Question about Cars & Trucks

Open Question

What is the purpose of the cam-shaft sensor in the 2003 jeep grand cherokee

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Mikey108
  • 475 Answers

SOURCE: 1993 jeep grand cherokee

Try replacing the crank sensor on the transmission bell housing

Posted on Oct 03, 2008

  • 32 Answers

SOURCE: need to replace crank sensor on 2003 jeep grand cherokee

its easy, its underneath the passenger side located halfway up the transmission bell housing unplug, u will need to use a 1/4inch drive ratchet and socket to loosen the bolt and simply remove and reinstall with the new one

Posted on Oct 05, 2009

  • 1 Answer

SOURCE: 2002 Jeep Grand Cherokee 4.0L 6 cyl camshaft position sensor

TRANSMISSION SENSOR FOR A GRAND CHEORKEE 2002

Posted on Jan 17, 2010

  • 46 Answers

SOURCE: Front drive shaft on Jeep Grand Cherokee

yes but make sure you don't in gauge the front axle

Posted on May 19, 2010

emissionwiz
  • 75797 Answers

SOURCE: location of cam sensor 2003 jeep grand cherokee v8

Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Posted on Jul 21, 2010

Testimonial: "that is just what i needed thanks"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Jeep grand cherokee dies while driving


did you change the fuel filter, very common problem that gets over looked too many times

Nov 25, 2013 | 1999 Jeep Grand Cherokee

1 Answer

Engine light came on...reading states its my cam shaft sensor, but dealer states 1997 grand cherokees 6 cyl. dont have a cam shaft sensor...What can it be then? if reading staes its a cam shaft?


Your cam sensor is inside the distributor. Problem is they list it as a Stator, not a sensor. on newer models, the sensor replaces the entire distributor. To remove it, you need to take the distributor out of the engine and remove the center shaft etc.

Apr 12, 2011 | 1997 Jeep Grand Cherokee

2 Answers

01 Jeep grand cherokee laredo won't start. No fire is going to engine. Changed spark plugs but didn't help at all


you might want to check you cam shaft sensor amd also there is a different sensor under the distutor i had to replace both of these on my 95 jeep grand cherokee laredo

Dec 04, 2010 | 2001 Jeep Grand Cherokee

1 Answer

Location of cam sensor 2003 jeep grand cherokee v8


Answer
pic_12.gif
pic
REMOVAL - 4.7L
The Camshaft Position Sensor (CMP) on the 4.7L V–8 engine is bolted to the front/top of the right cylinder head (CMP Location—4.7L Engine).

It is easier to remove/install sensor from under vehicle.

Raise and support vehicle.
Disconnect electrical connector at CMP sensor (CMP Location—4.7L Engine).
Remove sensor mounting bolt (CMP Location—4.7L Engine).
Carefully twist sensor from cylinder head.
Check condition of sensor o-ring.
See picture for sensor location.


9347d80.gif

Jul 21, 2010 | 2003 Jeep Grand Cherokee

2 Answers

93' Grand Cherokee, dont start, no spark,no gas preassure


my 1996 jeep grand cherokee lmtd. won't start did tune up. cranks but no fire. please help. engine code 54 shows up . cam shaft positioning no signal. . tested all circuit. changed cam shaft positioning sensor twice.still cranks did start once ran for 5 min. changed the sensor again. no luck. help please. keith

Sep 10, 2009 | 1993 Jeep Grand Cherokee

3 Answers

1996 jeep grand chrokee turns over will not start, replaced cam shaft censor and ECM, and coil. distibuter cap looks bad has some white dust inside and contacts burnt. could it be that?


If you did not replace the CRANK sensor on the back side of the motor this most likely is the problem and a very common one at that.this controls spark and injector pulse,unlike the cam sensor which just shows when #1 cilyder is up.

Jul 03, 2009 | 1996 Jeep Grand Cherokee

1 Answer

2003 Grand Cherokee Laredo turns off when put on reverse.


Throttle Possition Sensor is the usual issue for your concern

Jun 30, 2009 | 2003 Jeep Grand Cherokee

1 Answer

1993 jeep grand cherokee


Try replacing the crank sensor on the transmission bell housing

Sep 28, 2008 | 1993 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...