Question about 1995 Ford Explorer 4.0

1 Answer

Relay fuse,where?and reset

Don't know where fuel pump relay or know which one it is,and where is the reset switch located

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 7 Answers

The fuel pump relay is #7 and if your talkin about the intretia switch reset the switch is in the passangers floorboard may be tucked just under carpet

Posted on Jan 06, 2014

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

SOURCE: i need a 2002 ford ranger fuse box diagram and afuel pump relay switch diagram

Hi

go to www.motorcraftservice.com then click on the owner guide and put in your truck information
then choose the 1st owner manual printing and should be between page # 184 to 200.

Good luck and I hope this will awnser your question.

Posted on Nov 08, 2008

  • 491 Answers

SOURCE: 1988 ford f150 fuel pump relay location

inner driver side fender well along with the eec relay

Posted on Feb 02, 2009

michigan man
  • 3533 Answers

SOURCE: 92 mustang reset switch electric fuel pump where located

on the mustangs i have the switch in just inside the rear hatch on the right side a yellow button you may have to remove a small cover to see it

Posted on Apr 27, 2009

wyatt1582
  • 453 Answers

SOURCE: 99 ford mustang gt, won't start not getting fuel

Fuel reset is in the trunk look in the trunk along the side for a hole you will see a with button push down. To check relay just turn your key forward and lsiten for a click sound thats the easiest and fastiest way to check it. (Fuel pump relay should be located under the hood in the engine compartment.)

Posted on May 21, 2009

sscullys
  • 984 Answers

SOURCE: can anyone tell me the location of the fuel pump

The Fuel pump relay is a non serviceable relay ( built into the fuse panel ) in the 04-08 MY F-150s.

Did you check the Fuel Inertia switch ( in the passenger side kick panel by the fuse panel ) ?

If you are having a no fuel pressure issue, might want to take a look at the FPDM ( Fuel Pump Driver Module ) on the cross member above the spre tire ( need to drop the spare to see if ).

There is an issue with 04-07 ( 04-06 ?? ) MY trucks where the FPDM is bolted directly to the cross member, and dissimilar metal corrosion happens and builds up behind the FPDM, causing it to break.

Here are some before and after pictures from my 2006, I replaced mine for the heck of it and found that the case had cracked with ~ 51K miles on it, soon the PCB would have cracked leaving me stranded

d416568.jpg

d3de10c.jpg

New version of the FPDM with the stand off studs
4b54e66.jpg

This is the kit I got ( check that the Part Number has not been changed )
3dc6520.jpg

Posted on Jun 28, 2010

Testimonial: "thanks for the tip i'll check it out. i've tried to reset the fuel cut-out but it's hard to tell if it resets and finding a test point to prove it is well.... daunting. i have no fuel pressure whatsoever and the fuel pump will not run although it will if i put 12v directly to the fuel pump motor so i know it's not the fuel pump."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1989 f-250 inertia fuel shut-off switch switch location


This should be in the owner's manual. I found the below on autozone.com, their repair help location:
An inertia switch is used as a safety device in the fuel system. The inertia switch is located in the cab, generally under the dashboard on the right side. It is designed to open the fuel pump power circuit in the event of a collision. The switch is reset by pushing each of 2 buttons on the switch simultaneously (some models use switches with only one reset button). The inertia switch should not be reset until the fuel system has been inspected for damage or leaks.
When the ignition switch is ON , it turns the EEC power relay ON . The EEC power relay provides power to the powertrain control module (PCM) and the control side of the fuel pump relay. Power for the fuel pump(s) is supplied through a fuse link or high current fuse attached to the starter solenoid (battery side). From the fuse link or high current fuse, current flows through the fuel pump relay and inertia switch to the fuel pump(s). The fuel pump relay is controlled by the PCM.
When the ignition switch is turned ON , the fuel pump(s) will operate. If the ignition switch is not turned to the START position the PCM will shut the fuel pump(s) OFF after 1 second. The PCM will operate the fuel pump(s) operate the fuel pump(s) when the ignition switch is turn to START position to provide fuel while cranking.
After the engine starts, the PCM will continue to operate the fuel pump(s) unless the engine stops, drops below 120 rpm or the inertia switch is tripped.

