a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need. Goodluck!
Take off the panel with the sunroof button on it there should be a hex wrench in there, there is also a hex fitting, turn this to maually close the sunroof. If the hex wrench is missing you can use any hex wrench that will fit.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Sunroof Description and Operation (One Connector System)
This diagnostic procedure is to be used for the 1 connector Sunroof System that combines the sunroof control module with the sunroof motor/actuator.
The Sunroof System consists of the following components:
• BATT MAIN 2 Fuse 50 A
• Body control module (BCM)
• RAP relay
• S/Roof Fuse 20 A
• Sunroof module (includes sunroof motor/actuator)
• Sunroof switch
The Sunroof System is controlled by the sunroof switch and the sunroof motor/actuator assembly.
When the ignition is turned to RUN or ACCESSORY, or when the retained accessory power (RAP) system is active, the body control module (BCM) applies a ground to the RAP relay in the instrument panel (I/P) fuse block. This activates the RAP relay and allows battery positive voltage to be applied through the SUNROOF Fuse to the sunroof module. Ground for the sunroof module is supplied from G302.
The sunroof can be placed in 3 preset positions:
When the sunroof switch is placed in the OPEN position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof motor/actuator then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the full open position.
When the sunroof switch is placed in the VENT position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch open signal circuit. The sunroof module then applies voltage to the sunroof motor open control circuit and applies a ground to the sunroof motor close circuit. The sunroof motor then opens the sunroof to the VENT position.
When the sunroof switch is placed and held in the CLOSED position, a ground is applied from the sunroof switch low reference circuit , through the sunroof switch and to the sunroof switch close signal circuit. The sunroof module then applies voltage to the sunroof motor close control circuit and applies a ground to the sunroof motor open circuit. The sunroof motor then closes the sunroof.
The sunroof can be placed in any preferred open position when:
• The sunroof is in the fully opened position by pressing and holding the sunroof switch in the CLOSE position until the panel has reached the desired position then release the CLOSE switch in order to stop the sunroof
• The sunroof is opening, it can be stopped by momentarily pressing either side of the switch.
The sunroof control module, sun roof actuator, and the sunroof motor are integral parts of the sunroof module assembly and are not service separately.
Your best bet , take it to a qualified repair shop or buick dealer .
you may have to strip out the roof lining to gain access to the sunroof component if you cant pull the sun visor free , dont keep pressing the power button as could at the least blow the fuse , at worst burn out the motor
HAVE SAME PROBLEM ON MY ALERO , WOULD CLOSE TO VENT POSITION ALL OTHER FUNCTIONS WORKED FINE. TALKED TO A MECH. FRIEND AND FOUND A WAY TO CLOSE MANUALLY BUT YOU DO HAVE TO DROP FRONT LEFT CORNER OF HEADLINER. THE MOTOR IS UNDER SUNVISOR AREA AND YOU'LL NEED AN ALLEN(SPELLING)SOCKET TO CLOSE ROOF
I think I know the answer....your gear has slipped on the cable a few teeth. Set the roof to the desired closed position, flush with your roof. Then open the panel above the mirror by first prying off the switch plate and removing the two 10mm bolts holding the mirror. Remove the sunroof motor gear, or rather just lower it out so it is disengaged with the cables. Now connect the switch and hit the auto open button as if you wanted to open the roof with single flick of the switch. Now hit the auto close button (same button of course, but the single touch method). The motor will advance and stop to where it thinks the roof should be, closed, which it is. Reassemble the gear into the slot, test it if all good, replace the mirror and panel.
It sounds like it just needs to be reinitialized. Turn your key to the on position with motor off and hold the up/full vent button down for at least 30 seconds or until your sunroof either clicks or goes to the full vent position. That should fix your problem.
you can open and close you sunroof "manually" remove the plastic cover next to your sunroof and dome light buttons (above your rearview mirror) there is an allen wrench stored inside... insert the wrench into the corresponding hole and you can close or open you sunroof by turning the wrench
a solution that i had is that if you can open your sunroof without it opening ur shade try that then fold the shade by pushing between or in the middle of it and popout the shade. this works but try not to push to hard or you can break the plastic runners on the side of the shade. check to see if nothing is in the way of the runners. then put back the back part first then slide it all the way to the back then, do the other part and clip them back together
(there might be a little metal piece that pushes your shades back so check that first to see if its there first)
tilt the sunroof into vent position as far as possible then press and hold the same switch for 30 seconds until you see it move release the switch and immediately press and hold it again the sunroof will close and open fully then close again do not release the button until it reaches the closed position for the second time.