Question about Cars & Trucks

Open Question

Diagnostic code 01 ignition circuit ZKO/airbag driver stage 1

Posted by Anonymous on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

mcalkins3
  • 123 Answers

SOURCE: diagnostic code p0135

What engine is in this vehicle? I assume the avalon would be a 3.0L or similar V6 engine. Bank 1 sensor one indicates one of the primary O 2 sensor controlling a/f ratio. Sensor one bank one would be the sensor located in the Front manifold, closest to the engine. Hope this solves your issue. I would first check the conector at this sensor for corrison before buying a new sensor.

Posted on Sep 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I fix error code B0010 in a 2014 6L Chevrolet Silverado 3500 HD?


Passenger Frontal airbag Stage 1 Deployment Control (Subfault) You have a fault in the passenger side airbag or its control circuit, what that is needs diagnostic work.

Sep 23, 2016 | 2014 Chevrolet Silverado 3500HD

1 Answer

How to fix code B0044


1. This code refers to a problem with the steering wheel stage 2 air bag circuit.

2. Disconnect the dual stage air bag connector at the lower steering column.

3. Substitute 2 ohm resistors across the stage 1 and the stage 2 circuits to the Sensing Diagnostic Module (SDM).

4. Recheck for codes. If no codes are set, reconnect the connector, remove the air bag and install the 2 ohm resistors across the stage 1 and stage 2 circuits.

5. If B0044 resets, replace the clockspring.

Feb 14, 2015 | 2003 Chevrolet Trailblazer Ext

1 Answer

WHAT IS THE 1994 FORD ESCORT AIRBAG CODE 34 REPAIR


Ford Airbag Fault Codes
Flash Code Component/Fault Description
- No Air Bag Indicator - Inoperative Indicator Circuit
- Continuous Air Bag Indicator - Diagnostic Trouble Code Timed Out, Diagnostic Monitor
Disconnected or Inoperative, or No Ignition Voltage to Diagnostic Monitor
12 Lost Battery Feed
13 Air Bag Circuit Shorted to Ground
14 Primary Crash Sensor Circuit Shorted to Ground
21 Diagnostic Monitor Not Mounted to Vehicle Properly
22 Safing Sensor Output Circuit Shorted to Battery Voltage
23 Memory Clear Circuit Improperly Grounded
24 System Disarm Failure or Internal Diagnostic Monitor Fault
32 Driver Side Air Bag Circuit High Resistance or Open
33 Passenger Side Air Bag Circuit High Resistance or Open
34 Driver Side Air Bag Circuit Low Resistance or Shorted
35 Passenger Side Air Bag Circuit Low Resistance or Shorted
41 Right Radiator Primary Crash Sensor Feed/Return Circuit Open
42 Left Radiator Primary Crash Sensor Feed/Return Circuit Open
44 Right Radiator Crash Sensor Not Mounted to Vehicle Properly
45 Left Radiator Crash Sensor Not Mounted to Vehicle Properly
51 Airbag diagnostic Monitor Internal thermal fuse Blown
52 Back-up Power supply Voltage Boost Fault
53 Front Crash Sensor High Resistance or Diagnostic Monitor Failure

Aug 12, 2014 | 1994 Ford Escort

1 Answer

Ford airbag code 54


94+ AIR BAG DIAGNOSTIC TROUBLE CODES/CLEARING
Code Component/Fault Description

No Air Bag Indicator - Inoperative Indicator Circuit
Continuous Air Bag Indicator - Diagnostic Trouble Code Timed Out, Diagnostic Monitor Disconnected or Inoperative, or No Ignition Voltage to Diagnostic Monitor.
12 Lost Battery Feed
13 Air Bag Circuit Shorted to Ground
14 Primary Crash Sensor Circuit Shorted to Ground
21 Diagnostic Monitor Not Mounted to Vehicle Properly
22 Safing Sensor Output Circuit Shorted to Battery Voltage
23 Memory Clear Circuit Improperly Grounded
24 System Disarm Failure or Internal Diagnostic Monitor Fault
32 Driver Side Air Bag Circuit High Resistance or Open
33 Passenger Side Air Bag Circuit High Resistance or Open
34 Driver Side Air Bag Circuit Low Resistance or Shorted
35 Passenger Side Air Bag Circuit Low Resistance or Shorted
41 RH Radiator Primary Crash Sensor Feed/Return Circuit Open
42 LH Radiator Primary Crash Sensor Feed/Return Circuit Open
44 RH Radiator Primary Crash Sensor Not Mounted to Vehicle Properly
45 LH Radiator Primary Crash Sensor Not Mounted to Vehicle Properly
52 Intermittent or Repaired Lost Battery Feed
53 Intermittent or Repaired Air Bag Circuit Shorted to Ground
54 Intermittent or Repaired Primary Crash Sensor Circuit Shorted to Ground
61 Intermittent or Repaired Diagnostic Monitor Not Mounted to Vehicle Properly
62 Intermittent or Repaired Safing Sensor Output Circuit Shorted to Battery Voltage
63 Intermittent or Repaired Memory Clear Circuit Improperly Grounded
64 Intermittent or Repaired System Disarm Failure or Internal Diagnostic Monitor Fault
72 Intermittent or Repaired Driver Side Air Bag Circuit High Resistance or Open
73 Intermittent or Repaired Passenger Side Air Bag Circuit High Resistance or Open
74 Intermittent or Repaired Driver Side Air Bag Circuit Low Resistance or Shorted
75 Intermittent or Repaired Passenger Side Air Bag Circuit Low Resistance or Shorted
81 Intermittent or Repaired RH Radiator Primary Crash Sensor Feed/Return Circuit Open
82 Intermittent or Repaired LH Radiator Primary Crash Sensor Feed/Return Circuit Open
84 Intermittent or Repaired RH Radiator Primary Crash Sensor Not Mounted to Vehicle
85 Intermittent or Repaired LH Radiator Primary Crash Sensor Not Mounted to Vehicle
Rapid Continuous Flashing of Air Bag Indicator (No Diagnostic Trouble Code) Both Primary Crash Sensors Disconnected Assembly Plant Mode