Dec 28, 2013 | 1989 Ford F 250

1 Answer

Fuel pump won't run unless engine is cranking, but won't start


Are you sure it's running when cranking? It should have come on when key turned on.
This is for camrys up to year '91. It may apply in your '95, also. Check the 7.5 amp ignition fuse and the 15 amp EFI fuse and the EFI main relay, all located in the fuse box next to your battery. There is also the circuit opening relay tied in to fuel pump operation. It is usually found under center of dash. It is usually not the problem, but it is part of the checks for fuel pump operation.
If your car has a " check connector" or "service connector" (also called a fuel pump check connector) under hood on driver's side near the firewall (a little 1 inch cube with a cap on it), then bridge terminals +B and Fp with a jumper wire. Turn key to on (don't start car). The pump should come on. Listen for fuel return noise from the fuel pressure regulator, and verify pressure in hose from the fuel filter. If nothing, check those fuses above. Here is how power runs to pump: Battery to 40 amp main fusible link-to 15 amp EFI fuse-to EFI main relay-to circuit opening relay-to fuel pump-to ground. Ignition switch and the computer (ECU) work the relays to pass power to pump. Hope this helps some, Randy. Good luck.

Nov 10, 2011 | 1995 Toyota Camry

2 Answers

Where is fuel pump relay is location on Ford expedition 2001 4.6


It is located in the relay and Maxi fuse box under the hood near the battery, both the fuel pump fuse and relay are in this box, the fuel pump fuse is a 20Amp and is marked #10, the fuel pump relay is is marked as relay #301.

There is also a fuel pump cutoff switch (triggered by an accident exceeding 3 G's)

The fuel pump shut-off switch is

located in the passenger's foot well,
by the kick panel.

Jul 19, 2011 | 2001 Ford Expedition

1 Answer

Car will turn over but won't start. Through the


No noise from fuel pump when you turn over the car .First thing get voltage at fuel pump relay checked, is there 12 volt to the relay.If no, then problem is again the relay.--------- To reconfirm the problem, try other test, that is remove the relay and by pass the relay terminals with a jumper wire .Then with 12 volt external battery give power to fuel pump connector and see, if the fuel pump starts, then its clear that fuel pump relay is faulty.----------- Also other problem can be fuel pump inertia switch.If the inertia switch is faulty then also fuel pump will not start.-------- The fuel pump relay on a 1995 Ford Explorer is in the power distribution
box, in the engine compartment, driver's side near the firewall.----------
The fuel pump inertia switch is in the right front passenger area
it is below the dash but above the carpet in the right hand corner.--------
Its a push button type inertia switch.
--------
Fuel Pump Activation
When ignition switch is turned to START position, PCM operates fuel pump relay to provide fuel for starting engine. PCM senses engine speed and shuts off fuel pump by opening ground circuit to fuel pump relay when engine stops or engine speed drops to less than 120 RPM. When ignition switch is in ON position, EEC power relay is energized (contacts closed). Power is provided to fuel pump relay and timer in PCM. Fuel pump receives power through fuel pump relay contacts.
Inertia Fuel Shutoff (IFS) Switch
All models use an electrical interrupt switch in fuel system. During a collision or vehicle rollover, electrical contacts within inertia switch open, shutting off fuel supply to electric fuel pump. Fuel supply is interrupted even when engine is running.
A reset button is located on switch assembly. If electrical circuit trips, vehicle will not restart until switch is reset. Fuel system should be inspected before resetting switch.
IFS switch is located under instrument panel, near right side of transmission hump.
----------- If the fuel pump relay, the inertia switch and fuel pump all checked ok, and fuel pump is working with direct 12 volt source to fuel pump.Then problem relates to computer.The computer (power control module, PCM) is faulty and has to be replaced.--------- This will help.Thanks.Helpmech.

