Question about BMW Cars & Trucks

Open Question

Cylinder head bolt torque for BMW n46 engine

Cylinder head bolt torque for BMW 316ti , 2004 year

Posted by Anonymous on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

Ad
  • 20 Answers

SOURCE: 2004 chevy aveo cylinder head bolt torque how many

Step 1: 18 lb.-ft.
Step 2: additional 60 degrees.
Step 3: additional 60 degrees.
Step 4: additional 60 degrees.
Step 5: additional 10 degrees.

Each step involves starting at the center two bolts of the head and alternately tightening in a criss-cross pattern, ending with the bolts on the outer edge of the head.

Posted on Sep 14, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

  • 1 Answer

SOURCE: torque setting cylinder head bolt 4 cylinder KIA sportage

I need the torque settings and pattern for a Kia Sportage 2.2

Posted on Jan 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2001 buick century torque prints for haeds on up


the 3100 specs
Type: Bolt Dim: Length: Head: Hexagon Grade: 37 Ft-Lbs 444 In-Lbs 50.17 N-m Connects: Cylinder Head To Engine Block Years: 1998-2001 Vote Record: Vote Note: 3100 - Head Bolts - 2 Steps: 37FtLbs; +90deg
12 Ft-Lbs 144 In-Lbs 16.27 N-m Connects: Exhaust Manifold To Cylinder Head Years: All Vote Record: Vote Note: 3100 - Exhaust Manifold to Cylinder Head
Type: Bolt Dim: Length: Head: Hexagon Grade: 9.58 Ft-Lbs 115 In-Lbs 13 N-m Connects: Intake Manifold To Cylinder Head Years: All Vote Record: 0/1(0%) Note: 3100 - Lower Bolts - 2 Steps: 5 FtLbs; 9.58 FtLbs Here are the head bolt torques for a 3.8
37 Ft-Lbs 444 In-Lbs 50.17 N-m Connects: Cylinder Head To Engine Block Years: 1999-2005 Vote Record: Vote Note: 3800 II - 2 Steps: 37FtLbs; +120deg
13 Ft-Lbs 156 In-Lbs 17.63 N-m Connects: Exhaust Manifold To Cylinder Head Years: 1999-2005 Vote Record: Vote Note: 3800 II - Exhaust Manifold to Cylinder Head - NOT FRONT 2
7.42 Ft-Lbs 89 In-Lbs 10.06 N-m Connects: Fuel Rail To Intake Manifold Years: All Vote Record: Vote Note: 3800 II - Fuel Rail Mounting Bolts 2.25 Ft-Lbs 27 In-Lbs 3.05 N-m Connects: Idle Air Control Valve To Throttle Body Years: All Vote Record: Vote Note: 3800 II - Idle Air Control Valve to Throttle Body Type: Bolt Dim: Length: Head: Nut Grade: 11 Ft-Lbs 132 In-Lbs 14.92 N-m Connects: Intake Manifold To Cylinder Head Years: All Vote Record: Vote Note: 3800 II - Intake Manifold to Cylinder Head Bolts/Nuts
7.42 Ft-Lbs 89 In-Lbs 10.06 N-m Connects: Intake Manifold Plenum To Intake Manifold Years: All Vote Record: Vote Note: 3800 II - Intake Manifold (Upper) to Lower Manifold Type: Bolt Dim: Length: Head: Hexagon Grade: 14 Ft-Lbs 168 In-Lbs 18.98 N-m Connects: Knock Sensor To Cylinder Head Years: All Vote Record: Vote Note: 3800 II - Knock Sensor

Jul 24, 2016 | 2001 Buick Century

2 Answers

Head bolt torque spec 05 bmw 4.4l


  1. Cylinder Head - AutoZone

    www.autozone.com/.../BMW-X5...05/.../Cylinder-Head/_/P-09...

    AutoZoneBMW X5 2000-05 .... Cylinder head bolt tightening sequence-4.4L & 4.6L engines. To install: ... Torque the bolts in thesequence illustrated in 3 steps as follows:.

