Question about Cadillac Eldorado

Open Question

How to remove , remove the exhaust crossunder pipe

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to remove the exhaust manifold on the right side of a 94 4.9l engine in a cadillac deville. It has a broken bolt in the exhaust. What is involved in removing the manifold?


I suggest you use all new exhaust manifold hardware and torque new bolts to 20 Ft Lbs.
4.5L and 4.9L Engines
RIGHT
Disconnect the negative battery cable. Remove the air cleaner. Remove the exhaust crossover pipe. Disconnect the oxygen and coolant temperature sensors. Remove the catalytic converter-to-AIR pipe clip bolt. Remove the upper manifold-to-cylinder head bolts. Raise and safely support the vehicle. Disconnect the converter air pipe bracket from the stud and remove the converter-to-manifold exhaust pipe. Support the engine cradle with screw jacks and remove the rear cradle bolts. Loosen the front cradle bolts and slightly lower the Engine cradle. Remove the remaining exhaust manifold-to-cylinder head bolts, the AIR pipe, and the manifold. Clean the gasket mounting surfaces.
To install:
Install the exhaust manifold and replace the AIR pipe. Tighten the manifold mounting bolts to 16-18 ft. lbs. (21-24 Nm). Install the manifold-to-converter exhaust pipe and replace the converter air pipe bracket to the stud. Raise the Engine cradle and install the rear cradle bolts. Tighten to 75 ft. lbs. (102 Nm). Lower the vehicle. Replace the upper manifold-to-cylinder head bolts. Replace the converter air pipe to AIR pipe clip bolt. Connect the coolant temperature and oxygen sensor connectors. Replace the exhaust crossover pipe. Replace the air cleaner and connect the negative battery cable. Start the Engine and check for leaks.

Mar 28, 2017 | Cadillac Cars & Trucks

1 Answer

Having a promblem taking off crossover exhaust pipe on a 2005 Buick rendezvous I tooken off the two front exhaust Then took bottom two bolt . But still fasten to something is there other bolts...


Thermostat? engine cooling?
2 engines, here, LYA adn LY7.
nobody here posts engine, why do that?
so ill post only for 1.
the LA1
here are the steps.
NO FSM Sux huh? nor an alldata.com account, why not that? 15 bucks?


STAT out.
Remove the air cleaner and duct assembly. Refer to Air Cleaner Assembly Replacement in Engine Controls - 3.4L.

Drain the coolant until the coolant level is below the thermostat. Refer to Cooling System Draining and Filling (Refer To List 1) .

Remove the crossover exhaust pipe. Refer to Exhaust Crossover Pipe Replacement (Refer To List 2) in Engine Exhaust.

Remove the radiator hose from the thermostat housing.

Remove the thermostat housing bolts and clean any sealer from the bolt threads.

Remove the thermostat housing and gasket.
remove STAT
next is crossover page.

Disconnect the battery ground (negative) cable. Refer to Battery Negative Cable Disconnection and Connection (Refer To List 1) in Engine Electrical.

Remove the throttle body air inlet duct.

Drain the coolant from the cooling system. Refer to Cooling System Draining and Filling (Refer To List 2) in Engine Cooling.

Remove the inlet radiator hose from the engine. Refer to Radiator Inlet Hose Replacement (Refer To List 3) in Engine Cooling.

Remove the thermostat bypass pipe. Refer to Thermostat Bypass Pipes Replacement in Engine Cooling.



Remove the exhaust crossover heat shield bolts.

Remove the exhaust crossover heat shield.
  1. Remove the exhaust crossover pipe studs/nuts.
  2. Remove the exhaust crossover pipe.

end , remove.

now the bypass pipe FWD cars SUCK
  1. Disconnect the left engine mount strut from the engine.
  2. Remove the heater hose from the bypass pipe.
  3. Remove the thermostat bypass pipe to throttle body nut.
  4. Use the J 38185 in order to remove the thermostat bypass pipe hose clamps (1,5).
  5. Remove the thermostat bypass pipe to cylinder head nut (3).
  6. Remove the thermostat bypass pipe bolt (4).
  7. Remove the thermostat bypass pipe hose.
  8. Remove the thermostat bypass pipe.
sigh.....
why not log in to alldata.com
read the page then ask ques tons that are not clear.
and next time post the engine type.
above is just 1 engine.

