Question about Cars & Trucks

1 Answer

Cruise control problem

Cruise control is not working. Message on – Cruise control inoperative

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 26 Answers

Sounds like you have a speed sensor gone bad

Posted on May 06, 2013


6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

robshow
  • 367 Answers

SOURCE: 2004 KIA Optima

Check the fuses for these items they could be blown.

Posted on Jan 07, 2009

  • 206 Answers

SOURCE: Cruise control inop

Could be a bad vacum dump switch on the brake pedal. There is 2 switches on the brake pedal one for brakes lights and one for cruise The cruise switch must be pushed when the pedal is up. Or your servo under the hood is bad To identify the parts go to the parts store and look at them and you will know what to look for

Posted on Mar 29, 2009

  • 277 Answers

SOURCE: poor fuel mileage, cruise control inop, a/c inop

First reaction to this one is;-

Engine Oil, Fuel ,Air and OIL Filter change, check and gap, or replace Spark plugs, then comeback later with the Results and continue on from there, with the other problems, No point in having CC and A/c, if the car is running junk on gas miles per gallon.

Regards, DT

Posted on Aug 25, 2009

  • 1 Answer

SOURCE: 2003 expedition cruise control inoperative no

I'm having the same issue with mine. Just checked both fuses #5 and #12 under the dash, but both are fine. Can't find Relay #302 for the speed servo. 2003's aren't listed in the recall. Ugh!

Posted on Dec 11, 2009

johnjnail
  • 1702 Answers

SOURCE: 2005 Ford taurus cruise control inoperative.

there are 4 fuses that are used to power up different parts of the cruse system all are in the inside fuse box ( under the left side of the dash ) fuse #32 10amp, fuse #27 10amp, fuse #17 15amp, fuse #38 15amp, the main unit fuse is the #32.

hope this helps.

Posted on Mar 12, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 trailblazer cruise control not working or the cruise control light not working


Which engine does your trailblazer have 5.3 or 4.2 L
Cruise Control Description and Operation (5.3L)
Cruise Control Description and Operation (4.2L)
makes a difference ! The best way to start diagnostic's is with a scan tool . May have DTC'S diagnostic trouble codes .
DTC P1574 Stop Lamp Switch Circuit
DTC P0568 Cruise Control Set Switch Circuit
DTC P0567 Cruise Control Resume Switch Circuit
Plus with a scan tool you can see if the cruise control switch is inputing to PCM. Data list .
The cruise control resume/accel switch is an input to the powertrain control module (PCM). The PCM uses the cruise control resume/accel switch signal circuit in order to detect when the driver has requested to accelerate the set vehicle speed or to resume the cruise control system. The PCM detects a voltage signal on the cruise control resume/accel switch signal circuit when the switch is applied. This DTC sets if the PCM senses voltage on the cruise control resume/accel switch signal circuit for longer than 90 seconds.
Cruise Control Indicator Inoperative (4.2L)
Turn OFF the ignition.
Install a scan tool.
Turn ON the ignition, with the engine OFF.
With the scan tool, Command the Cruise Control Lamp Test parameter ON, in the instrument panel cluster (IPC) Output Controls.
Does the Cruise indicator illuminate in the IPC?
YES - Go to Step 3
no - Go to Step 4
3
Inspect for poor connections at the harness connector of the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
YES - Go to Step 7
NO - Go to Step 6
4
Inspect for poor connections at the harness connector of the IPC. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
YES - Go to Step 7
NO - Go to Step 5
5
Replace the IPC. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?
YES - Go to Step 7
--
6
Replace the PCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?
Go to Step 7
--
7
Operate the system in order to verify the repair.
Does the system operate properly?
System OK
Go to Step 2

Cruise Control Inoperative/Malfunctioning (4.2L)

Install a scan tool.
Turn ON the ignition, with the engine OFF.
Press the cruise ON/OFF switch OFF.
With the scan tool, observe the Cruise ON/OFF switch parameter in the powertrain control module (PCM) Cruise Control Data list.
Does the Cruise ON/OFF switch parameter display OFF?

Your best bet mite be to take your vehicle to the dealer .

Dec 24, 2016 | Cars & Trucks

1 Answer

How to figure out problem with Cruise Control for repairing system myself?


the biggest thing with cruise control is to make sure all teh brake lights work. They shut the cruise down is inop

Jan 18, 2010 | 1999 Chevrolet Blazer

1 Answer

Why does my crise control not wotk


it can be a number of things, first i would make sure your brake lights work,on some vehicles if your brake lights are inop the cruise is inop, check the bulbs, fuses,brake lightswitch,if all are good, it could be the cruise control module, that could get technical.

Oct 11, 2009 | 1998 Dodge Caravan

1 Answer

Cruise control not working


Check your brake lights. In some cars, an inoperative brake light will prevent the cruise control from working.

Oct 10, 2009 | 1993 Toyota Corolla

1 Answer

Cruise coontrol inoperative


check your fuses. If it quit working immediately after the recall work then you need to take it back and make them fix it.

Oct 07, 2009 | 2005 GMC Canyon

1 Answer

Cruise control does not work


Have you had this campaign done yet?

06030: Product Safety - Brake Lamps Inoperative or Continuous Illumination

If the switch is malfunctioning the cruise control will not engage.

Sep 03, 2009 | 2005 GMC Canyon

1 Answer

2004 KIA Optima


Check the fuses for these items they could be blown.

Dec 13, 2008 | 2004 Kia Optima

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

65 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...