Jul 17, 2011 | 1995 Ford Explorer

2 Answers

The gas pump was replace on my 1999 ford expedition but still is not working


There are a few things you can check. The first thing and most likely what the problem is would be the fuel cut off switch. Below is a picture of it the location of it. Where you see the blue arrow pointing down is where the button is that you push to reset it if it is "popped". If that is good the next thing you can check is the fuse for the fuel pump. That fuse is located in the power distribution box located in the engine compartment under the hood (picture of that location below as well) I also gave you a diagram of the layout of the fuses with numbers. The fuse for the fuel pump is the fuse located in the number 10 position and should be a 20 amp fuse. Last you may need to check the fuel pump relay. That relay is located in the same fuse panel and will be the one marked number 301. I hope this helps and good luck.


clifford224_888.gif


clifford224_889.gif


clifford224_890.gif

Jun 23, 2011 | 1999 Ford Expedition

2 Answers

I replace the fuel pump on my 1992 ford bronco and still doesnt supply fuel is there a relay i dont know of


Are you getting battery power and ground at the fuel pump connector? (This should have been checked BEFORE replacing the pump)

Other things to check:
1. Fuel Pump relay in the Engine Compartment Fuse Block
2. The relay is powered (Secondary -or- "fuel pump side") by Fuse 0 in the Engine Compartment Fuse Block.
3. The relay Primary -or- "control" side is powered by Pin 37 RED wire at the PCM
4. The relay Primary control (or ground circuit) is operated by Pin 22 LIGHT BLUE/ORANGE wire at the PCM
5. The Inertia Fuel Shut-off Switch located between the fuel pump relay and the fuel pump may need to be reset. The switch is located behind the right kick panel. The DARK GREEN/YELLOW wire at the switch is the feed from the fuel pump relay. The other wire goes to the fuel pump. Some units have the DARK GREEN/YELLOW wire going in and the wire going out can also be DARK GREEN/YELLOW, or PINK, or ORANGE - the wiring diagram for your vehicle does not specify the color of the wire that actually goes to the fuel pump itself.)
6. If none of the above produce any results, make sure that your ground wire at the fuel pump has good continuity to ground. It usually screws to the left frame rail near the fuel tank.

Any of these components (including the PCM) or their connecting wires could be the cause of your problem.

May 15, 2011 | 1992 Ford Bronco

2 Answers

I need to know where the fuel pump relay is, or where the fuel pump reset button is


See picture below where the fuel pump cut off switch is located. The fuel pump relay is located in the power distribution box located in the engine compartment (see other picture). The relay is located in the R7 position in that box (see layout diagrams below). There is also a fuse for the fuel pump which is located in the same fuse panel. That fuse is in the nuber 12 position and should be a 15 amp fuse. All of this should be in your owners manual if you have one. If you don't and would like a copy, you can email me at csautomotivecars@att.net with your make, model and year and I will be happy to email you a copy. I hope this helps and good luck.


clifford224_449.gifclifford224_450.gifclifford224_451.gifclifford224_452.gif

May 11, 2011 | 2000 Ford Focus

1 Answer

Fuel pump trouble shooting, Iv'e replaced the relay and don't get a reading on my VOM with the ingition on and the probes on the pump power and ground. Didn't get a reading with the old relay...


The fuel doesn't receive power unless the engine is being cranked or it is running, did you know this? The only fuse is under the hood and marked.

May 10, 2011 | GMC Sonoma Cars & Trucks

2 Answers

Where is the fuse for a 2001 ford 4.6litre mustang(fuel fuse)


The fuse for the fuel pump is located in the power distribution box/fuse box located in the engine compartment. It is in the number 14 position and should be a 20 amp fuse (see picture below of the fuse layout). Also, I don't know if you have checked this or not but there is a fuel pump cut off switch located in the trunk of the vehicle. I gave you a picture of its location in the second picture below. This should all be in your owners manual if you have one. If you do not and would like a copy, you can email me at csautomotivecars@att.net with your make, model and year and I will be happy to email you a copy. I hope this helps you and good luck.


clifford224_248.gifclifford224_249.gif

Apr 24, 2011 | 2001 Ford Mustang

3 Answers

No power to fuel pump on 1999 crown victoria


Hello abzalkhan193
Heres a few things to check that could cut power to the fuel pump. The fuel pump inertia shutoff sw
in the trunk on the left side, there is a reset button on the switch if you push the button down and
you hear/feel a click then the switch was tripped and you just reset it. The switch's job is to cut off
the fuel in case of an accident. Next, the fuel pump fuse located in the battery fuse block under the
hood on the right fender well, fuse #1 20amp fuse. Next, the fuel pump relay, the relay is located in
relay center on the left fender well. Hope this is helpful.

Mar 11, 2011 | 2001 Ford Crown Victoria

Not finding what you are looking for?
1995 Ford Explorer 4.0 Logo

129 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

fordexpert

Level 3 Expert

5520 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...