TROUBLE CODE CLEARING

1. Follow the diagnostic procedures to service the fault condition flashing on the air bag indicator prior to code clearing.

2. Cycle the ignition switch to OFF and then to RUN.

3. Observe air bag indicator prove-out (six ? two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.

4. Locate the Diagnostic "Trouble Code Clear" Connector (grey connector). located underneath the glove compartment, left side (06010) containing Circuits 631 (T/R) and 57 (BK).

5. Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground. This short must be made after the diagnostic trouble code flashes completely one time, but before the warning light stays on continuously.

6. Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).

7. Release short on Circuit 631 (T/R) to Circuit 57 (BK). This short must be released within 25 seconds after the diagnostic monitor tone sounds.

Diagnostic trouble code is now cleared from memory. Next highest priority diagnostic trouble code stored (if one exists) will begin flashing.

The codes and clearing proceedure above are to be used as a guide, NO claims are implied as to the correctness or accuracy of either.

Sep 11, 2013 | Cars & Trucks

2 Answers

Code 65535 what does that mean


How do i remove t-mobile content lock with out credit card or by going to t-mobile shop.

Apr 05, 2013 | Cars & Trucks

1 Answer

Opel Vectra B, 00031 - Driver Airbag Squib Circuit High Resistance presence


It sounds like you have a bad clock spring unit located behind the steering wheel.What are the OBD11 codes.You have to be very carfull when servicing Air Bag systems you can set off the air bag and hurt yourself with static elec spark.

Oct 06, 2012 | 1988 Opel Vectra

2 Answers

Airbag light stays on in a 2003 audi a6 i've replaced airbag module & drivers seatbelt


You need to access the Airbag ECU (Electronic Control Module) using suitable diagnostic equipment connected to the data link connector of the car in order to erase all faults - DTC (Diagnostic Trouble Codes) memored, unlock and reset the Airbag ECU. Then the Airbag light will turn OFF after approx. 4 seconds, ignition ON.
Good Luck!

May 15, 2011 | Audi A6 Cars & Trucks

1 Answer

Flashing airbag light 4 blinks 6 blinks


This is a code 46 LH Crash Sensor - Not Mounted to Vehicle Properly. Often there is a poor contact on one of the wiring connectors. Some of the problems can happen from a poor connection where everything connects under the drivers side seat.
Here is a list of codes for the airbag light issues.

Air Bag Fault Code Table

AIR BAG DIAGNOSTIC MONITOR FAULT CODE PRIORITY TABLE

Priority Code Component/Fault Description

Highest -- No Air Bag Lamp - Inoperative Lamp Circuit or No Ignition Voltage to Diagnostic Monitor

' -- Continuous Air Bag Lamp - Diagnostic Monitor Disconnected or Inoperative

' 12 Low Battery Voltage

' 13 Air Bag Circuit or Crash Sensor Circuit - Shorted to Ground

' 21 Safing Sensor - Not Mounted on Vehicle Properly

' 22 Safing Sensor Output Circuit - Shorted to Battery Voltage

' 23 Safing Sensor Input Feed/Return Circuit Open

' 24 Open in Circuit 944B or Low Resistance in Crash Sensor(s)

' 32 Driver Side Air Bag/Safing Sensor Circuit - High Resistance or Open

' 33 Pin 7 Not Grounded at Diagnostic Monitor

' 34 Driver Side Air Bag/Safing Sensor Circuit - Low Resistance or Shorted

' 35 Low Resistance Across Pins 8 and 9 at Diagnostic Monitor

' 41 Crash Sensor Circuit - High Resistance or Open

' 44 RH Crash Sensor - Not Mounted to Vehicle Properly

' 45 Center Radiator Crash Sensor - Not Mounted to Vehicle Properly

' 46 LH Crash Sensor - Not Mounted to Vehicle Properly

' 51 Diagnostic Monitor Internal Thermal Fuse - Blown and Short to Ground No Longer Exists

' 52 Backup Power Supply - Voltage Boost Fault

' 53 Internal Diagnostic Monitor Fault

Lowest -- Rapid Continuous Flashing of Air Bag Lamp - All Crash Sensors Disconnected

Hope this helps...