Jun 18, 2014 | Cars & Trucks

1 Answer

How to replace water pump on 1991 pontiac quad 4


2.3L Engine
  1. Disconnect the negative battery cable
  2. Detach the oxygen sensor connector.
  3. Properly drain the engine coolant into a suitable container. Remove the heater hose from the thermostat housing for more complete coolant drain.
  4. Remove upper and lower exhaust manifold heat shields.
  5. Remove the bolt that attaches the exhaust manifold brace to the manifold.
  6. Break loose the manifold to exhaust pipe spring loaded bolts using a 13mm box wrench.
  7. Raise and safely support the vehicle. NOTE: It is necessary to relieve the spring pressure from 1 bolt prior to removing the second bolt. If the spring pressure is not relieved, it will cause the exhaust pipe to twist and bind up the bolt as it is removed.
  8. Remove the manifold to exhaust pipe bolts from the exhaust pipe flange as follows:
    1. Unscrew either bolt clockwise 4 turns.
    2. Remove the other bolt.
    3. Remove the first bolt.
  9. Pull down and back on the exhaust pipe to disengage it from the exhaust manifold bolts.
  10. Remove the radiator outlet pipe from the oil pan and transaxle. If equipped with a manual transaxle, remove the exhaust manifold brace. Leave the lower radiator hose attached and pull down on the outlet pipe to remove it from the water pump.
  11. Carefully lower the vehicle.
  12. Remove the exhaust manifold, seals and gaskets.
  13. Loosen and reposition the rear engine mount and bracket for clearance, as required.
  14. Remove the water pump mounting bolts and nuts. Remove the water pump and cover assembly, then separate the two pieces.

Feb 23, 2012 | 1991 Pontiac Grand Am

1 Answer

My husband and I are trying to get to our thermostat to change in my 2002 rendezvous, but there is a metal pipe in the way that we can't figure out how to remove. just behind the pipe, is a metal plate...


Hello vocalviixen,

The pipe that you referred to is the exhaust crossover pipe. Below I've included removal and installation instructions.

Also, the procedure for bleeding the coolant system is critical; if you need those instructions please post the question.

REMOVAL PROCEDURE
1. Disconnect the battery ground (negative) cable.
2. Remove the throttle body air inlet duct.
3. Drain the coolant from the cooling system.
4. Remove the inlet radiator hose from the engine.
5. Remove the thermostat bypass pipe.
6. Remove the exhaust crossover heat shield bolts.
7. Remove the exhaust crossover heat shield.
8. Remove the exhaust crossover pipe studs/nuts.
9. Remove the exhaust crossover pipe.
INSTALLATION PROCEDURE
1. Install the exhaust crossover pipe.
2. Install the exhaust crossover pipe studs/nuts.
3. Tighten the exhaust crossover pipe studs/nuts to 18 lb ft.
4. Install the exhaust crossover heat shield.
5. Install the exhaust crossover heat shield bolts.
6. Tighten the exhaust crossover heat shield bolts to 89 lb in.
7. Install the thermostat bypass pipe.
8. Install the inlet radiator hose to the engine.
9. Fill the cooling system with engine coolant.
10. Install the throttle body air inlet duct.
11. Connect the battery ground (negative) cable.


Regards,
netvan

Mar 14, 2011 | 2002 Buick Rendezvous

1 Answer

How to replace the exhaust manifold ring in my 91 Toyota Tercel


There is a bracket that attaches the exhaust pipe to the engine block. Remove the 2 screws that hold
that bracket on. I think they are 12mm heads. Detach the 2 exhaust manifold to exhaust pipe screws,
the screws have 15mm heads. A 15mm deep socket is best. After you remove those 2 15mm screws you can pull the exhaust pipe down, remove the old exhaust flange and put the new one on.

Rettach the exhaust manifold to pipe screws, and reattach the bracket and youre done.

Mar 07, 2011 | 1991 Toyota Tercel

1 Answer

What are the torque specs for 1996 Buick Century 3.1 L intake manifold?


Front Pipe REMOVAL & INSTALLATION Pipe Without Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal..
  2. Raise and support the front of the vehicle on jackstands.
  3. Remove the exhaust pipe-to-manifold nuts.
  4. Support the catalytic converter, then disconnect the pipe from the converter. Remove the pipe.
  5. Remove the exhaust gaskets. To install:
  6. Be sure to use all new gaskets when required. Assemble the system, check the clearance and tighten the bolts to about 15-30 ft. lbs. (20-41 Nm). Fig. 1: Front exhaust pipe connection common on vehicles with the catalytic converter not included 86813320.gif

  7. All clamps should be tightened to about 18-25 ft. lbs. (24-34 Nm). Do overtighten the clamps. If pipes become dented they can leak.
Pipe With Catalytic Converter
  1. Before removing any component of the exhaust system, always squirt a liquid rust dissolving agent onto the fasteners for ease of removal.
  2. Raise and support the vehicle.
  3. On some vehicles you will need to remove the brace from the transaxle.
  4. Remove the exhaust pipe nuts from the manifold.
  5. Support the catalytic converter pipe bolts from the rear of the converter.
  6. Lower the catalytic converter/front pipe assembly from the vehicle. To install:
  7. Be sure to use all new gaskets when required.
  8. Attach the new catalytic converter/front pipe assembly to the vehicle. Tighten the pipe to manifold nuts to 20-40 ft. lbs. (27-55 Nm).
  9. Attach the bolts at the rear of the catalytic converter/front pipe. Tighten them to 30-35 ft. lbs. (41-47 Nm).
  10. Connect the brace at the transaxle if removed.
  11. Lower the vehicle. prev.gif next.gif

Dec 18, 2010 | Buick Century Cars & Trucks

1 Answer

I want to know how change my oil pan gasket.


