Question about Suzuki XL7

1 Answer

Axle install how to replace cv boot cannot find axle

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Suzuki Master
  • 5,668 Answers

Now you can get one drive shaft.Nobody fix.

Posted on May 08, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: CV Axle removal and installation

The axle should be able to be removed by using a flat ended pry bar tool with a dull flat end. Or possibly a very large flat screw driver. Put the pry bar between the axle and transmission. With light pressure, the axle should pop out of the transmission. The axle just snaps into the transmission. There should be no need or cause to damage the seal because the seal is inset into the transmission. Just watch what you are doing. As far as replacing the seal, I do not know. I have not had to do that yet, and I have replaced both sides with new boots more than once.

Posted on Nov 11, 2008

  • 14 Answers

SOURCE: 94 Geo Prizm CV or driveaxle?

on this type of vehichle, you have two axles in the front; one going to each side. Chances are that the boot at the axle joint was torn and that is why you are having problem. In teh past people used to replace the boot, this day and age its actually cheaper to replace the axle. So you would need to replace that side of the axle (the half shaft).

Posted on Nov 20, 2008

  • 507 Answers

SOURCE: average repair cost for cv joint or axle replacement

Average time should be around 2-3 hours. Every shop charges different hourly rates. Dealerships will be around at least 80 an hour, smaller shops will run lower.

Posted on Jan 05, 2009

csmock132
  • 4669 Answers

SOURCE: how often to replace cv boots/cv joints/axle?

If something off the road tore the boot, yes but if it has not been tore long and you don't hear any clicking noises around corners, you can just replace the boot.

Posted on Mar 08, 2009

  • 10 Answers

SOURCE: installing cv axle on a 2004 impala

remove the tire, remove caliper and rotor remove 35mm nut and push cv joint into trans and remove

Posted on Dec 24, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Are cv boots replaceable


CV boots are replaceable,but most times it's just as cheap to replace the complete axle.

Jul 10, 2017 | Cars & Trucks

1 Answer

CV boot leaking


get a boot replacement kit remove axle from suspension and trans. clean old grease out of failed axle, stuff new grease into cv joint and put new boot on shaft close to joint. fill the boot with the rest of the tube of cv grease and install per instructions.

Nov 03, 2012 | 2003 Subaru Baja

1 Answer

Im trying to replace the driver side cv. the inner boot came off with the whole drive axcel, except for the inner spine. it looks lkike the previous owner removed the inner cv joint and replaced the boot...


YOU HAVE TO REMOVE WHOLE AXLE AN INSTALL AXLE IN INNER CV JIONT THEN MAKE SURE IT CLIPS IN,INSTALL BOOT AN RECLAMP CV BOOT WITH SPECIALLTY PLIERS

Dec 21, 2010 | Mazda 323 Cars & Trucks

2 Answers

Cv joint but the plastic thang that go around it


One would have to remove the half shaft to service the cv joint properly.

CV-Joints Overhaul Check the CV-boot for wear tccs7030.jpg

Removing the outer band from the CV-boot tccs7031.jpg

Removing the inner band from the CV-boot tccs7032.jpg

Removing the CV-boot from the joint housing tccs7033.jpg

Clean the CV-joint housing prior to removing boot tccs7034.jpg

Removing the CV-joint housing assembly tccs7035.jpg

Removing the CV-joint tccs7036.jpg

Inspecting the CV-joint housing tccs7037.jpg

Removing the CV-joint outer snapring tccs7038.jpg

Checking the CV-joint snapring for wear tccs7039.jpg

CV-joint snapring (typical) tccs7040.jpg

Removing the CV-joint assembly tccs7041.jpg

Removing the CV-joint inner snapring tccs7042.jpg

Installing the CV-joint assembly (typical) tccs7043.jpg

prev.gif next.gif

Oct 08, 2010 | 2004 Oldsmobile Alero

1 Answer

1997 Pathfinder How do you replace the left outer cv boot?


How to Replace a CV Boot
( DIY Complexity: Hard / Time: 3.2 hours )

Parts:
1. CV Boot
2. CV Boot Clamp Kit

Tools:
1. Mallet Hammer
2. 3/8 in. Drive Ratchet
3. Combination Wrench Set
4. Floor Jack
5. Flashlight
6. Flat Head Screwdriver
7. Socket Set
8. Tire Iron

Steps:
Step 1 Secure the vehicle on a level surface, making sure the vehicle will not roll or lean too much when jacked up.
o Tip: Safety Tip:Always wear safety glasses when working on your vehicle. Wear other personal protective equipment (PPE) when necessary, for example latex gloves or safety shoes.

Step 2 Lift up the front of the vehicle using a jack.
o Tip: Using an aftermarket floor jack, instead of the original equipment (OE) jack, can make the job easier and safer. Verify the condition of the floor jack before use.

Step 3 Secure the vehicle with jack stands on both sides for safety before starting any work. The pinch welds and the frame are the two best locations. Do not rely on the jack to hold the vehicle up while working.
o Tip: Try to find a flat, level, and strong surface to put the jack stands.