Oct 17, 2014 | Cars & Trucks

1 Answer

Head bolt torque spec 05 bmw x5 4.4l


  1. Cylinder Head - AutoZone

    www.autozone.com/.../BMW-X5...05/.../Cylinder-Head/_/P-09...

    AutoZoneBMW X5 2000-05 .... Cylinder head bolt tightening sequence-4.4L & 4.6L engines. To install: ... Torque the bolts in thesequence illustrated in 3 steps as follows:.

Oct 17, 2014 | Cars & Trucks

1 Answer

Correct pressure for torque the head of mazda pickup 1998


Since you didn't say which engine you have, I've pulled torque specs for 3 different engines. Also, since I can't include a diagram showing the relative locations of the numbered head-bolt locations, it would be a good idea for you to purchase a vehicle specific repair guide that will show this info.


Take particular note about the TTY (Torque to Yield) bolts used on 2 of the 3 engines shown. It is said that new head bolts MUST BE USED when head is replaced or re-installed to obtain the proper torque.



B2500 4 Cylinder

Torque sequence: --------- ' 10 6 2 4 8 ' front ' ' ' 7 3 1 5 9 ' -----------Step 1: torque in sequence to 51 Ft/Lbs Step 2: torque again in sequence to 51 Ft/Lbs Step 3: final tighten all bolts an additional 90 to 100 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.







B3000 3.0 6 Cylinder

Torque sequence ---------- ' 6 4 2 8 ' ' ' ' 5 1 3 7 ' ---------- Step 1: torque to 59 Ft/Lbs Step 2: loosen in sequence (1) full turn Step 3: torque to 41 Ft/Lbs Step 4: torque to 73 Ft/Lbs









B4000 4.0 6 Cylinder

Torque sequence --------- ' 5 1 3 7 ' ' ' ' 6 4 2 8 ' --------- Step 1: torque cylinder head bolts in sequence to 26 Ft/Lbs Step 2: torque cylinder head bolts to 56 Ft/Lbs Step 3: turn cylinder head bolts in sequence an additional 90-degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) that permanently stretch during the initial installation. New head bolts must be used when cylinder head is replaced or re-installed to obtain proper torque.


Good luck with this job!

Feb 06, 2011 | 1998 Mazda Pickup

1 Answer

Need cylinder head torque specifications 2004 hyundai elantra


Install the cylinder head bolts. Starting at top center, tighten all cylinder head bolts in sequence as shown in illustration, using the Cylinder Head Bolt Wrench (09221 - 32001) or equivalent. Repeat the procedure, re-tightening all cylinder head bolt to the specified torque. (torque spec is Cold Engine 105-115 Nm (76-83 ft lb) )
. Install the timing belt tensioner pulley.
. Install the timing belt on the camshaft sprocket, making sure that the tension side is tightened by turning the camshaft sprocket in reverse, all timing marks are in alignment.
. Adjust the timing according to "Timing Belt"
. Install the rocker cover and tighten the bolts to the specified torque. Tightening torque: Rocker cover belt:

2.5-3.5 Nm (25-35 kg.cm, 2-3 ft. lbs.)

. Install the timing belt cover.
Install the new intake manifold gasket and the intake manifold. Tighten the nuts and bolts to the specified torque.
Install the new exhaust manifold gasket and the exhaust manifold. Tighten the exhaust manifold attaching nuts to the specified torque.
. Install the surge tank and tighten the nuts bolts to the specified torque.
. Install the power steering oil pump and bracket.
. Install the ignition coil.
. Install the air intake hose.
Connect the vacuum hose, fuel hose and water hose.
. Install breather hose.

Dec 22, 2010 | 2004 Hyundai Elantra

1 Answer

Looking for head bolt troque spec for 3.4l impala sfi04


Please don't forget to rate. Thank you:

Left side front cylinder head


98e175a.gif
Cylinder head bolt torque sequence-3.4L engine

  • Cylinder head by aligning it with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Left side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).


