Question about Cars & Trucks

Open Question

Coats 4040A When the foot pedal is depressed to break the bead the bead breakers cycle and the center rotates as it should. However when the foot pedal is released the bead breaker remains locked down in the bead break position and won't release. The only way to get it to release and return to the home position is to push both pedals down at the same time activating the bead inflation jets to release a sufficient amount of air which allows the machine to return to it's home position. I suspect a bad valve but don't want to just start changing parts. Any help would be appreciated.

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 916 Answers

SOURCE: hard to shift into park.depressing brake pedal does not release

the brake switch may be failing, causing the gears to stay in a locked position making it hard to shift into park

Posted on Dec 27, 2008

  • 73 Answers

SOURCE: emergency brake foot pedal not working

Sounds like the cable is stuck also check the catch on the foot pedel

Posted on Mar 13, 2009

alicantecoli
  • 22114 Answers

SOURCE: emergency brake locked after pull release handle

handbrake jammed on somewhere ,could be front cable ,because the rear cable is pulled by the compensator so if it was the rear one then i would expect only one cable siezed and that is normally the kerbside one.

Posted on Oct 23, 2009

  • 11800 Answers

SOURCE: I have a 1999 (actually

The clutch works this way: press the pedal, the pedal pulls a cable, that cable moves a lever with a bearing at its end, that bearing presses on the extremities of the disk spring, that spring deforms and lifts the pressure plate disengaging the clutch plate.
In your case the spring is no longer doing disengaging because either the bearing or the extremities of the disk spring have failed - most likely the latter. You will gonna have to replace the pressure plate assembly.
Here's a complete clutch kit
http://www.partsgeek.com/catalog/1998/volkswagen/cabrio/clutch/clutch_kit.html

Posted on Oct 11, 2010

  • 1243 Answers

SOURCE: shift lever lock won't release when brake pedal is

do the brake lights work? most of the time the problem is a broken wire at the brake light switch under the dash on the brake pedal. the ECM does not see the signal from the switch so it won't allow the car to shift from park.

Posted on Jul 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I hear a cclicking noise when I step on break when key is on. I don't hear the click while car is running. Its a 97 infinity q45


Most automatics have a lock on the transmission selector.
When the vehicle is in P (Park) you are not able to select drive or a gear unless you depress the brake pedal.
My Audi Q7 ha a solenoid and you hear it click when I put my foot on the brake.
This solenoid stops you from accidentally selecting a gear without the brake depressed.

Is it a single click when you depress the pedal.
Or is it a constant click click click ?

Apr 28, 2015 | Infiniti Q45 Cars & Trucks

1 Answer

High pitched squeal when jeep idles or during deceleration. soonafter, clutch pedal jumped violently under my foot followed by engine stalling out. could not depress clutch pedal after that.


It sounds like your clutch bearing has gone they are usually on a pendulum system it screeches before it starts to go. Best get it checked.

Apr 15, 2014 | 1995 Jeep Wrangler

1 Answer

Tail light wire


Adjust the brake pedal switch located on the upper side of the brake pedal under the dash. To adjust the stop light switch, disconnect the two wires attached to the rear of the switch, move the switch by loosening the lock nut towards the brake pedal. As soon as the center pin of the switch begins to touch the brake pedal notch, rotate the switch half turn more and lock it by tightening the lock nut. Connect the wires back and ask your companion to see the tail lamps while you depress and release the brake pedal. Or you can see the tail lamp behavior by parking the car on reverse at a distance of one foot from any wall.

Nov 30, 2013 | Toyota Previa Cars & Trucks

1 Answer

Stop lights is on every time


If your stop lights are on all the time, your stop light switch, mounted on the steering coluum under the dash, is either defective or out of adjustment. Make sure the switch is depressing when foot is off the break pedal. If it is, then the break switch is defective. Good luck!

May 01, 2010 | 1999 Ford Expedition

2 Answers

Parking break


One or both of your rear emergency brake cables are/is frozen. Give them both a good soaking with nothing but PB blaster. make sure you get the entire sheilded area. You may at the same time want to adjust up the rear brakes. Now back to that pedal. Have someone under the drivwers side pull hard on the E-bracke center cable while you depress and release the foot pedal. don't do this until the cables have set all night with the spray on them. Good Luck! Thanks, Dana

Aug 17, 2009 | 1996 Dodge Grand Caravan

2 Answers

Gear shift won't move out of park


safety switch on brake pedal. common cause is a wire breaking off. there are 1 to 2 wires going to this switch. It is located on the brake pedal bracket above the foot pad.

Jul 19, 2009 | 2003 Volkswagen Jetta TDI

1 Answer

1995 volkswagon passat starts while in gear.






Since you have already tried the obvious look to make sure that the new switch is properly engaging when you move the pedal. Most of these switches have some adjustment in their placement. Otherwise search through the wire harness and tape up ANY cracks or breaks in the plastic coating. Also look at all the connectors for green corrosion. If you find or suspect corrosion replace the connector. VW''s are picky when it comes to corrosion and breaks in wire insulation. Hope this helps.














Jun 04, 2009 | 1995 Volkswagen Passat

2 Answers

Brake lights


brake switch........ or fuse to the switch

Oct 19, 2008 | 2002 Oldsmobile Bravada

1 Answer

Break light problem


Do you know if the brake light bulbs are working? (are the bulbs good?). (the bulbs have two parts, one for brake lights the other for running lights)
If the third brake light bulb is working the brake lights should be with good light bulbs.

Jul 22, 2008 | 2005 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...