Question about 2002 Hyundai Santa Fe

Open Question

Location oil sensor 2.7 v6 - 2002 Hyundai Santa Fe

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can you tell me where the knock sensor is located on a 1998 toyota tacoma


depends on engine - dealer will tell u by serial #1.
help on net. however one is located left [to firewall from oil filter.
# 2 could be drivers side under intake manifold in the valley.
So unless want a big job look near the oil filter. oil dender is ahead of the filter..on the block.. But as I sead ask the parts department at a dealer..Good luck.. I had the wire drop off on my 89 3 liter v6 .was of roading just by the oil filter.. stick I guess.
cowcamp

Sep 20, 2014 | 1998 Toyota Tacoma

1 Answer

Where is the oil pressure sensor located on a 2004 Ford Escape 3.0L/V6


I dont have the image of the sensor but normally its located near the oil filter with a single wire on it... sometimes the location has an easy access but most of the time its not so goodluck

Aug 15, 2014 | Cars & Trucks

1 Answer

Bank 2 sensor 1 is bad, where is it located on my 05 accord v6 coupe?


If this is a V6 bank 2 sensor is the one before the catalytic converter in the bank of cylinders that contains cylinders 2,4 and 6.

Aug 28, 2012 | 2005 Honda Accord

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

1 Answer

Oil filter location


The V6 has a screw on filter unlike the 4 cylinder which has a cartridge filter. The filter is located in one of 2 positions depending on which V6 you have. On one V6 it is located under the car towards the front where there is a splash guard that is held in place by two thumb screws. Remove the thumb screws take out the splash guard and there it is. On the other V6 it is located under the air tube that comes from the air filter where you will see a nut about the size 3/4 or bigger just unscrew it and change your oil filter.

May 01, 2010 | 2002 Pontiac Grand Am

1 Answer

Oil sending unit on 2004 chrysler sebring V6


Should be located close to the oil filter. It will screw in like a spark plug. It has a harness plug. Easy to change, save yourself $70 in labor. You will need a fairly large wrench to remove

Jan 03, 2010 | 2004 Chrysler Sebring

3 Answers

Locate crankshaft sensor


located by crank pulley in front of motor

Jan 24, 2009 | 2005 Chevrolet Malibu

1 Answer

2006 Toyota Tacoma V6 engine oil sensor location


There is not enough flow at the sensor for a second oil filter. The sensor is at a dead end in the oil gallery. I recommend that you persue other options here. If you are concerned about oil contamination, don't be. There is nothing better than the factory filter...Look into adding more oil capacity; Look into an engine oil cooler; there is really no need for a second filter.

Sep 07, 2008 | 2006 Toyota Tacoma

Not finding what you are looking for?
2002 Hyundai Santa Fe Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...