Step 4 Find the correct size socket and large ratchet or tire iron and turn the wheel lug nuts counter clockwise. Remove the front wheels.
o Tip: It is a good idea to try and break the lug nuts free before you jack the wheels off the ground. This way they you will not spin the front wheels or put stress on the transaxle.
o Tip: Lug nuts fasten the wheel to the hub and may be on very tight. To gain more leverage, use a breaker bar to loosen the nuts.

Step 5 Inspect the CV boot for damage.
o Tip: The CV joint may be worn if the boot is damaged. Thoroughly inspect the CV joint assembly before installing the new boot. If the CV joint is damaged, replace the entire CV joint axle assembly.

Step 6 Mark the axle for installation reference. Remove the CV joint axle assembly.

Step 7 Using a bench vise, hold the shaft of the CV joint secure so that you can separate the CV joint from the shaft. Remove the CV boot clamps.

Step 8 Slide the CV boot off the outer CV joint.

Step 9 Using a rubber mallet, knock the CV joint off of the axle shaft.

Step 10 Remove the old boot from the CV axle shaft and wipe off any old grease. Clean the sealing surface on the CV joint.

Step 11 Fill the CV joint with grease and get it ready to slide back onto the shaft.

Step 12 Slide the new boot onto the shaft but do not tighten the inner clamp yet. Install a new retaining clip before putting the joint and axle together.

Step 13 Slide the CV joint back onto the axle shaft completely.

Step 14 Pack the boot with grease and slide the boot over the CV joint housing. Secure the boot with new clamps.

Step 15 Install the CV joint and axle back into the vehicle in the reverse order that it was removed.

Step 16 Mount the wheel back onto the hub assembly.

Step 17 Tighten lug nuts in a star pattern and torque to suggested manufacturer specifications in the vehicle owner’s manual.

Step 18 Remove jack stands.

Step 19 Lower vehicle with jack until it is securely on the ground.

Step 20 Drive the vehicle to make sure that any noises are no longer present and that there are no indications of wearing parts. Before road testing, visually inspect the area you have worked on to make sure everything is tightened and assembled properly.

Hope help with this (remember rated and comment this help).

Mar 12, 2010 | 1997 Nissan Pathfinder

1 Answer

Need a diagram of the cv joint and cv boot installation for a 1998 dodge durango


If you are replacing cv joint the easiest thing is reman axle with two new cv joints and boots installed all you do is change axle good luck

Dec 23, 2009 | 1998 Dodge Durango

1 Answer

I have a 1999 isuzu 4wd rodeo 6 cylinder and was wondering if Need to install a new boot kit or if I need to replace the entire front left cv axle shaft. I had a tear in my rubber boot and noted some...


Do not try to get the cv axle out ot the axle housing. It is a major operation. Remove boot and disconnect the inner cv joint and save about five hours of time. The choice is yours ,boot or reman cv axle. You will need to take the reman. axle apart to install it though and some new clamps. Not a simple operation.

Sep 28, 2009 | 1997 Isuzu Rodeo

1 Answer

Hyundai 2005 Elantra cv boot replacement instructions.


There are no instructions available except with the purchase of SOME boot kits. Depending on the CV joint design, you may not be able to remove the joint from the axle. However, most Hyundai CV joints can be removed from the axle by using a drift and a 2 pound hammer to knock the joint off the axle. Once you've done this, it's a simple matter of removing the old boot and installing the new one w/fresh grease and tension bands. Otherwise, you have to remove the DOJ from the other end of the axle and replace the boot that way.

Aug 24, 2009 | 2005 Hyundai Elantra

1 Answer

Cv boot clamp came off somehow from the outer hub assembly


athere is a snap ring within the CV joint the nedds to be spread OPEN to release CV joint from axle, Once CV is cleaned and repacked with grease rintall onto axle by again spreading apart clamp. Prior to installing CV joint slide NEW CV joint boot onto axle, Cleanly intall add'l grrease and reinstall CV boot.

Apr 04, 2009 | 1996 Buick Century

1 Answer

Damaged cv boot on 2002 montana fwd ( boot near wheel)


In order to properly replace a C.V. boot you need to disassemble that side of the wheel assembly and drop the C.V. axle. The new boot(from parts house or Dealership goes right back on. You will need to clean the area really well and get all grit out because this is what damages the axle itself. Repack the boot with C.V. grease and you're on your way. It can be a tough job sometimes so I recommend investing in a repair manual(like Chilton) to ease the process. The parts houses sell what I call cheater boots now and basically it is a shorter term solution. They install by basically wrapping around the old boot area and then screw together. I installed one for a customer once at her request and it lasted about 10,000 miles. When she had more money she had me put the permanent one on. I will say this about these, if you can't do the permanent repair right away for whatever reason it sure can save a C.V. axle from being destroyed - temporarily. Good Luck

Jul 01, 2008 | 2002 Pontiac Montana

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...