Question about 2006 Mitsubishi Outlander

Open Question

Fuel door clip

The clip broke on my fuel door & I ordered a new part but am having trouble installing it. Not sure if there's another part I'm missing.

Posted by on

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 333 Answers

SOURCE: how to install mitsubishi lancer fuel door clip

In the center of the hinge area there is a small raised area with a circle hole drilled in it.
The spring slides onto this are, black coated portion facing away from the door; The metal uncoated portion of the clip has a raised circular nub that clicks into the hole on the hinge.
Here is a picture, not a very good one, but it shows you the area I speak of.
Once you see the hole and the nub ont he spring, you'll see there is only one way it will go on.
6026267.jpg

Posted on Oct 30, 2009

Ad
buffalonyman
  • 1865 Answers

SOURCE: I put gas in my 2008 Outlander and a clip dropped out

It should be covered under warranty, take it to the dealer, let them fix it

Posted on Oct 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 96 toyota corolla and can't get the fuel door open


This is usually because the spring the pops it open is broken, have someone pry on the fuel door while ppulling the release inside, the spring clips onto the hinge if it's broken get a replacement from the toyota dealer

Jan 15, 2013 | 2003 Toyota Corolla

1 Answer

Where is the fuel filter location for a 1996 crown victoria


It's front of the driver's rear tire,usually.If not,it'll be on the other side of the car.
Turn off the key and remove.
Open hood and release fuel pressure at the rail with the schrader type valve.
Don't use a bulb type trouble light under there as it can ignite gas easily.
Pry off the old clips after loosening the hold-down clamp. Turn head away as you slide off the hose on the tank side of filter.
Install new filter in holder,attach hoses and install new clips then tighten hold-down clamp. (:^)
don-ohio

Oct 25, 2011 | 1996 Ford Crown Victoria

2 Answers

Instal 1999 ford taurus fuel filter


along the drivers side under the car

Nov 03, 2010 | 1999 Ford Taurus

1 Answer

I have fuel leaking from the fuel rail at the 2nd injector from the front. The leak seems to be coming from where the metal of the fuel rail conects to the plastic....


Maybe an O-ring is leaking. Try a new injector that comes with an o-ring to be sure it's not the injector itself.
Fuel Injector - for V8

REMOVAL & INSTALLATION


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Relieve fuel system pressure.
  3. Remove or disconnect the following:

    • Negative battery cable
    • Fuel rail
    • Fuel injector retaining clips
    • Fuel injectors

    To install:

  4. Install or connect the following:

    • Fuel injectors, using new O-rings
    • Fuel injector clips to the fuel rail
    • Fuel rail
    • Negative battery cable

  5. Start the vehicle and check for leaks, repair if necessary.

Oct 30, 2010 | 2002 Jeep Grand Cherokee

1 Answer

How to change fuel filter mazada 2003 tribute


Mazda Tribute 2001-06
Fuel Filter - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Properly relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Fuel line to the fuel filter
  4. Loosen the clamp and remove the filter
To install:
  1. Install or connect the following:
    New clips to the fuel lines Fuel filter and tighten the clamp Fuel lines to the fuel filter Negative battery cable
  2. Start the vehicle and check for leaks, repair if necessary.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Properly relieve the fuel system pressure.
  3. Disconnect the negative battery cable.
    NOTE To deplete the backup power supply energy, disconnect the negative battery cable and wait at least one minute. Be sure to disconnect auxiliary batteries and power supplies, if equipped.
  4. Disconnect the fuel line at the fuel filter.
  5. Loosen the clamp and remove the filter.
To install:
  1. Install or connect the following:
    New clips to the fuel lines Fuel filter and tighten the clamp Fuel lines to the fuel filter Negative battery cable
  2. Start the engine and check for leaks, repair if necessary.

Hope this help; TY for using Fixya (remember comment and rated this).

Apr 01, 2010 | 2003 Mazda Tribute

3 Answers

How do you change a fuel pump and filter on a 2005 manual chevy aveo?


Removal & Installation
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove the rear seat.
  4. Remove the fuel pump access cover.
  5. Disconnect the electrical connector at the fuel pump assembly.
  6. Disconnect the fuel line.
  7. Remove the fuel pump assembly clip.
  8. Remove the fuel pump assembly from the tank.
  9. Remove and discard the gasket.

To install:
  1. Clean the gasket mating surface on the fuel tank.
  2. Position the new gasket in place.
  3. Install the fuel pump into the fuel tank in the same location as removed for ease of line and connector installation.
  4. Install the fuel pump assembly clip.
  5. Connect the fuel pump assembly connector.
  6. Install the fuel pump line.
  7. Install the fuel pump access cover.
  8. Install the EF10 fuse.
  9. Connect the negative battery cable.
  10. Perform an operational check of the fuel pump.
  11. Install the rear seat.

Mar 06, 2010 | 2005 Chevrolet Aveo

4 Answers

How to replace a fuel pump on jeep wrangler (95)


i'm pretty sure jeep had their pumps in the tank. you can phone parts place to double check. If it is in the tank, you will have to drop the tank in order to access it. Other vehicles have a latch or door thing that will allow you access from the top. pretty sure the jeep does not have this. you will have to disconnect all of the hoses and hopefully your tank is almost empty or else they weigh a ton.....then just take out the old sending unit, put on a new fuel pump and put it back...simplified version, but it will give you a gerneral idea. when i first dropped mine, it took me 1/2 a day, now i can do it in about 1.5-2 hrs

Jul 23, 2009 | 1995 Jeep Wrangler

3 Answers

1997 buick park ave 4 door right front door handle won,t work from the outside


Order the exterior door handle AND the clip that attaches the rod to the exterior handle from your local dealership ( any part in the salvage yard will have at least as much wear as the one U are replacing ) Also order a can of touch up paint matching your car. After you have the parts and have painted the new exterior handle, roll down the window and remove the interior door panel. ( instructions have been posted at 'replace door lock buttom' ) Two nuts, one on each side, hold the broken handle in place and must be removed ( DON'T loose them ). Loosen the rod from the clip at the top to allow a bit more room, But take note on the way it is attached ( you will need to reattach the rod to new handle ) To install new mechanism put the new clip on the rod, carefully place the gasket and the new handle in place and install nuts to secure. Test the door handle and make sure it works. Reinstall interior door panel.

Jul 06, 2009 | 1997 Buick Park Avenue

1 Answer

How to replace the fuel injectors on a 2002 Tahoe?


To Install:
  1. Lubricate the NEW fuel injector O-rings with clean engine oil.
  2. Install the O-rings on the fuel injector.
  3. Install a NEW retainer clip on the fuel injector.
  4. Install the fuel injector in the injector socket with the electrical connector facing outward. The retainer clip locks onto a flange at the fuel rail injector socket.
  5. Install the fuel rail.
NOTE: Use care in removing the fuel injectors in order to prevent damage to the electrical connector pins on the injector and to prevent damage to the nozzle. Service the fuel injector as a complete assembly only. The fuel injector is an electrical component. DO NOT immerse the fuel injector in any type of cleaner.

Mar 29, 2009 | 2002 Chevrolet Tahoe

2 Answers

When i flip the little gastank door lever on my camry it won't open the door


New or Old!?
The cable is probably just broken/jumped off, lift up the carpet and you should be able to open it, by pulling at the end! NOT THE CABLE ITSELF...;)

Oct 06, 2008 | 1999 Toyota Camry

Not finding what you are looking for?
2006 Mitsubishi Outlander Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...