Question about Cars & Trucks

Open Question

What must the oil pressure on a 6g72 colt v6 3 liter 4x4 bakkie 1996 be

Posted by Anonymous on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

boscia
  • 163 Answers

SOURCE: 1996 vw jetta with 2.0 liter

thats really not a good sign. have you checked the oil lately?

Posted on Dec 14, 2008

  • 1779 Answers

SOURCE: no oil pressure

The oil pressure switch (also known as the oil press. sending unit) is located above the oil filter, mounted on the engine block. It is a $6 part in my area, just by chance if that's all that's wrong, I'd replace it. Hopefully it is that simple. If not, time for an oil pump? If u remove it, and crank the engine, there should be a steady flow of oil, if not then it's the pump. Good luck.

Posted on Jan 09, 2009

duane_wong
  • 6826 Answers

SOURCE: where is the oil pressure

Removal & Installation 4.8L, 5.3L & 6.0L Engine To Remove:

  1. Remove the engine sight shield. chevy_aval15_02-04_opcon.gif

  2. Disconnect the oil pressure sensor electrical connector. chevy_aval15_02-04_opsocket.gif

  3. Using J41712 sensor socket or equivalent, remove the oil pressure sensor.
To Install:
  1. Apply sealant GM P/N 12346004, (Canadian P/N 10953480), or equivalent, to the threads of the sensor.
  2. Using J41712 sensor socket or equivalent, install the oil pressure sensor. Tighten the sensor to 15 ft. lbs. (20 Nm).
  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine sight shield.
8.1L Engine To Remove:
  1. Remove the engine appearance cover.
  2. Disconnect the electrical connector from the oil pressure sensor.
  3. Use a special socket such as J 41712 to remove the sensor.
To Install:
  1. If installing the old sensor, apply sealant GM P/N 12346004 (Canadian P/N 10953480), or equivalent, to the threads of the sensor.
  2. Using J 41712 or equivalent, install the sensor. Tighten the sensor to 22 lb ft (30 Nm).
  3. Connect the oil pressure sensor electrical connector.
  4. Install the engine appearance cover.
prev.gif next.gif

Posted on Aug 05, 2010

melvi_99
  • 387 Answers

SOURCE: where is the oil pressure

oil pressure sender is located at the rear of engine, bank 1, if you are at top of engine you may access it a little bit right away from center rear side of engine, keep the engine cold if you want to remove it or replace, you need socket #27 when removing and rachet, or the special tool by gm J41712,

Posted on Aug 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Whtat is the function of oil pump balance shafts for colt bakkie


balance shafts are used to counter the harmonic vibrations of the crankshaft caused by power impulses as the pistons fire
without them , the engine will run unbalanced and will have problems in bearing wear and early engine failure

Feb 14, 2017 | Cars & Trucks

1 Answer

Differential oil


the correct oil is required
before answering people need to know
need maker of vehicle
if its a limited slip diff or standard diff
4x4 FWD RWD ?
maker of the diff

Sep 07, 2016 | Cars & Trucks

1 Answer

What is righ amount of oil i must put in the gearbox


if auto - the level on the dip stick
if manual remove the filler plug in the side of the box and the right amount is when the oil runs out of that fill hole
the oil level is at the thread s of the hole
if there are 2 plugs in the side of the box , remove both and put oil in the upper one until it runs out of the bottom hole replace plugs and do up tight.
point of interest
all manual boxes, transfer cases and diff oil levels are to the bottom of the fill hole thread.

Jun 20, 2015 | Cars & Trucks

2 Answers

What diff oil for a 3.0L mitsubishi colt 4x4 1999


Hi Shy Guy, The oil to use in a 4 X 4 differential should be a good quality EP 90, (Extreme Pressure), either synthetic or mineral. The same can be used in the gearbox, but you may find a slight beneficial fuel saving by using 70 w 85 gear oil in the gearbox. Regards John

May 02, 2014 | 2002 Mitsubishi Colt

1 Answer

Stil awaits an answer on colt bakkie engine overhaul


colt?
bakkie?
this a Toyota. corolla?
wrong forum?

Feb 04, 2014 | 1989 Toyota Corolla 2 Door

1 Answer

Where's the oil filter located on a 1996 gmc sierra 4x4 ?


On a 5.3 liter engine it is located just in front of the flywheek housing on the drivers side.

Apr 10, 2010 | 1996 GMC Sierra

1 Answer

Where is the oil sending unit on a 1996 ford taurus 3.0 liter engine located? glenn


On 3.0L OHV engines, the oil pressure sensor is located on the left side of the engine block above the flywheel. On 3.0L DOHC engines the sensor is located on the left side of the engine block above the oil filter. On 3.4L DOHC engines the sensor is screwed into the oil filter adapter. The oil pressure sensor operates the oil pressure warning lamp.

71f6e37.jpg
Fig. 1: Location of the oil pressure sensor-3.0L OHV engines


046f42b.jpg Fig. 2: Location of the oil pressure sensor-3.0L DOHC engines

69cce3e.jpg

Fig. 3. The oil pressure sensor-3.0L OHV engine

Hope help with this (remember rated this help). Good luck.

Feb 18, 2010 | 1996 Ford Taurus

1 Answer

Location of the oil pressure switch,(which acts as a fuel cut-off).


ford ranger 2000 4x4 3 liter where is locatet oil presure sensor

Oct 06, 2009 | 1996 GMC Sonoma

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...