Question about Cars & Trucks
2000 oldsmobile alero that won't start all the lights come on but there is no fire when you turn the key.
No spark first check ignition fuse.if fuse okay problem could be faulty ignition module or crankshaft position sensor.you can use a scanner check see if you you engine rpms on the scanner as the engine turn over
Posted on May 07, 2013
Check fuse,could be starter.check battery connection, how old is battery.
Posted on May 07, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
i have a 2000 alero new fuel pump and filter head gasket set plugs wires coil pack and converter is fine 1500rpms max have to let off to shift no power has good days and now will barely run 10mph max
Posted on Dec 21, 2008
Does your keyless remote works? Good connection from battery (-) to ground (black cable)? Also the imobilizer can be faild sometimes (antitheft)
Posted on Feb 24, 2009
Check out this recall below:
Bulletin No.: 04098A
04098 - Special Policy Adjustment - Turn Signal/Hazard Warning Flashers
Some customers of 1999-2002 Chevrolet Malibu, Oldsmobile Alero, Pontiac Grand Am, and 1999 Oldsmobile Cutlass may have turn signal/hazard flashers that become inoperative.
Special Policy Adjustment
This special policy covers the condition described above for a period of 10 years or 150,000 miles (240,000 km), whichever occurs first, from the date the vehicle was originally placed in service, regardless of ownership. The repairs will be made at no charge to the customer.
Good luck and hope this helps:
HAZARD WARNING SWITCH REPLACEMENT - ON VEHICLE
Remove the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent.
Remove the instrument panel cluster.
Remove the hazard warning switch bezel from the instrument panel using a small-flat bladed tool to release the retainers.
Remove the left side bolt from the hazard warning switch through the instrument panel cluster pocket Remove the right side and center lower bolts from the hazard warning switch through the center air louver deflector pocket.
Reposition the hazard warning switch from the instrument panel to access the electrical connector.
Disconnect the electrical connectors from the hazard warning switch.
Remove the hazard warning switch from instrument panel.
Connect the electrical connectors to the hazard warning switch.
Position the hazard warning switch to the mounting points in the instrument panel. NOTE: Refer to Fastener Notice in Service Precautions.
Install the left side bolt to the hazard warning switch through the instrument panel cluster pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) .
Install the right side and center lower bolts to the hazard warning switch through the center air louver deflector pocket. Tighten Tighten the left side hazard warning switch bolt to 3 N.m (27 lb in) .
Install the hazard warning switch bezel to the instrument panel pressing into place until fully seated. Install the instrument panel cluster.
Install the center air louver deflector. Refer to Air Deflector Louver Replacement - Center Vent.
Posted on May 24, 2009
Tips for a great answer:
Dec 25, 2015 | Cars & Trucks
Apr 04, 2015 | 2000 Oldsmobile Alero
Dec 30, 2012 | 2002 Oldsmobile Alero
Oct 16, 2012 | 2003 Oldsmobile Alero
Jul 13, 2012 | 2000 Oldsmobile Alero
Apr 19, 2012 | 2000 Oldsmobile Alero
Nov 27, 2011 | 2001 Oldsmobile Alero
Jul 23, 2011 | 2003 Oldsmobile Alero
Jul 05, 2010 | 2000 Oldsmobile Alero
Mar 07, 2010 | 1999 Oldsmobile Alero
219 people viewed this question
Usually answered in minutes!