  • Right side rear cylinder head:


    71cd5b7.gif
    Cylinder head bolt torque sequence-3.4L engine


  • New cylinder head gasket
  • Cylinder head on top of the gasket and make certain it is lined up properly with the dowel pins
  • New cylinder head bolts coated with a sealant (such as GM 1052080). Torque the bolts in the proper sequence (1-8) to 37 ft. lbs. (50 Nm). Using a torque angle meter turn the bolts 90 degrees in the proper sequence.
  • Right side exhaust manifold. Torque the bolts to 12 ft. lbs. (16 Nm).
  • Spark plugs. Torque the plugs 11 ft. lbs. (15 Nm).
  • Spark plug wires
  • Exhaust crossover pipe. Torque the fastener to 18 ft. lbs. (25 Nm).
  • Valve rocker arms and pushrods. Torque the fastener to 89 inch lbs. (10 Nm). Using a torque angle meter torque the fastener an additional 30 degrees.
  • Lower intake manifold. Torque the bolts to 115 inch lbs. (13 Nm).
  • Upper intake manifold. Torque the bolts to 18 ft. lbs. (25 Nm).
  • Nov 26, 2010 | 2004 Chevrolet Impala

    1 Answer

    I need torque specs for the head bolts on a 2004 Dodge Stratus Coupe 2.4L SOHC


    For 2004 Dodge Stratus 2.4L SFI SOHC 4cyl the Head Bolt Torque sequence
    ------------ | 10 6 2 3 7 | | 9 5 1 4 8 | ------------

    Step: 1 - Torque to 25 ft/lbs
    Steps: 2 - Torque to 50 ft/lbs
    Steps: 3 - Torque to 50 ft/lbs
    Steps: 4 - Turn 90 degreesRecheck final torque in sequence

    Caution:Engine uses torque to yield head bolts (TTY) that permanently stretch during initial installation. New head bolts must be used when cylinder headis replaced or re installed to obtain proper torque specification.

    Hope helps (remember comment and rated this).

    Aug 02, 2010 | 2004 Dodge Stratus

    1 Answer

    I need to find the torque specs for the connecting piston rod? also the sequence and torque for the cylinder head bolts this is for a kia rio 2004 6cyl


    22 - 24 ft. lbs. for the rod caps and....
    110795143Cylinder Head Tightening Torque and Sequence.

    Tighten cylinder head bolts in order shown.
    Tightening torque: 36.1 ft. lbs. (49 Nm, 5 kg-m)

    Loosen bolts in reverse of order shown.

    Retighten cylinder head bolts in order shown.
    Tightening torque: 18 ft. lbs. (25 Nm, 2.5 kg-m)

    Mark cylinder head bolts for rotational reference.
    Rotate cylinder head bolts 90°(1/4 Turn) in order shown.

    CAUTION:
    • Do not reuse the old cylinder head bolts.

    May 31, 2010 | 2004 Kia Rio

    1 Answer

    Head bolt touqe settings


    Tightening torques

    Do not reuse the bolts as they may be stretched.

    Cylinder head to engine block
    Stage 1: 32Ft-lbs
    Stage 2: +90degrees
    Stage 3: +90degrees

    Cylinder head to lower timing
    chain cover: 89in-lbs

    Nov 27, 2008 | 1992 BMW 3 Series

    3 Answers

    Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36


    BMW cylinder torque setting all models

    According to my service manual as follows.

    Cyl head to engine block (torx e12 M10 bolts)

    Stage 1 30nm (22 ft – lb)
    Stage 2 + 90 degrees
    Stage 3 + 90 degrees

    Cyl head to lower timing chain cover 10nm (89in – lb)

    The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

    Jun 16, 2008 | 1992 BMW 3 Series

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    440 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top BMW Experts

    Frankie B

    Level 2 Expert

    65 Answers

    Fred Sops

    Level 2 Expert

    272 Answers

    Doberman

    Level 2 Expert

    254 Answers

    Are you a BMW Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...