Question about 1990 Buick Century

Open Question

Wiring diagrams Service warning reset

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i rewire a warn 12v 8000lb winch


There are lots of links on the internet to wiring diagrams; just make sure they match the winch you have
warn 8000 lb winch wiring diagram Google Search

Feb 01, 2015 | Cars & Trucks

1 Answer

1996 ford explorer headlamp wiring


You can go to www.bbbind.com an get free wiring diagrams an TSB's Technical Service Bulletins Click on Technical Information then Technical Service Bulletins & Wiring Diagrams - Then you will see this END-USER LICENSE AGREEMENT , go to bottom of the page an click on I Agree next page you'll see this ..
  • TSBs
  • Wiring Diagrams
  • Search Technical Service Bulletins

    Year 2015 2014 2013 2012 2011 2010 2009 2008 2007 2006 2005 2004 2003 2002 2001 2000 1999 1998 1997 1996 1995 1994 1993 1992 1991 1990 1989 1988 1987 1986 1985 1984 1983 1982 1981 1980 Make Model System Subsystem


    ' Reset
    Powered by Longwood enter your vehicle info

    Jan 19, 2015 | 1996 Ford Explorer

    1 Answer

    Airbag light reset code


    You would need to reset the warning light and then see if it comes back on, which would indicate a fault still there. Try this procedure

    http://s16.photobucket.com/user/rogersb/media/AirBagReset.jpg.html

    "How do you reset the airbag warning light in a '94 Camry?
    A: Clearing the warning light in '92-'96 Camrys by the following procedure:
    In the DLC1 or DCL2 (data link connector under the hood, see following diagram)
    Use two short wires, one wire at terminal TC and a different wire at terminal AB
    With the ignition key ON - wait 6 seconds, then:
    Ground terminal TC to good body ground for one second
    Then ground terminal AB for one second
    Then TC one second
    Then AB one second
    Then ground TC until the light blinks.
    Make sure the interval between grounding terminals is not more than 0.2 sec.
    Remove the ground wires
    Be very careful to only use the correct terminals."

    Jan 21, 2014 | Toyota Cars & Trucks

    1 Answer

    Reset service indicator on a volvo s40 t4 99 model


    Ensure all doors are closed.
    Turn ignition into position I.
    Press and hold reset button [A] (shown in diagram).
    Immediately turn ignition key into position II (within 2 seconds).
    Keep button [A] depressed until service message has been reset.
    A yellow warning light [B] (in diagram) will illuminatewhen it's time to release the button.
    Release button [A] within 4 seconds. There will be an audiblesignal when the reset is complete. If reset button is not released within 4 seconds, the service interval indicator will not be reset.8474eea3-977f-4ecc-b123-2479d0f46c3c.jpg

    Aug 13, 2013 | Cars & Trucks

    2 Answers

    My dash lights will not work how can I fix this


    Do you have any mileage programmer, use the to reset the dash system.

    Jul 31, 2013 | 1988 Mercury Tracer

    1 Answer

    My bmw z3 service engine light is on and the codes show P1899 and P1898. can you help


    Error codes not in service manual. presumme dealers can assist you with a pnhonecall for error codes.

    BMW SERVICE RESET

    Take a small wire, paperclip, or elect wire and bend like a horseshoe. No light or equipment necessary Open the diagnostic data port, the one were the little pacman centre is located. Turn the ignition to position 2, don’t start. Connect pin7 always first and then pin 19. Hold for 4 seconds. Remove wire and settings will be reset. Warning if you hold the wire longer than 10 seconds you may reset inspection intervals 1 and 2.

    I’ve done this twice and it definitely work on my E36

    Aug 12, 2009 | 1998 BMW Z3 Roadster

    1 Answer

    Electronics problem


    Get a service manual with wiring diagram.
    Check your ground wires for good contact.

    May 09, 2009 | 2000 Volkswagen Beetle

    1 Answer

    Car audio wiring diagram for 1998 volvo s-70


    CLICK HERE for your vehicles full service manual. If you are cutting wires.
    Be warned your vehicle has a factory amplifier installed, and needs to be bypassed to hear the speakers if you are just wiring behind the dash.
    Metra makes a harness you install on the aftermarket radio, then simply plug into the vehicle's harness.
    All the wires are labeled for easy installation.

    70-9220 is the metra part number. Click on the number to see an eBay auction.


    Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

    Apr 09, 2009 | 1998 Volvo S70

    1 Answer

    BMW 5 series - 2005 model - resetting service & waring lights


    the brake pad warning light is controlled by a sensor located in the front and rear brake pads, small contact with 2 wires that plud into a harness, if they are bad I think the replacement cost is around 5-10 dollars for a new one, there will only be one in the front and one in the rear, the service light is turned out by a special tool at the dealer

    Mar 27, 2009 | 1991 BMW 5 Series

    Not finding what you are looking for?
    1990 Buick Century Logo

    Related Topics:

    140 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Buick Experts

    yadayada
    yadayada

    Level 3 Expert

    76630 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8514 Answers

    Are you a Buick Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...