clips are loosened.

Easy.

Posted on Sep 25, 2008

txkjun
  • 409 Answers

SOURCE: Driver's door won't lock remotely after driving.

Your Beetle might be German in name only, those things are built in Mexico.

Posted on Feb 15, 2009

  • 508 Answers

SOURCE: inside door handle rod on a Jeep Wrangler 1999

You will need to remove the door panel. Most use a special clip to attach it to the lock mechanisim. Look in the bottom of the door to find the clip that fell off. If you can't find it you will have to go to chrysler to get another clip or try a wrecking yard and they will probably just give it to you.

Posted on Feb 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Back near side door lock latch won't fully open preventing me from opening door from inside or outside on 2005 Ford focus possible causes


The most common cause for this is the door opening lever on the lock assembly is sitting slightly between the open and closed position and will not allow the lock arm to operate properly. I am not positive, but I think the lever is cable operated by the inside handle. You may be able to remove the inside handle assembly and access this cable and slide it in and out to see if the door lock will open

Jan 27, 2016 | Ford Cars & Trucks

1 Answer

What part do I need? It opens from the inside. The handle is not snapped.


Are you saying the inside door handle isnt snapped,but the door wont open by pulling on the inside door handle or is it the outside door handle thats not working??Both the inside and outside door handle has a spring and other components on the backside of the handle which cant really be seen unless you remove the whole door handle assembly.One of these components are most likely broken or the rod that attaches between each handle and the locking mechanism(part that locks into the door striker to keep the door closed and releases it too)might have come loose from the back of the handle.The outside handle is usually mounted to the door by pop rivets or bolts/nuts.The inside handle is usually mounted with screws,but it really depends on what kind of car youre driving.Youll probably have to remove the handle to inspect it for damage.Open the door and watch the locking mechanism for movement while youre pulling on the door handle.If it doesnt move when you pull on the handle,the handle is definitely broke or the rod has come loose from the back of the handle.

Mar 09, 2015 | Cars & Trucks

1 Answer

2001 blazer driver door will not close. what do I do?


Probably stuck linkage on either the inside or outside door handle. Try spraying the latch mechanism on the end of the of the door with some WD40 and see if it will operate properly. If not, you'll probably have to pull of the door's inside panel and inspect/lubricate the linkage to both the outside and inside door handles.

Sep 29, 2013 | 2001 Chevrolet Blazer

1 Answer

The left rear door window fell off the track. How do I remove the door panel to access it.


This is the complete procedure you stop when you see the problem.



1. REMOVE REAR DOOR INSIDE HANDLE BEZEL


(a) Remove the screw.


(b) Using a screwdriver with its tip taped, disengage the 2 claws A.


(c) Pull out the the rear door inside handle bezel in the direction indicated by the arrow, disengage the claw B, and remove the rear door inside handle bezel.


2. REMOVE DOOR PULL HANDLE


(a) Using a screwdriver wrapped with the protective tape, disengage the 2 clips and remove the door pull handle.


3. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY


(a) Remove the screw.


(b) Disengage the 7 clips.


(c) Disconnect the connector and pull up on the rear door trim board sub-assembly to remove it.


4. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY


(a) Remove the bolt.


(b) Disengage the 2 claws and separate the rear door inside handle sub-assembly.


(c) Disconnect the 2 cables and remove the rear door inside handle sub-assembly.


5. REMOVE REAR SPEAKER


6. REMOVE REAR DOOR SERVICE HOLE COVER


(a) Disconnect each connector and remove the rear door service hole cover.


HINT:


Remove the remaining tape on the door side.


7. REMOVE REAR DOOR GLASS RUN


(a) Connect the window regulator switch assembly.


(b) Fully lower the door glass.


(c) Remove the rear door glass run.


8. REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY


(a) Remove the 2 bolts, the screw and rear door window division bar sub-assembly.


9. REMOVE REAR DOOR QUARTER WINDOW GLASS


(a) Pull out the direction indicated by the arrow, remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit.


10. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP


11. REMOVE REAR DOOR GLASS SUB-ASSEMBLY


(a) Remove the rear door glass sub-assembly as shown in the illustration.


(b) Disconnect the window regulator switch assembly.


12. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY


(a) Disconnect the connector.


(b) Loosen the temporary bolt.


NOTICE:


If the temporary bolt is removed, the rear door window regulator may fall and become deformed.


(c) Remove the 3 bolts and the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.


(d) Remove the temporary bolt from the regulator.


13. REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY REAR


(a) Using a "torx" driver (T25), remove the 3 screws and power window regulator motor assembly rear.


14. REMOVE REAR DOOR LOCK ASSEMBLY


(a) Disconnect the connector.


(b) Remove the bolt.


(c) Using a "torx" socket wrench (T30), remove the 3 screws.


(d) Slide the rear door lock assembly downward, pull out the link from the outside handle frame, and remove the rear door lock assembly and cables as a unit.


(e) Remove the door wire harness packing.


(a) Using a "torx" socket wrench (T30), loosen the screw.


(b) Disengage the 2 claws and remove the rear door outside handle cover.


(a) Disengage the 2 claws and remove the rear door outside handle pad rear.

Jan 03, 2011 | 2006 Toyota Highlander

3 Answers

How to replace exterior door handle on 2007 Versa.


You need a Torx head screwdriver T25. Open the door and on the side of the door is a small black grommet, remove grommet, inside is the torx screw you need to loosen for the lock mechanism to move. you dont need to remove the screw just loosen enough to move the lock assembly around. Once loose enough, install the door handle and tighten lock assembly back and put grommet back.
Here is a picture if you need a bit of visual clues.
http://img266.imageshack.us/img266/1218/versadoorhandlefix.jpg
_69.jpg

Nov 04, 2010 | 2007 Nissan Versa 1.8 Sl Hatchback

1 Answer

Drivers side mirror fell off the whole assembly how do i fix it


On a 1997 blazer, how to remove drivers side mirror
under your handle to close the door is two 7mm bolt and behind your handle to open the door is a philips screw and that plate behind it comes off then CAREFULLY remove the door panel trust me you dont want to break the plastic then you will see your mirror bolts and electrical wiring

Oct 21, 2009 | 1998 Chevrolet Blazer

1 Answer

I can't figure out how to remove the OEM door lock cylinder in my 1994 K1500 Blazer. I can get the handle unfastened, but not removed from the door. Also, can't figure out how to remove the retaining clips...


in order to remove the cylinder, You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge.then you have to pull back the seal covering the door and remove the bolts holding the handle, door cylinder, and linkage assembly from inside the door

Aug 18, 2009 | 1994 Chevrolet S-10 Blazer

2 Answers

Door lock assembly fell inside door


The same thing happened to my 2006 Aveo. Once you do the above find the lock and the screw that holds it in (they will both be in the bottom of the door). Put the lock back in place, put blue Loctite on the screw and screw it back in place and this problem will not repeat itself.

Aug 11, 2009 | 2005 Chevrolet Aveo

1 Answer

Car in minor frontal repair. Removed door handle LF Door, refitted, now door won't open


it sounds like the door lock mechanism that the door button rod connects to inside the door is in the locked position.
Has the rod for the door handle been connected to the lock mechanism?

May 12, 2009 | 2004 Volkswagen Golf

1 Answer

Front driver door wont close on 97 blazer


Make sure the latch hasn't already dropped into the locked positon. If it has pull on the door handle and raise up the latch.

Mar 18, 2009 | 1997 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...