May 05, 2011 | 2003 Ford Escape

2 Answers

My air bag light on my 2000 Ford Econoline van flashes a 19 code. Does anyone know what that means?


Seems to be a very common problem with Ford. The wiring harness beneath the drivers seat contains the sensors for the airbag system. Go under the drivers seat and secure all the wires and clips. This makes most error lights for the airbags go away. Hope this helps and good luck!

May 02, 2009 | 1996 Ford Aerostar Extended

1 Answer

Airbag flashes 10 times misses a flash then repeats


Try clearing the codes & see if it returns. I do not see a code fault 10. Starts at 12.

---------------------------------------------------------------------
Section 01-20B: Restraints, Passive — Supplemental Air Bag System 1995 Town Car, Crown Victoria, Grand Marquis Workshop Manual DIAGNOSIS AND TESTING Diagnostic Trouble Code Clearing Procedure to Clear Diagnostic Trouble Codes from Diagnostic Monitor Non-Volatile Random Access Memory.
Normal Operation
The air bag diagnostic monitor (14B056) continually checks the air bag system for readiness. When a fault condition is detected, the DTC associated with that fault is stored in the air bag diagnostic monitor's Non-Volatile Random Access Memory (NVRAM). After writing the DTC to NVRAM, the air bag diagnostic monitor signals the fault by flashing the appropriate diagnostic trouble code on the air bag indicator. The diagnostic trouble code written to NVRAM is permanently stored in the air bag diagnostic monitor until cleared by the diagnostic trouble code clearing procedure.
  • Upon each cycle of the ignition switch (11572) , the air bag diagnostic monitor checks for diagnostic trouble codes written in NVRAM. If any diagnostic trouble codes exist in NVRAM, the air bag diagnostic monitor will then check to see if these fault conditions are still present.
  • If the conditions of the diagnostic trouble code in NVRAM are still present, then the air bag diagnostic monitor will use the air bag indicator to flash out the diagnostic trouble code number that was written in memory.
  • If the conditions of the diagnostic trouble code are not still present (indicating an intermittent or serviced fault), the air bag diagnostic monitor will use the air bag indicator to flash out a DTC which is the sum of the diagnostic trouble code in NVRAM plus 40.
Example: Due to corrosion, high resistance develops on the driver side air bag circuit. The air bag diagnostic monitor stores a diagnostic trouble code 32 in NVRAM. Upon each cycle of the ignition switch , the air bag diagnostic monitor checks the resistance of the driver air bag circuit.
  • If the resistance is still high, the air bag diagnostic monitor causes the air bag indicator to flash out a DTC 32.
  • If the resistance falls within the normal range due to service or an intermittent condition, the air bag diagnostic monitor causes DTC 72 to be flashed on the air bag indicator.
Once a fault has been serviced, the associated diagnostic trouble code may be cleared from NVRAM. Only diagnostic trouble codes that the air bag diagnostic monitor sees as repaired or intermittent may be cleared (diagnostic trouble codes 52 and above). In no circumstances can hard fault conditions (diagnostic trouble codes 45 and below) be cleared.
  1. Follow the diagnostic procedures as outlined to service the fault condition flashing on the air bag indicator.
  1. Cycle the ignition switch to OFF and then to RUN.
  1. Observe air bag indicator prove-out (six ± two seconds) followed by diagnostic trouble code (52-85) flashing completely one time.
  1. Locate the Diagnostic "Trouble Code Clear" Connector located underneath the glove compartment (06010) containing Circuits 631 (T/R) and 57 (BK).
  1. Use a jumper wire to short Circuit 631 (T/R) to Circuit 57 (BK) or to another good ground. This short must be made after the diagnostic trouble code flashes completely one time, but before the warning light stays on continuously.
  1. Hold short until air bag diagnostic monitor tone sounds (approximately five seconds).
  1. Release short on Circuit 631 (TAN/RED STRIPE) to Circuit 57 (BLACK). This short must be released within 25 seconds after the diagnostic monitor tone sounds. Diagnostic trouble code is now cleared from NVRAM. Next highest priority diagnostic trouble code stored in NVRAM (if one exists) will begin flashing.

Feb 09, 2009 | 1995 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

146 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...