Question about Ford Ranger

Open Question

Oil sending unit location on a 1989 ford ranger 2.3 liter

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

farroutideas
  • 78 Answers

SOURCE: oil pressure sending unit

Hi there;

Your looking foer the oil pressure sensor on the 2004 8.1L.
You will find it located directly behind the EGR valve threaded into the block just to the drivers side of the center bolt for the transmission to block connection.

Thanks
Farrout!

Posted on Mar 17, 2009

  • 43 Answers

SOURCE: Location of the Oil Pressure Sending Unit

On the drivers front of engine block below the cylinder head & gasket . Slightly behind waterpump.

Posted on Apr 15, 2009

  • 126 Answers

SOURCE: Where is the oil sending unit located on a 2003 Chevy Tahoe 5.3 engine

its in the block behind intake manifold .

Posted on May 05, 2009

big-dog420
  • 124 Answers

SOURCE: location of oil sending unit?

Drivers side about 3" from the back about 2" from the oil pan. Will have a single black wire leading from it to the wire harness
Hope this helps
Please leave feedback Thanks

Posted on Dec 24, 2009

c17hydro
  • 2984 Answers

SOURCE: Where is the oil pressure sending unit located on

Removal & Installation

  1. Disconnect the negative cable from the battery.
  2. Raise vehicle on hoist.
  3. Remove front splash shield.
  4. Disconnect oil pressure sender connector (4).
  5. Remove the pressure sender (2).
6eaedba.gif
Oil pressure sending unit


To install:
  1. Install oil pressure sender.
  2. Connect oil pressure sender wire.
  3. Install front splash shield.
  4. Lower vehicle.
  5. Connect the negative battery cable.

Posted on Jan 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the temperature sending unit on a 1989 ford ranger 2.3L


look for a small brass sender unit with normally 1 wire from it at the thermostst housing on the engine side of the housing

Jan 13, 2013 | 1989 Ford Ranger

1 Answer

Ford ranger 1989 firing order


Hi there:
1989 Ford Ranger 4WD 2.3 liter SOHC L4



8_16_2012_11_11_41_pm.gif


1989 Ford Ranger 4WD 2.9 liter V-6 VIN "T"

8_16_2012_11_12_18_pm.gif

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Aug 16, 2012 | 1989 Ford Ranger

2 Answers

Where is the oil pressure switch located on a 1987 ford ranger with a 2.9 L engine


2.9L and 4.0L engines-Left side front of the engine, below the cylinder head in the engine block.

Jul 02, 2010 | 1987 Ford Ranger

1 Answer

Low oil pressure on guage of my 89 ford ranger 6 cylinder


Could be low oil level, a bad sending unit, or actually low oil pressure due to a worn oil pump or worn bearings.

Mar 09, 2010 | 1989 Ford Ranger

1 Answer

Oil sending switch location on a1993ford ranger


most oil sending units are located on driverside rear of engine block or located right near or at oil filter

Mar 06, 2010 | 1993 Ford Ranger SuperCab

1 Answer

Where do you align timing marks on a 1989 ford ranger 2.3 liter


CLICK on the following LINK. It has the Timing Mark Diagrams you will need.
If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

http://www.2carpros.com/car_repair_information/year/1989/make/ford/model/ranger/1989_ford_ranger_timing_belt_diagram_marks.htm

Feb 28, 2010 | 1989 Ford Ranger

2 Answers

Location of oil sending unit? on a 1990 ford ranger with a 2.3l


Drivers side about 3" from the back about 2" from the oil pan. Will have a single black wire leading from it to the wire harness
Hope this helps
Please leave feedback Thanks

Dec 24, 2009 | 1990 Ford Ranger SuperCab

1 Answer

Where is the oil pressure sending unit on a 1988 ford ranger 2.3 liter?


Left rear of cylinder head, by where it bolts to tranny.

Nov 14, 2009 | 1988 Ford Ranger

1 Answer

1989 Ford Ranger 2.9 liter 4x4 Runs Horrible


change fuel filter. add can of SEAFOAM(parts house) to fuel. It sounds like the beginning of EGS(ethanol gas syndrome). corn liquor substance, water, and clogging. all caused by ethanol fuel.

Sep 02, 2009 | 1989 Ford Ranger

2 Answers

Location of the Oil Pressure Sending Unit on a 2001 Ford F-150 V-6 4.2 liter


On the drivers front of engine block below the cylinder head & gasket . Slightly behind waterpump.

Apr 14, 2009 | Ford F-150 Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

fordexpert

Level 3 Expert

5495 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...