Question about Cars & Trucks

1 Answer

Ford Bantam bakkie 1.6I 2002 (Old shape)

Can you please give me advise as how to replace a Clutch Master Cylinder kit

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 14 Answers

Its better you give it to a mechanic because it is very complicated (as a mechanic im telling you this )

Posted on May 07, 2013

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1596 Answers

SOURCE: How do I bleed the clutch master cylinder

Same as You Bleed Any other System Being carefull not to get air IN and IT sometimes TAKES FOREVER ________ STICK WITH IT ------ Took Me 2 hours One time

Posted on Jan 19, 2009

  • 10 Answers

SOURCE: ford focus st170 clutch master cylinder

To replace the clutch master, you must remove the under hood fuse box and air filter housing assm, then remove the hydraulic line that goes into the inlet port of the clutch master, then inside the car, remove the hush panel/knee bolster panel from under the steering column, and loosen the boilts that retain the brake pedal to the firewall, then remove the two 10mm bolts that secure the clutch master to the brake pedal assm. Reverse procedure ti install, then fill the brake master cylinder with clean fluid, loosen the bleeder screw at the top of the trans, and bleed the clutch as you would the regular brake system, but never pump the pedal, tighten screw, with foot off of clutch pedal open screw and press pedal to floor, then tighten screw before you release pedal, then release pedal loosen screw, etc. until no more air comes out, it may take quite a few times to fully bleed the system.

Posted on Feb 07, 2009

motor1258
  • 6674 Answers

SOURCE: install a clutch kit

This link may help.

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528018f027

Posted on Feb 27, 2009

  • 70 Answers

SOURCE: no clutch pedal been bleeding it for 3 days

these are notorius for clutch bleeding problems, there is no good answer other than to keep pumping that pedal, eventually it will bleed out

Posted on Dec 06, 2009

  • 2 Answers

SOURCE: problems with clutch master cylinder on a suzuki

I too am having problems with my 2006 GV clutch master cylinder. I noticed gradually over several weeks the gears and clutch pedal were degenerating and then the cluth gave completely. My mechanic took a look around and said the cylinder is the cheapest one he has ever seen, it's just a piece of plastic apparently! Is going to hopefully get the part this week or next, though he said as it's such a cheap and nasty part its likely it will happen again in the future. Not happy!

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where do I find a workshop manual for a 2007 Ford Bantam?


Look up Tradebit on web,get a 2002--2008 manual download.
Anthony.

Sep 19, 2016 | 2007 Ford Bantam 1.3i

1 Answer

I got a ford bantam bakkie. Wen I drive and comes to stoping, so I brake and gear down to 2nd. If I should pull away in 2nd the bakkie either jerks or the revs feels a bit delayed. Question is can it be a...


sounds to me like the clutch plate is just a little worn. its a good way to test a clutch take off in 1st, 2nd on clutch power and see how it responds.

Jul 23, 2014 | Cars & Trucks

2 Answers

How do I fix the clutch slave cylinder on a Ford Bantam 1.3 2007?


we replace it when bad. (leaks)
are you asking all steps. R&R

Jun 23, 2014 | 2007 Ford Bantam 1.3i

1 Answer

Ford bantam diesel bakkie 2004


check the vaccuum pipe to the brake booster ,sounds like the booster is not receiving vacuum to power assist your brakes

Jan 15, 2014 | Cars & Trucks

2 Answers

Where do i get clutch master cylinder in my ford bantum


Try a used auto parts place. Try Denton Auto Salvage at 785-437-2223

Jan 03, 2014 | 2006 Ford Bantam 1.3i

1 Answer

No clutch on bakkie -how to you solve this


If you have a hydraulic clutch Then best bleed out the air in the system. If there is no air then replace the clutch master cylinder.

Aug 15, 2013 | 2005 Ford Bantam 1.3i

2 Answers

How to bleed n Clutch system on Ford Bantam 1.3


I have a Ford Bantam 1.3 bakkie and the clutch fluid is running / leaking into the vehicle itself. How do we replace?

May 03, 2012 | 2006 Ford Bantam 1.3i

1 Answer

Clutch problem


I guess the clutch system must be a hydraulic one, check the clutch master cylinder and slave cylinder if they are functioning.
If they are thn theres a problem with the clutch pressure plate, if thts so , you will have to drop the gear box to replace it and its adviseable to replac e the pro-kit...consisting of Clutch pressure plate, clutch plate and release bearing.

May 06, 2009 | Ford F Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

60 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...