The oil pan gasket is a complex task. Due to the design of the Northstar engine,ie the exhaust crossunder exhaust pipe either the engine has to be removed from the car or remove the transmission.... The oil pan is a two piece assembly. Upper and lower. Yhank you

Sep 03, 2010 | 1999 Cadillac DeVille

1 Answer

How do i change my thermostat on my 2001 pontiac aztek. also how do i remove the crossover exhaust pipe to get to the @#$%^ing thing?


Exhaust Crossover Pipe Replacement
Removal Procedure
  1. Disconnect the battery ground (negative) cable.
  2. Remove the throttle body air inlet duct.
  3. Drain the coolant from the cooling system.
  4. Remove the inlet radiator hose from the engine.
  5. Remove the thermostat bypass pipe.
  6. Remove the exhaust crossover heat shield bolts.
  7. Remove the exhaust crossover heat shield.
89160026

  1. Remove the exhaust crossover pipe studs/nuts.
  2. Remove the exhaust crossover pipe.
  1. Remove the air cleaner and duct assembly.
  2. Drain the coolant until the coolant level is below the thermostat.
  3. Remove the crossover exhaust pipe.
  4. Remove the radiator hose from the thermostat housing.
  5. Remove the thermostat housing bolts and clean any sealer from the bolt threads.
  6. Remove the thermostat housing and gasket.
Removal Procedure

89153578

Dec 11, 2009 | 2003 Pontiac Aztek

1 Answer

How do I replace the oil pan gasket on a 2001 GMC Yukon XL?


Changing the oil pan gasket on a GMC Yukon XL is realtively simple, but does require removal of the exhaust pipe. You will need a new oil pan gasket and a new exhaust pipe flange gasket.
Put the car on ramps or jacks to access the undercarriage.
Remove the exhaust pipe by removing the 3 nuts holding the exhaust pipe flange to the exhaust manifold. These nuts often rust and prior application of penetrating oil may be required to remove them without damage. Once the pipe is unbolted, work the exhaust system loose from the hanging brackets. In most cases the entire system does not have to be removed since there is enough room to remove the pan with only the front hangers removed.
Drain the oil from the engine
Remove the 10 mm bolts holding the pan to the block.
Remove the old gasket material and scrape any remaining gasket from the block and pan.
Install the new gasket. Forma-Gasket or a similar product may be used in small quantities to "glue" the new gasket in place and prevent shifting while the pan is reattached to the block.
Reinsall the 10 mm bolts in a cross pattern to ensure the gasket is compressed evenly. Do not overtighten the bolts.
Replace the pipe to flange gasket between the exhaust pipe and the exhaust manifold with a new part.
Reattach the exhuast pipe to the hangers.
Install the 3 bolts connecting the pipe flange to the exhaust manifold.
Fill the engine with oil.

Sep 15, 2009 | 2001 GMC Yukon

2 Answers

05 susuki forenza


Removal Procedure
1. Disconnect the negative battery cable.
2. Drain the engine oil from the engine crankcase.
3. Remove the exhaust flex pipe retaining nuts from
the exhaust manifold.
4. Remove the exhaust flex pipe retaining nuts from
the catalytic converter or the connecting pipe.
5. Remove the exhaust flex pipe.
6. Remove the oil pan flange–to–transaxle retaining
bolts.
7. Remove the oil pan retaining bolts.
8. Remove the oil pan from the engine block.
Cleaning Procedure
1. Clean the oil pan sealing surface.
2. Clean the engine block sealing surface.
3. Clean the oil pan retaining bolts.
4. Clean the oil pan attaching bolt holes in the engine
block.
5. Clean the oil pan scraper.
Installation Procedure
1. Coat the new oil pan gasket with sealant.
Important : Install the oil pan within 5 minutes after applying
the liquid gasket to the oil pan.
2. Install the oil pan to the engine block.
3. Install the oil pan retaining bolts.
Tighten
Tighten the oil pan retaining bolts to 10 NSm (89 lb–in).
4. Install the oil pan flange–to–transaxle retaining
bolts.
Tighten
Tighten the oil pan flange–to–transaxle bolts to 40
NSm (30 lb–ft).
5. Install the exhaust flex pipe.
6. Install the exhaust flex pipe retaining nuts to the
exhaust manifold.
Tighten
Tighten the exhaust flex pipe–to–exhaust manifold
retaining nuts to 35 NSm (26 lb–ft).
7. Install the exhaust flex pipe retaining nuts to the
catalytic converter or the connecting pipe.
Tighten
Tighten the exhaust flex pipe–to–catalytic converter
or connecting pipe retaining nuts to 35 NSm (26 lb–ft).
8. Connect the negative battery cable.
9. Install the oil pan drain plug.
Tighten
Tighten the oil pan drain plug to 35 NSm (26 lb–ft).
10. Refill the engine crankcase with engine oil.

Jun 14, 2008 | 2005 Suzuki Forenza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cadillac Experts

yadayada
yadayada

Level 3 Expert

74896 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7688 Answers

Are you a Cadillac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...